OPA2631U - Dual 68MHz Low-Power Op Amp | Texas Instruments
MPN: OPA2631U ✓ AktifOPA2631U Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while providing high input impedance and low output impedance. The OPA2631U belongs to the operational-amplifier hierarchy within amplifier ICs and analog signal-chain devices. Its dual-circuit configuration provides two amplifiers in one package, reducing board area when a design requires two gain channels with common supply and decoupling.
The OPA2631U combines a 68 MHz gain-bandwidth characteristic with a 100 V/us slew rate and approximately 6 mV input offset voltage. These figures support operation across signal paths that require accurate amplification of moderate-bandwidth waveforms. Its low-power bias design is suitable for portable, industrial, and embedded systems where amplifier current consumption contributes to the overall power budget.
The OPA2631U uses a single-supply architecture, which simplifies power-system design when the signal source and load operate near a positive rail. The dual amplifier can be used for independent signal channels or for active-filter and feedback configurations. Designers should still account for input common-mode limits, output swing, stability, and the required bypass capacitance when defining the operating point.
Typical applications include instrumentation signal conditioning, sensor amplification, audio and communications front ends, active filters, and low-power embedded measurement systems. The 8-SOIC package is compatible with conventional surface-mount assembly and provides a practical migration path for designs that need two high-speed amplifiers in a small footprint. The manufacturer’s datasheet should be consulted for the complete electrical limits, recommended operating conditions, and pin-level details.
For low-noise PCB design, place the supply bypass capacitors close to the power pins and keep input and feedback routing short. Avoid long high-impedance traces near the amplifier inputs, because parasitic capacitance can affect bandwidth and stability. This page combines the verified OPA2631U product information with package, application, and replacement guidance for engineers evaluating the dual low-power operational amplifier.
Pilihan pengganti yang segera untuk OPA2631U — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
OPA2604AU/2K5
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA2604AU
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA2631U Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Voltage Feedback |
| Number of Circuits | 2 |
| Supply Type | Single-Supply |
| Gain Bandwidth Product | 68 MHz |
| Slew Rate | 100 V/us |
| Arus Pemberi Arus | 11 uA |
| Input Offset Voltage | 6 mV |
| Kemasan | 8-SOIC |
| Terminal Count | 8 |
| Terminal Form | Gull Wing |
| Package Code | SOP |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
Konfigurasi Pin OPA2631U
| Pin 1 | OUTA — Output of amplifier A |
| Pin 2 | INA- — Inverting input of amplifier A |
| Pin 3 | INA+ — Non-inverting input of amplifier A |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | INB+ — Non-inverting input of amplifier B |
| Pin 6 | INB- — Inverting input of amplifier B |
| Pin 7 | OUTB — Output of amplifier B |
| Pin 8 | V+ — Positive supply connection |
Aplikasi Biasa
OPA2631U patut untuk 6 aplikasis: Instrumentation Signal Conditioning, Low-Power Sensor Amplification, Communications Front End, Active Audio Filtering, Embedded Measurement Systems, Data-Acquisition Signal Paths.
Instrumentation Signal Conditioning
OPA2631U fits instrumentation signal-conditioning stages because its 68 MHz gain-bandwidth product and 100 V/us slew rate provide useful bandwidth for moderate-frequency sensor and measurement signals. The dual-circuit arrangement allows two related channels to be amplified in one 8-SOIC package, reducing board area and simplifying supply routing. Its 11 uA supply current supports power-conscious measurement equipment. Designers should choose the closed-loop gain and feedback network with stability in mind, then verify input common-mode range, output swing, and the 6 mV offset requirement against the measurement accuracy budget.
Disebarkan
Low-Power Sensor Amplification
The OPA2631U is appropriate for low-power sensor-amplifier circuits where a compact dual amplifier and 11 uA supply current help control system consumption. Its voltage-feedback architecture supports conventional inverting and non-inverting configurations, while 68 MHz bandwidth allows it to process signals well above the bandwidth of many slow sensors. In a sensor front end, preserve input-common-mode headroom and pay attention to the 6 mV input offset specification when the output range is narrow. Place the amplifier close to the sensor or connector to minimize noise pickup and parasitic feedback paths.
Disebarkan
Communications Front End
OPA2631U can be used in communications and communications-adjacent signal paths because its 68 MHz gain-bandwidth product and 100 V/us slew rate provide substantially more speed than basic low-power general-purpose amplifiers. The dual amplifier can handle an active transmit or receive channel and an associated monitor, filter, or gain block. The 11 uA supply current is useful in portable or distributed equipment, while the 8-SOIC package supports surface-mount assembly. Check the exact input range, output swing, noise, and channel-to-channel behavior against the communications signal before fixing the gain and filter components.
Disebarkan
Active Audio Filtering
OPA2631U is suitable for active audio filters and small-signal audio stages where low power, dual-channel operation, and a 100 V/us slew rate are useful. A pair of amplifiers can implement state-variable or related active-filter topologies, while the 68 MHz gain-bandwidth product provides bandwidth margin for several common audio-frequency filter sections. The single-supply architecture simplifies integration, but the signal may require biasing for an AC-coupled input. Verify the output swing and common-mode range at the intended supply voltage, and use the datasheet's stability recommendations when operating at very low closed-loop gains.
Disebarkan
Embedded Measurement Systems
OPA2631U fits embedded measurement systems that require more bandwidth than a micropower comparator while retaining a low 11 uA supply-current characteristic. The dual circuit can amplify two measurement channels or implement a gain stage plus an active filter. Its 8-SOIC package is convenient for mixed-signal boards with conventional surface-mount assembly, and the single-supply configuration can simplify system rails. For battery-powered equipment, calculate total amplifier power from the actual rail and operating state. Also verify that the 6 mV input offset and common-mode limits support the required measurement resolution and sensor output range.
Disebarkan
Data-Acquisition Signal Paths
OPA2631U can condition fast, low-amplitude signals ahead of an analog-to-digital converter when its 68 MHz bandwidth and 100 V/us slew rate meet the acquisition bandwidth. The dual amplifier allows a differential signal to be amplified and filtered, or allows two channels to share similar conditioning. Input offset, common-mode range, and output swing are especially important because they limit usable resolution and converter range. Confirm the ADC's input range and settling requirements, then select resistor and capacitor values that preserve amplifier stability. Keep sensitive input traces short and provide local supply bypassing for repeatable acquisition performance.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk OPA2631U — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | OPA2604AU/2K5 | OPA2604AU |
|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
Penyeberangsung Jelas
- Dual low-power single-supply architecture (vsOPA2604AU)
- High bandwidth for a low-power dual amplifier (vsOPA2604AU/2K5)
- Compact integration for dual-channel designs (vsOPA2604AU)
Catatan Desain
Place the OPA2631U input and feedback components close to the relevant SOIC pins and keep high-impedance input traces short. The dual amplifier uses pins 2 and 3 for channel A inputs and pins 5 and 6 for channel B inputs. Route these nets away from switching nodes and high-current supply paths to reduce parasitic pickup and unintended feedback.
Connect the positive supply to pin 8 and the negative supply or ground reference to pin 4, with local bypass capacitance placed close to the device. Because the OPA2631U is identified as a single-supply amplifier, verify the allowable supply range and input common-mode range in the manufacturer datasheet before selecting the system rail. Avoid placing the amplifier at an electrical limit merely to reduce the number of external components.
The stated 68 MHz gain-bandwidth product and 100 V/us slew rate make trace and feedback-path discipline important. Keep feedback loops compact, terminate unused inputs according to the datasheet, and check stability at the lowest intended closed-loop gain. For sensor or communications inputs, use a ground-plane arrangement that minimizes loop area and avoids running sensitive traces beneath digital or switching-power sections.
Maklumat Kesediaan
The accessible product excerpts do not state the compliance results. The OPA2631U is an industrial-grade analog IC; confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations on the current Texas Instruments product page or manufacturer documentation.