OPA317ID - Low-Offset Precision Op Amp | Texas Instruments
MPN: OPA317ID ✓ AktifOPA317ID Ringkasan
A precision operational amplifier is a voltage-feedback amplifier designed to amplify the difference between two input voltages while minimizing offset, bias-current, and temperature-related errors. The OPA317 belongs to the Zerø-Drift amplifier family and uses proprietary autocalibration technology to maintain low offset over time and temperature. In the system hierarchy, it is a CMOS operational amplifier within the broader category of analog amplifiers and signal-chain ICs.
The primary feature of the OPA317ID is its low input offset voltage, specified at no more than 90 µV. This limits the output error generated when the two amplifier inputs are at nearly equal voltages. Its maximum quiescent current of 35 µA also reduces the supply current consumed by the amplifier itself, making the device relevant to battery-powered instruments, portable sensors, and precision acquisition systems where amplifier power can materially affect system energy use.
Rail-to-rail input and output operation allows the amplifier to process signals close to the supply rails and provides greater usable input and output range than a conventional amplifier with restricted common-mode or output swing. The CMOS implementation supports low quiescent current, while the Zerø-Drift architecture targets stable precision performance across changing temperature and time. Engineers should still verify the exact supply, common-mode, output-swing, noise, bandwidth, and current limits against the manufacturer datasheet for the operating conditions of the finished circuit.
Typical uses include bridge-amplifier inputs, strain-gauge and pressure-sensor signal paths, low-current sensor interfaces, precision current measurement, battery-powered instrumentation, and low-level analog signal conditioning. In these applications, the 90 µV maximum offset specification helps constrain systematic error, while the 35 µA maximum quiescent current limits amplifier overhead. The SOIC-8 package supports conventional surface-mount assembly and is appropriate for designs that require a single amplifier with rail-to-rail signal range.
Layout should keep input traces short, place the input-bias or feedback network close to the amplifier, and route sensitive input signals away from switching nodes and high-current return paths. Bypass each supply pin as indicated by the manufacturer layout guidance, and use grounded guarding around precision inputs when leakage from PCB contamination or flux residue could otherwise influence bias current. Confirm the chosen SOIC-8 land pattern and assembly requirements before releasing the PCB footprint.
This product record combines the manufacturer description, ordering information, package details, operating-temperature information, and cross-reference resources into an engineering-focused selection guide. It also distinguishes a true same-package family alternative from the many amplifier options that are only functionally similar and therefore may require different biasing, compensation, decoupling, or verification.
Pilihan pengganti yang segera untuk OPA317ID — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
OPA317IDR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA317ID Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Low-offset, rail-to-rail input/output CMOS operational amplifier |
| Amplifier Type | Single-channel voltage-feedback operational amplifier |
| Architecture | Proprietary autocalibration Zerø-Drift |
| Maximum Input Offset Voltage | 90 µV |
| Maximum Quiescent Current | 35 µA |
| Gambaran Suhu Operasi | 40°C to 125°C |
| Kemasan | 8-pin SOIC |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin OPA317ID 8-pin soic
Konfigurasi pin untuk OPA317ID (8-pin soic pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk OPA317ID.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
OPA317ID patut untuk 6 aplikasis: Low-Power Bridge Amplifier, Battery-Powered Sensor Interface, Precision Current Measurement, Low-Level Signal Conditioning, Precision Data Acquisition Front End, Environmental and Process Monitoring.
Low-Power Bridge Amplifier
The OPA317ID is suitable for conditioning differential outputs from resistive bridge sensors such as pressure, force, and strain gauges. Its maximum input offset voltage of 90 µV limits the systematic input-referred error that can become significant when the bridge excitation and full-scale sensor output are small. The low maximum quiescent current of 35 µA also helps preserve battery life in portable test equipment. Place the amplifier close to the bridge and use short, guarded input traces to minimize leakage and thermal gradients. Feedback and gain-setting resistors should be positioned to maintain low parasitic capacitance. Confirm the exact input common-mode range, output swing, and gain-bandwidth limits against the manufacturer datasheet for the selected bridge excitation and gain.
Battery-Powered Sensor Interface
OPA317ID can serve as the precision gain stage in a battery-powered sensor interface because it combines rail-to-rail input and output operation with a maximum quiescent current of 35 µA. These characteristics are useful when a sensor produces a signal near one of the supply rails and when every microampere affects operating time. The amplifier's maximum 90 µV offset can be important for slow, low-level measurements where input-referred error changes the interpreted sensor value. Use a low-leakage PCB surface and clean assembly practices around high-impedance inputs. The complete current budget should include sensor excitation, reference circuitry, and any pull-up or pull-down networks rather than considering only the OPA317ID quiescent current.
Precision Current Measurement
The OPA317ID fits a precision current-measurement amplifier when the shunt voltage is small and measurement accuracy depends on low offset. Its 90 µV maximum input offset specification helps limit the voltage error introduced at the amplifier input before gain and analog-to-digital conversion. The 35 µA maximum quiescent current is beneficial in portable multimeters, laboratory instruments, and energy-monitoring equipment. Place the amplifier adjacent to the shunt or current-sense node so the sensitive input does not pick up board-level noise. Verify common-mode limits when the shunt is placed on a high-side supply rail, and check output-swing requirements for the chosen shunt current and reference voltage.
Low-Level Signal Conditioning
OPA317ID is appropriate for low-level analog signal conditioning when the desired result depends on accurate difference amplification rather than maximum bandwidth. The Texas Instruments OPA317 family uses proprietary autocalibration to achieve low offset over time and temperature, with the OPA317ID specified at no more than 90 µV. This can improve repeatability in instrumentation, biomedical-adjacent measurement, and laboratory sensor interfaces. Configure the feedback network according to the required closed-loop gain and verify stability with the manufacturer application guidance. Keep input and feedback nodes compact and avoid routing them beneath digital clocks, display drivers, or switching-regulator components that could inject correlated disturbance.
Precision Data Acquisition Front End
OPA317ID can amplify a sensor output before an ADC in a precision data-acquisition system. The single-channel amplifier provides rail-to-rail input and output behavior, a maximum offset voltage of 90 µV, and a maximum quiescent current of 35 µA, allowing an engineer to balance input-referred accuracy against power consumption. This balance is useful in compact measurement instruments where the analog front end must operate near the converter's input range. The analog and digital grounds should meet at a controlled location, while the amplifier input should be driven from a low-impedance source. Before implementation, confirm gain-bandwidth, slew rate, output swing, and settling behavior against the ADC sampling requirements.
Environmental and Process Monitoring
OPA317ID is suitable for slow industrial or environmental monitoring loops that measure temperature, humidity, gas, or liquid level through resistive or bridge sensors. Its low offset can reduce fixed measurement error, and the 35 µA maximum quiescent current supports long-duration, battery-assisted field monitoring. The 8-pin SOIC package is straightforward to assemble in conventional surface-mount hardware and remains usable across the manufacturer's stated 40°C to 125°C operating range. Use the device close to the sensing element where cable pickup could otherwise dominate the error. Apply protection networks for exposed sensor lines, and ensure that leakage through protection components does not compromise input bias current or signal accuracy.
Data referensi kejuruteraan untuk OPA317ID — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | OPA317IDR |
|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | Single-channel low-offset rail-to-rail I/O operational amplifier | Single-channel low-offset rail-to-rail I/O operational amplifier |
| Maximum Input Offset Voltage | 90 µV | 90 µV |
| Maximum Quiescent Current | 35 µA | 35 µA |
| Operating Temperature Range | 40°C to 125°C | 40°C to 125°C |
| Amplifier Architecture | Proprietary autocalibration Zerø-Drift | Proprietary autocalibration Zerø-Drift |
| Channel Count | 1 channel | 1 channel |
Penyeberangsung Jelas
- Very low quiescent current for a precision amplifier (vsOPA317IDR)
- Maximum offset limited to 90 µV (vsOPA317IDR)
- Rail-to-rail input and output operation (vsOPA317IDR)
Catatan Desain
Place the OPA317ID close to the source of the precision signal and route inputs as short traces with a continuous ground reference. Keep the feedback network close to the amplifier so parasitic resistance and capacitance do not alter the intended gain or stability. Sensitive input traces should avoid switching nodes, inductors, and the return path of high-current loads.
Apply grounded guarding when driving a high-impedance source because PCB contamination, flux residue, and moisture can create leakage paths comparable to the amplifier's bias current. Keep the area around the input pins clean and avoid long exposed copper where condensation or contamination could affect accuracy. The 35 µA maximum quiescent current makes the amplifier efficient, but it does not eliminate input-leakage concerns.
Estimated: the amplifier's supply dissipation is approximately P = VIN × IQ. Using the maximum quiescent current of 35 µA and a 5 V supply gives about 175 µW, before output current, feedback-network current, and external-circuit consumption are included. Calculate the complete rail budget separately because the amplifier may not be the dominant load in a precision measurement system.
Do not assume that low offset alone guarantees usable precision performance. Check input common-mode range, output swing, gain-bandwidth product, slew rate, noise, and stability for the selected operating point. The rail-to-rail designation does not eliminate all headroom requirements, and the 90 µV offset is a maximum limit rather than a guaranteed value for every unit.
Maklumat Kesediaan
Compliance attributes were not stated in the referenced product information. Confirm current environmental declarations and qualification status with Texas Instruments before production release.