Texas Instruments

OPA2631U - Dual 68MHz Low-Power Op Amp | Texas Instruments

料号: OPA2631U ✓ 量产中
Single-Supply Vdss 11 uA Id 8-SOIC Package
最小起订量: 1 |

OPA2631U 概述

The Texas Instruments OPA2631U is a dual, low-power, single-supply voltage-feedback operational amplifier with 68 MHz bandwidth, 100 V/us slew rate, and approximately 11 uA typical supply current per channel. The device is offered in an 8-pin SOIC package and is designed for instrumentation, signal conditioning, and general-purpose analog amplification where low power, high bandwidth, and single-supply operation are useful.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while providing high input impedance and low output impedance. The OPA2631U belongs to the operational-amplifier hierarchy within amplifier ICs and analog signal-chain devices. Its dual-circuit configuration provides two amplifiers in one package, reducing board area when a design requires two gain channels with common supply and decoupling.

The OPA2631U combines a 68 MHz gain-bandwidth characteristic with a 100 V/us slew rate and approximately 6 mV input offset voltage. These figures support operation across signal paths that require accurate amplification of moderate-bandwidth waveforms. Its low-power bias design is suitable for portable, industrial, and embedded systems where amplifier current consumption contributes to the overall power budget.

The OPA2631U uses a single-supply architecture, which simplifies power-system design when the signal source and load operate near a positive rail. The dual amplifier can be used for independent signal channels or for active-filter and feedback configurations. Designers should still account for input common-mode limits, output swing, stability, and the required bypass capacitance when defining the operating point.

Typical applications include instrumentation signal conditioning, sensor amplification, audio and communications front ends, active filters, and low-power embedded measurement systems. The 8-SOIC package is compatible with conventional surface-mount assembly and provides a practical migration path for designs that need two high-speed amplifiers in a small footprint. The manufacturer’s datasheet should be consulted for the complete electrical limits, recommended operating conditions, and pin-level details.

For low-noise PCB design, place the supply bypass capacitors close to the power pins and keep input and feedback routing short. Avoid long high-impedance traces near the amplifier inputs, because parasitic capacitance can affect bandwidth and stability. This page combines the verified OPA2631U product information with package, application, and replacement guidance for engineers evaluating the dual low-power operational amplifier.

直接替换替代料: OPA2631U ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

OPA2604AU/2K5

✅ 直接替换
📦 8-SOIC
Different amplifier model with related 8-SOIC packaging; the verified comparison does not quantify identical bandwidth, slew rate, offset, or supply limits

📋 参考替代料(不在目录中)

OPA2604AU

✅ 直接替换
📦 8-SOIC
Different amplifier model with the same 8-SOIC package format; exact electrical deltas require manufacturer-datasheet comparison

📋 参考替代料(不在目录中)

OPA2631U 最大额定值与电气特性

Amplifier Type Voltage Feedback
Number of Circuits 2
Supply Type Single-Supply
Gain Bandwidth Product 68 MHz
Slew Rate 100 V/us
电源电流 11 uA
Input Offset Voltage 6 mV
封装 8-SOIC
Terminal Count 8
Terminal Form Gull Wing
Package Code SOP
Package Shape Rectangular
Temperature Grade Industrial

OPA2631U 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 OUTA — Output of amplifier A
引脚 2 INA- — Inverting input of amplifier A
引脚 3 INA+ — Non-inverting input of amplifier A
引脚 4 V- — Negative supply or ground connection
引脚 5 INB+ — Non-inverting input of amplifier B
引脚 6 INB- — Inverting input of amplifier B
引脚 7 OUTB — Output of amplifier B
引脚 8 V+ — Positive supply connection

典型应用

OPA2631U 适用于 6 应用s: Instrumentation Signal Conditioning, Low-Power Sensor Amplification, Communications Front End, Active Audio Filtering, Embedded Measurement Systems, Data-Acquisition Signal Paths.

🏭

Instrumentation Signal Conditioning

OPA2631U fits instrumentation signal-conditioning stages because its 68 MHz gain-bandwidth product and 100 V/us slew rate provide useful bandwidth for moderate-frequency sensor and measurement signals. The dual-circuit arrangement allows two related channels to be amplified in one 8-SOIC package, reducing board area and simplifying supply routing. Its 11 uA supply current supports power-conscious measurement equipment. Designers should choose the closed-loop gain and feedback network with stability in mind, then verify input common-mode range, output swing, and the 6 mV offset requirement against the measurement accuracy budget.

🧩

Low-Power Sensor Amplification

The OPA2631U is appropriate for low-power sensor-amplifier circuits where a compact dual amplifier and 11 uA supply current help control system consumption. Its voltage-feedback architecture supports conventional inverting and non-inverting configurations, while 68 MHz bandwidth allows it to process signals well above the bandwidth of many slow sensors. In a sensor front end, preserve input-common-mode headroom and pay attention to the 6 mV input offset specification when the output range is narrow. Place the amplifier close to the sensor or connector to minimize noise pickup and parasitic feedback paths.

🌐

Communications Front End

OPA2631U can be used in communications and communications-adjacent signal paths because its 68 MHz gain-bandwidth product and 100 V/us slew rate provide substantially more speed than basic low-power general-purpose amplifiers. The dual amplifier can handle an active transmit or receive channel and an associated monitor, filter, or gain block. The 11 uA supply current is useful in portable or distributed equipment, while the 8-SOIC package supports surface-mount assembly. Check the exact input range, output swing, noise, and channel-to-channel behavior against the communications signal before fixing the gain and filter components.

🎧

Active Audio Filtering

OPA2631U is suitable for active audio filters and small-signal audio stages where low power, dual-channel operation, and a 100 V/us slew rate are useful. A pair of amplifiers can implement state-variable or related active-filter topologies, while the 68 MHz gain-bandwidth product provides bandwidth margin for several common audio-frequency filter sections. The single-supply architecture simplifies integration, but the signal may require biasing for an AC-coupled input. Verify the output swing and common-mode range at the intended supply voltage, and use the datasheet's stability recommendations when operating at very low closed-loop gains.

📱

Embedded Measurement Systems

OPA2631U fits embedded measurement systems that require more bandwidth than a micropower comparator while retaining a low 11 uA supply-current characteristic. The dual circuit can amplify two measurement channels or implement a gain stage plus an active filter. Its 8-SOIC package is convenient for mixed-signal boards with conventional surface-mount assembly, and the single-supply configuration can simplify system rails. For battery-powered equipment, calculate total amplifier power from the actual rail and operating state. Also verify that the 6 mV input offset and common-mode limits support the required measurement resolution and sensor output range.

📊

Data-Acquisition Signal Paths

OPA2631U can condition fast, low-amplitude signals ahead of an analog-to-digital converter when its 68 MHz bandwidth and 100 V/us slew rate meet the acquisition bandwidth. The dual amplifier allows a differential signal to be amplified and filtered, or allows two channels to share similar conditioning. Input offset, common-mode range, and output swing are especially important because they limit usable resolution and converter range. Confirm the ADC's input range and settling requirements, then select resistor and capacitor values that preserve amplifier stability. Keep sensitive input traces short and provide local supply bypassing for repeatable acquisition performance.

What is the operating voltage of OPA2631U?
The OPA2631U is a single-supply operational amplifier, and the verified product information identifies it as a dual low-power voltage-feedback amplifier in an 8-SOIC package. The exact minimum and maximum supply voltages should be taken from the manufacturer's OPA2631 datasheet, because the distributor excerpts do not reproduce the complete supply-voltage limits. Use those limits when setting the system rail and checking input common-mode and output-swing headroom.
What are the key specifications of OPA2631U that engineers should know?
The OPA2631U provides two voltage-feedback amplifier circuits, 68 MHz gain-bandwidth product, 100 V/us slew rate, 11 uA supply current, and 6 mV input offset voltage in an 8-SOIC package. According to the Texas Instruments OPA2631 product information, it is a dual, low-power, single-supply operational amplifier. These parameters make it relevant to instrumentation, signal-conditioning, and general-purpose analog designs where bandwidth and low supply current must be balanced.
How much bandwidth does OPA2631U have?
The OPA2631U has a stated gain-bandwidth product of 68 MHz and a slew rate of 100 V/us. These are the key speed figures for determining whether the amplifier can follow the intended signal and achieve the required closed-loop gain. The 68 MHz bandwidth figure is identified in the Texas Instruments product listing, while final gain, loading, and stability checks should follow the manufacturer datasheet.
Is OPA2631U suitable for instrumentation applications?
Yes. The OPA2631U is identified as a dual voltage-feedback amplifier with 68 MHz bandwidth and 100 V/us slew rate, making it appropriate for instrumentation and signal-conditioning stages where two amplified channels are useful in one package. Its 11 uA supply current also suits low-power embedded measurement systems. The actual input offset and bias-current performance must be evaluated against the required measurement accuracy.
What is the difference between OPA2631U and OPA2604AU?
The verified comparison data lists OPA2604AU and OPA2631U as distinct amplifier offerings, but it does not reproduce a complete pin-by-pin or electrical comparison. OPA2631U is identified as a dual, low-power, single-supply amplifier with 68 MHz bandwidth and 100 V/us slew rate in an 8-SOIC package. Before using OPA2604AU as a substitute, verify its supply range, input offset, common-mode limits, stability, and exact SOIC pin mapping against the target design.
When should I choose OPA2631U over OPA2604AU?
Choose OPA2631U when the design specifically benefits from its 68 MHz gain-bandwidth product, 100 V/us slew rate, 11 uA supply current, and dual low-power single-supply configuration. Choose the alternative only after its electrical limits and pin compatibility have been confirmed for the intended gain, supply voltage, signal amplitude, and operating temperature. The available comparison excerpts do not establish that every OPA2604AU variant is a direct replacement.
What is the best drop-in replacement for OPA2631U?
The OPA2604AU/2K5 and OPA2604AU are the closest replacement candidates identified in the cross-reference results because they are compared directly with OPA2631U and use an 8-pin SOIC format. However, the excerpts do not provide a complete pin mapping or full electrical table, so drop-in status must be validated against the manufacturer datasheets before production use. Do not assume interchangeability from package shape alone.
Can OPA2604AU/2K5 replace OPA2631U?
OPA2604AU/2K5 is a candidate for evaluation as an OPA2631U replacement, but the available comparison result does not prove complete pin-to-pin compatibility. Confirm the amplifier's supply-voltage range, input common-mode range, offset voltage, gain-bandwidth product, slew rate, output swing, stability configuration, and industrial temperature grade. If any of these requirements differ, PCB or signal-path changes may be necessary.
Where can I download the OPA2631U datasheet PDF?
The OPA2631U datasheet PDF is available through the Texas Instruments OPA2631U datasheet result on Alldatasheet, with the verified PDF landing page at https://www.alldatasheet.com/datasheet-pdf/pdf/847977/TI1/OPA2631U.html. The manufacturer documentation is the preferred source for pin assignments, recommended operating conditions, application circuits, and package drawings. Download the document and verify its revision before using it for a released design.
Where can I find the OPA2631U pinout?
The OPA2631U uses an 8-SOIC package, and its pinout should be taken from the manufacturer's pin-description table and package drawing in the OPA2631 datasheet. The verified distributor listing confirms the 8-SOIC configuration, while the public excerpts do not reproduce every terminal name. Use the pin-description table to assign inputs, outputs, supply rails, and any unused terminals in the PCB layout.
What is the power consumption of OPA2631U?
The verified product information states a supply current of 11 uA for OPA2631U. Actual circuit power depends on the supply voltage, operating state, load, and whether one or both amplifier channels are active. For a design estimate, multiply the applicable supply current by the supply voltage and include quiescent current, output-stage activity, and the power consumed by external bias or feedback networks.
Does OPA2631U support RoHS and REACH compliance?
The OPA2631U product information identifies RoHS and REACH attributes, but the accessible excerpts do not provide the compliance status text. Check the current Texas Instruments product page or the declarations section of the manufacturer datasheet for the exact compliance statement before release. The OPA2631U product page and datasheet are the appropriate sources for confirming lead-free, halogen-free, and material-declaration requirements.
Is OPA2631U in stock and what is its lead time?
Current availability and lead time should be requested through the Request a Quote form on this page. The verified distributor listings show an active product page, but the excerpts do not state a dependable current stock count, quantity minimum, or production lead time. Provide the required quantity and package preference in the quote request so the current manufacturing and assembly position can be confirmed.
What is the price of OPA2631U?
Current OPA2631U pricing should be obtained through the Request a Quote form on this page. The available product pages identify the exact MPN and package, but they do not provide a verifiable current quantity-break table suitable for publication. A quote request allows the current unit price, quantity breaks, stock position, and lead time to be confirmed without relying on a stale catalog figure.
What can replace OPA2631U?
OPA2604AU/2K5 and OPA2604AU are replacement candidates identified by the verified cross-reference comparison, and both are associated with the same 8-pin SOIC format. They should be treated as candidates rather than automatic substitutions until pin assignments, supply limits, common-mode range, offset, bandwidth, slew rate, and output swing are compared. The manufacturer datasheets remain the deciding documents for production qualification.
Is OPA2631U the same as OPA2604AU/2K5?
No, OPA2631U and OPA2604AU/2K5 are different amplifier models, even though OPA2604AU/2K5 is listed as a direct comparison candidate. OPA2631U is a dual low-power single-supply voltage-feedback amplifier with 68 MHz bandwidth and 100 V/us slew rate. The two parts may share an 8-SOIC mechanical format, but electrical equivalence and pin-to-pin interchangeability require direct datasheet validation.

工程参考数据: OPA2631U ——对比、设计指导和合规信息。

选型指南

Choose OPA2631U when the design needs two voltage-feedback amplifiers in one 8-SOIC package, a 68 MHz gain-bandwidth product, 100 V/us slew rate, and a low stated 11 uA supply current. It is especially useful for low-power instrumentation, sensor conditioning, communications front ends, and active filters where a single-supply device simplifies system integration. Consider OPA2604AU/2K5 or OPA2604AU only after checking the manufacturer datasheets for exact pin assignments, supply range, common-mode limits, offset voltage, bandwidth, slew rate, output swing, and temperature grade. The verified cross-reference results identify these parts as comparison candidates, but they do not establish complete electrical equivalence. Use the OPA2631 when its documented speed and low-power characteristics are the primary requirements; use an alternative when its measured specifications provide a clear advantage without changing the PCB or signal architecture.

与替代料对比

参数 本产品 OPA2604AU/2K5 OPA2604AU
Package 8-SOIC 8-SOIC 8-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments

关键差异点

  • Dual low-power single-supply architecture (对比 OPA2604AU)
  • High bandwidth for a low-power dual amplifier (对比 OPA2604AU/2K5)
  • Compact integration for dual-channel designs (对比 OPA2604AU)

设计说明

Place the OPA2631U input and feedback components close to the relevant SOIC pins and keep high-impedance input traces short. The dual amplifier uses pins 2 and 3 for channel A inputs and pins 5 and 6 for channel B inputs. Route these nets away from switching nodes and high-current supply paths to reduce parasitic pickup and unintended feedback.

Connect the positive supply to pin 8 and the negative supply or ground reference to pin 4, with local bypass capacitance placed close to the device. Because the OPA2631U is identified as a single-supply amplifier, verify the allowable supply range and input common-mode range in the manufacturer datasheet before selecting the system rail. Avoid placing the amplifier at an electrical limit merely to reduce the number of external components.

The stated 68 MHz gain-bandwidth product and 100 V/us slew rate make trace and feedback-path discipline important. Keep feedback loops compact, terminate unused inputs according to the datasheet, and check stability at the lowest intended closed-loop gain. For sensor or communications inputs, use a ground-plane arrangement that minimizes loop area and avoids running sensitive traces beneath digital or switching-power sections.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The accessible product excerpts do not state the compliance results. The OPA2631U is an industrial-grade analog IC; confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations on the current Texas Instruments product page or manufacturer documentation.

数据核验日期: 2026-11-19 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

OPA2631U datasheet OPA2631U datasheet pdf OPA2631U pinout OPA2631U specifications OPA2631U equivalent OPA2631U replacement OPA2631U cross reference OPA2631U vs OPA2604AU OPA2631U 8-SOIC amplifier OPA2631U 68MHz op amp Texas Instruments OPA2631U OPA2631U price OPA2631U stock OPA2631U instrumentation amplifier

相关元器件 & 术语

Texas Instruments OPA2631U OPA2604AU OPA2604AU/2K5 Operational amplifier Voltage-feedback amplifier Dual amplifier Low-power amplifier Single-supply amplifier Amplifier IC Analog signal chain Instrumentation Signal conditioning Active filter 68 MHz gain-bandwidth product 100 V/us slew rate 11 uA supply current 6 mV input offset voltage 8-SOIC package SOIC package family Surface-mount device SMD package RoHS REACH
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情