OPA842ID - 400 MHz Low-Distortion Op Amp | Texas Instruments
MPN: OPA842ID ✓ AktifOPA842ID Ringkasan
An operational amplifier is a high-gain differential amplifier used to amplify small input signals while imposing minimal distortion or unwanted noise. The OPA842 belongs to the voltage-feedback amplifier family within the broader operational-amplifier and signal-conditioning semiconductor hierarchy. Its unity-gain stability permits operation as a low-noise gain stage without requiring external compensation for a unity-gain configuration.
The device uses a voltage-feedback architecture with two internal gain stages. According to the Texas Instruments OPA842 product information, this design provides a combination of high speed and dynamic range while maintaining low harmonic distortion across a wide frequency range. The 400 MHz gain-bandwidth product supports high-bandwidth signal processing, while the 400 V/us slew rate allows the amplifier to reproduce large-amplitude, rapidly changing signals with limited slew distortion.
OPA842ID is suitable for test and measurement, communications, video, imaging, and general-purpose analog signal-chain applications. It can serve as a low-gain buffer, a wideband voltage amplifier, a driver for downstream circuitry, or an active element in analog filtering and feedback networks. Unity-gain stability is especially useful when the required closed-loop gain is close to 1.
The principal design tradeoff is operating speed versus power dissipation and system noise. High-speed feedback loops require short, well-controlled PCB traces, stable power-supply bypassing, and careful termination of unused inputs. Follow the pin-description and typical-application tables in the manufacturer datasheet when assigning input bias, supply connections, output loads, and compensation values.
This product page consolidates the verified device identity, package and operating details, application guidance, comparison parameters, and design considerations needed to evaluate OPA842ID before schematic capture or prototype assembly.
Pilihan pengganti yang segera untuk OPA842ID — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
OPA842IDG4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA842IDR
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA842IDRG4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
OPA842ID Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 400 MHz |
| Slew Rate | 400 V/us |
| Unity-Gain Stable | Yes |
| Architecture | Two internal gain stages |
| Supply Voltage Range | ±5 V to ±6 V |
| Gambaran Suhu Operasi | -40 °C to +85 °C |
| Kemasan | 8-pin SOIC (D) |
| Bilangan Pin | 8 pins |
| Jenis Pemasangan | Surface mount |
| Minimum Gain | 1 V/V |
Panduan Konfigurasi Pin OPA842ID 8-pin soic (d)
Konfigurasi pin untuk OPA842ID (8-pin soic (d) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk OPA842ID.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
OPA842ID patut untuk 6 aplikasis: Wideband Instrumentation Signal Conditioning, Communications Receiver Front End, Video Signal Amplification, High-Speed Active Filtering, Precision Feedback Control, Buffering and Driver Stages.
Wideband Instrumentation Signal Conditioning
OPA842ID fits wideband instrumentation because its 400 MHz gain-bandwidth product and 400 V/us slew rate preserve the amplitude and phase relationship of rapidly changing sensor signals. The unity-gain-stable voltage-feedback architecture allows the amplifier to serve directly as a buffer or as a low-noise gain stage when higher closed-loop gains are required. Placing the device close to the sensor and its analog-to-digital converter can reduce parasitic loading and improve signal integrity. Designers should still evaluate input noise, offset, common-mode range, and output-swing limits against the precision requirements of the measurement chain.
Communications Receiver Front End
OPA842ID is suitable for intermediate-frequency and wideband receiver signal conditioning where fast settling and low distortion are important. Its 400 MHz gain-bandwidth product provides bandwidth for amplitude- and phase-corrected gain stages, while the 400 V/us slew rate reduces distortion on high-amplitude bursts. Unity-gain stability supports use as a buffer between RF-demodulated stages and downstream converters. The implementation should include controlled impedance routing, short feedback paths, and local supply bypassing so that high-speed behavior is not limited by board parasitics.
Video Signal Amplification
OPA842ID can amplify video signals in monitoring, imaging, and broadcast equipment when its speed is sufficient for the target bandwidth. The 400 MHz gain-bandwidth product offers ample closed-loop bandwidth for many video paths, and the 400 V/us slew rate helps maintain waveform shape during transitions. Because the amplifier is unity-gain stable, it can support both unity-gain buffering and moderate gain configurations. Confirm output swing, load capability, gain flatness, and distortion for the specific video format before fixing the circuit.
High-Speed Active Filtering
OPA842ID is useful in active analog filters that need high bandwidth and low distortion. Its unity-gain-stable voltage-feedback topology can be configured in conventional inverting and non-inverting filter networks, while the two-stage internal architecture is intended to provide strong speed and dynamic-range performance. Component values should account for the amplifier’s gain-bandwidth behavior, output loading, and feedback-noise contributions. Place filter resistors and capacitors close to the relevant pins and validate stability and response across the intended frequency range with the manufacturer’s application information.
Precision Feedback Control
OPA842ID can serve in high-bandwidth feedback-control loops where rapid correction and low harmonic distortion are valuable. The 400 V/us slew rate allows the amplifier to respond quickly to error signals, and unity-gain stability simplifies direct unity-follower implementations. Care is required because high-speed feedback systems can amplify delay, board capacitance, and compensation-network tolerances. The loop should be evaluated for stability, noise, output-current demand, and supply rejection, with component placement following the manufacturer’s high-speed layout guidance.
Buffering and Driver Stages
OPA842ID works as a high-speed buffer or output driver when a source cannot directly drive the intended load. Unity-gain stability avoids the need for external compensation in a follower configuration, and the 400 MHz gain-bandwidth product provides substantial open-loop bandwidth for closed-loop signal processing. The 400 V/us slew rate improves edge fidelity on fast transients. Engineers should verify output-current capability, output-voltage swing, capacitive-load stability, and power dissipation using the manufacturer electrical characteristics before assigning the final load.
Data referensi kejuruteraan untuk OPA842ID — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Catatan Desain
Place the OPA842ID close to its feedback network and the signal it drives. Keep input and feedback traces short, use a continuous ground reference, and avoid routing sensitive nodes beneath or alongside high-speed output and supply paths. The 400 V/us slew rate can couple through supply and ground impedance, so component placement and return paths are as important as nominal trace length.
Use the shortest practical connection from each supply pin to local decoupling. Confirm that the dual-rail source can support the amplifier’s operating current and transient demand within the ±5 V to ±6 V supply range. Do not substitute a lower-voltage rail arrangement without checking the absolute maximum and recommended operating conditions in the manufacturer datasheet.
Avoid assuming that unity-gain stability guarantees stable operation with every capacitive or inductive load. Check the recommended output-load conditions, use a suitable isolation resistor if required, and validate the final network at the intended frequency and output amplitude. Also follow the datasheet’s guidance for any no-connect input pin rather than leaving an input floating.
Maklumat Kesediaan
The verified product results do not state a specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status for OPA842ID. The operating-temperature range of -40 °C to +85 °C does not itself establish AEC-Q100 qualification.