NXP Semiconductors

PCF8584P - 90 kHz Multi-Master I2C Controller | NXP

MPN: PCF8584P ✓ Aktif
4.5 V to 5.5 V Vdss 20-pin PDIP Package
MOQ: 1 |

PCF8584P Ringkasan

NXP Semiconductors PCF8584P is a multi-master I2C bus controller designed to transfer data at up to 90 kHz while supporting dual addressing modes and full arbitration. The device is packaged in a 20-pin PDIP and operates from a 4.5 V to 5.5 V supply, making it suitable for legacy parallel-interface industrial equipment that must connect to an I2C bus.

An I2C bus controller is an interface IC that mediates communication between a host using a parallel or general-purpose processor interface and devices connected to the two-wire I2C bus. It sits within the broader interface-controller hierarchy: I2C controller, bus interface IC, interface bridge, and semiconductor. This positioning allows older parallel systems to exchange commands and data with sensors, memory devices, converters, and other I2C peripherals without redesigning the host bus architecture.

The PCF8584P provides multi-master operation, dual addressing modes, and full arbitration. These features support shared-bus designs in which more than one potential controller may initiate communication. The 90 kHz maximum transfer rate is appropriate for moderate-speed control and data-exchange functions rather than high-bandwidth storage or display workloads. Its 4.5 V to 5.5 V operating range supports conventional 5 V industrial logic systems.

The 20-pin PDIP package provides through-hole mounting, making PCF8584P well suited to legacy controller boards, industrial control equipment, test systems, and products where field replacement or retrofit is important. A parallel-to-I2C controller role allows the host processor to communicate through a parallel interface while the PCF8584P manages serial bus transactions. Dual addressing modes provide flexibility when integrating peripherals that use different address conventions or command structures.

Typical applications include industrial instrumentation, programmable logic controllers, legacy data-acquisition equipment, embedded control modules, and factory automation systems. The device can also bridge a parallel host processor to sensors, EEPROMs, ADC or DAC devices, and other I2C components. System designers should account for the 90 kHz bus limit and use appropriate pull-up resistors and bus capacitance when laying out the I2C network.

The principal design consideration is compatibility with the existing host interface and 20-pin through-hole footprint. Confirm signal levels, addressing, arbitration behavior, and timing against the manufacturer datasheet before replacing an existing component. Because this is a mature parallel-to-I2C architecture, it is most valuable when maintaining legacy equipment rather than implementing a new compact embedded bus interface.

This page combines the manufacturer specification, package information, interface characteristics, sourcing guidance, and engineering-oriented application analysis to help designers evaluate the PCF8584P for legacy I2C expansion and industrial retrofit work.

Pilihan pengganti yang segera untuk PCF8584P — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

PCF8584PN

✅ Masuk Drop-In
📦 20-pin PDIP
Same NXP controller family and DIP-20 footprint; ordering suffix differs by 0%, with no verified performance difference

📋 Alternatif rujukan (tidak dalam katalog)

PCF8584P Spesifikasi

Device Type Multi-master I2C bus controller
Bus Interface I2C
Host Interface Parallel
Maximum I2C Data Transfer Rate 90 kHz
Addressing Modes 2 modes
Arbitration Full arbitration
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5.00 V
Gambaran Suhu Operasi -40 °C to +85 °C
Kemasan 20-pin PDIP
Bilangan Pin 20 pins
Gaya Pemasangan Through-hole
Master Capability Multi-master

Panduan Konfigurasi Pin PCF8584P 20-pin pdip

Konfigurasi pin untuk PCF8584P (20-pin pdip pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 20-pin pdip untuk PCF8584P

Tiada data garisan pin yang diperoleh untuk PCF8584P.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

PCF8584P patut untuk 6 aplikasis: Legacy PLC I2C Expansion, Industrial Sensor Interface, Data Acquisition Retrofit, Programmable Test Equipment, Factory Automation Controller, Embedded Service Module.

🏭

Legacy PLC I2C Expansion

The PCF8584P fits legacy programmable logic controllers that retain a parallel processor interface but need to communicate with modern I2C peripherals. Its multi-master capability and full arbitration allow the controller to participate reliably in shared-bus industrial systems, while the 90 kHz maximum transfer rate is suitable for configuration, sensor, and status traffic. The 4.5 V to 5.5 V operating range aligns with conventional 5 V control electronics, and the 20-pin PDIP package simplifies installation on existing through-hole control boards.

🧩

Industrial Sensor Interface

PCF8584P can bridge a parallel host processor to I2C-based industrial sensors, allowing existing equipment to retain its processor architecture while adding digital sensing channels. The controller's dual addressing modes support different peripheral address structures, and full arbitration helps coordinate access on a shared bus. Its 90 kHz transfer ceiling accommodates typical environmental, pressure, position, and process measurements while leaving ample time for host-side processing and diagnostics.

📺

Data Acquisition Retrofit

The PCF8584P is useful in data-acquisition equipment that must add I2C converters, EEPROMs, or digital sensors without replacing a working parallel-host processor. A 90 kHz bus rate is appropriate for moderate measurement data and configuration traffic, while multi-master operation permits orderly coordination with another bus controller. The through-hole PDIP format supports repair and retrofit of older laboratory or industrial platforms, provided the host timing and software model match the device architecture.

🔧

Programmable Test Equipment

PCF8584P can serve as an interface controller in programmable test and measurement equipment where a legacy parallel system must reach I2C instruments or peripheral modules. The dual addressing modes provide flexibility in organizing instrument and accessory addresses, and full arbitration supports bus sharing in coordinated test sequences. Its -40 °C to +85 °C range is suitable for many industrial environments, although system-level thermal and EMC requirements must still be evaluated separately.

🏭

Factory Automation Controller

The PCF8584P fits factory automation modules that retain a parallel logic section but need standardized I2C connectivity to sensors, memory, and actuator interfaces. Multi-master operation and full arbitration make it suitable for coordinated access among multiple functional blocks, while 90 kHz provides sufficient throughput for control and supervisory data. Its 5 V supply range and 20-pin through-hole package are compatible with long-life industrial boards designed around pluggable controller logic.

🔧

Embedded Service Module

PCF8584P can add I2C peripheral access to embedded service modules based on older parallel processors. This approach is particularly useful when maintaining field-installed equipment because the host firmware and processor can remain intact while the controller handles protocol translation and bus arbitration. Two addressing modes assist with mixed peripheral populations, although the 90 kHz rate should be checked against logging, update, and real-time data requirements before deployment.

Ringkasan Produk Disebarkan

PCF8584PN Same-family 20-pin PDIP controller option Dipergunakan di: Legacy PLC I2C Expansion, Industrial Sensor Interface, Data Acquisition Retrofit, Programmable Test Equipment, Factory Automation Controller, Embedded Service Module
What is the PCF8584P used for?
The PCF8584P is a multi-master I2C bus controller used to connect a parallel-interface host processor to devices on a two-wire I2C bus. NXP describes support for data transfer at up to 90 kHz, two addressing modes, and full arbitration. It is particularly useful when an existing industrial controller uses a parallel interface but must communicate with I2C sensors, memory, converters, or other peripherals.
What is the maximum I2C transfer rate of the PCF8584P?
The PCF8584P supports I2C data transfer at up to 90 kHz. This rate is appropriate for control, configuration, and moderate-volume sensor traffic rather than high-speed graphics, video, or mass-storage transfers. The limit must be considered together with bus capacitance, pull-up resistance, clock stretching behavior, and the timing requirements of each connected peripheral.
What is the operating voltage of the PCF8584P?
The PCF8584P operates from 4.5 V to 5.5 V and is intended for 5 V systems. Its 20-pin PDIP package and 5 V supply range fit conventional industrial logic designs. Confirm that the host processor, pull-up network, connected I2C devices, and any level translators all use compatible voltage levels before installation.
Where can I download the PCF8584P datasheet PDF?
The official PCF8584 datasheet is available from NXP at https://www.nxp.com/docs/en/data-sheet/PCF8584.pdf. It is the primary document for the device's electrical characteristics, operating conditions, timing, pin descriptions, and application information. Use the manufacturer's document when assigning PCB signals, selecting pull-ups, checking initialization, or validating a legacy replacement.
Where can I find the PCF8584P pinout?
The PCF8584P pinout and pin descriptions are located in the NXP manufacturer datasheet at https://www.nxp.com/docs/en/data-sheet/PCF8584.pdf. The component uses a 20-pin PDIP package. Consult the datasheet's pin-description table and package drawing before assigning signals because an incorrect host, clock, data, address, or supply connection can prevent bus operation.
Does the PCF8584P support multi-master operation?
Yes, the PCF8584P supports multi-master operation with full arbitration. According to the NXP product page, this enables multiple bus controllers to share the same I2C bus while managing simultaneous access attempts. In a practical system, only one master should actively drive the bus at a given time, and every attached device must obey compatible I2C addressing and electrical rules.
What is the difference between PCF8584P and PCF8584PN?
PCF8584P and PCF8584PN identify closely related NXP 20-pin PDIP versions, with the listed comparison describing both as through-hole DIP-20 devices operating in the same voltage class. The suffix can denote ordering or packaging information rather than a functional difference. Confirm the manufacturer ordering information and compare the specific datasheet revision before using either part in a procurement or design decision.
Is PCF8584P suitable for industrial control systems?
The PCF8584P is suitable for industrial interface work where a legacy parallel host must communicate with I2C peripherals. Its multi-master operation, full arbitration, 4.5 V to 5.5 V supply range, and -40 °C to +85 °C operating range support conventional 5 V industrial electronics. The 90 kHz bus rate and PDIP package are especially useful for retrofit and long-life equipment.
What can replace the PCF8584P?
PCF8584PN is the closest documented same-package candidate identified for the PCF8584P, retaining a 20-pin through-hole DIP configuration and the same controller-device family. No independently verified cross-brand, pin-compatible replacement was identified. Because exact host timing, initialization, addressing, and arbitration behavior matter, do not substitute a generic I2C bridge without checking the complete interface requirements.
Can a generic parallel-to-I2C bridge replace the PCF8584P?
A generic parallel-to-I2C bridge is not automatically a drop-in replacement for the PCF8584P. A valid replacement must match the 20-pin PDIP footprint, supply range, host interface timing, address handling, multi-master behavior, and arbitration sequence. PCF8584PN is the closest identified same-package option, while cross-brand equivalents require application-specific verification rather than assumption.
When should I choose the PCF8584P over a modern I2C peripheral?
Choose the PCF8584P when an existing host exposes a parallel interface and the product must add I2C connectivity without changing that host processor. Its multi-master support, full arbitration, and 90 kHz transfer capability suit controlled industrial bus traffic. For new compact systems, a microcontroller or SoC with native I2C may be simpler and may eliminate the bridge entirely.
PCF8584P vs PCF8584PN: which version should I select?
PCF8584P is the target device, while PCF8584PN is the closest documented related NXP option in a 20-pin PDIP package. Both appear in the same device family and the listed comparison reports the same through-hole mounting and 5 V operating class. Final selection should follow the manufacturer ordering table, including suffix, packing, temperature, and lifecycle requirements for the intended production configuration.
What are the key specifications of PCF8584P that engineers should know?
The PCF8584P is a parallel-to-I2C multi-master controller with a maximum I2C transfer rate of 90 kHz. It supports two addressing modes and full arbitration, operates from 4.5 V to 5.5 V, and is specified from -40 °C to +85 °C. Its 20-pin PDIP package is intended for through-hole mounting in legacy and industrial systems.
Is the PCF8584P in stock and what is the lead time?
Current stock, minimum order quantity, and production lead time should be confirmed through the Request a Quote form on this page. The manufacturer product page and distributor listings show that the PCF8584P remains documented, but they do not establish a guaranteed inventory quantity or a universal lead time. Submit the required quantity, package suffix, and target date with the quote request.
How much does the PCF8584P cost and where can I buy it?
Current pricing for the PCF8584P should be obtained through the Request a Quote form on this page because commercial terms can change with quantity, suffix, packing, and supply status. Include the exact 20-pin PDIP ordering variant, annual demand, and target shipment date. Do not treat a family-level or obsolete-suffix price as a quotation for the required PCF8584P configuration.

Data referensi kejuruteraan untuk PCF8584P — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose PCF8584P when maintaining or extending a 5 V industrial product with a parallel host processor that must access I2C peripherals. Its multi-master operation, full arbitration, two addressing modes, and 90 kHz transfer rate make it appropriate for shared industrial buses carrying control, configuration, and sensor traffic. Choose PCF8584PN when the manufacturer's ordering table confirms that suffix matches the required mechanical, temperature, packing, and procurement configuration. For a new product, evaluate a microcontroller or processor with native I2C because it may remove the bridge, reduce board area, and simplify firmware. Do not select a generic parallel-to-I2C converter without proving pin compatibility, host timing, supply compatibility, initialization, address handling, and arbitration behavior. The parallel architecture remains most valuable when the existing host platform must be preserved and only the communications subsystem is being upgraded.

Perbandingan dengan Gantian

Parametr Produk Ini PCF8584PN
Brand NXP Semiconductors NXP Semiconductors
Package 20-pin PDIP 20-pin PDIP - same package
Device Type Multi-master I2C bus controller I2C bus controller
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V
Operating Temperature Range -40 °C to +85 °C -40 °C
Mounting Style Through-hole Through-hole

Penyeberangsung Jelas

  • Multi-master operation with full arbitration (vsPCF8584PN)
  • Documented 90 kHz bus performance (vsPCF8584PN)
  • Retrofit-friendly 20-pin PDIP construction (vsPCF8584PN)

Catatan Desain

Use the manufacturer pin-description table before assigning the 20-pin PDIP footprint. In particular, verify the host interface, I2C clock and data signals, address-related connections, supply pins, and ground connections against the specific datasheet revision. Because the component is intended as a retrofit part, do not infer pin positions from another parallel-to-I2C controller.

Treat the I2C clock and data nets as a shared bus and calculate the pull-up arrangement from bus capacitance, voltage, sink current, and the 90 kHz maximum transfer rate. Keep the bus away from switching nodes and high-current edges, and follow the datasheet's input and output timing requirements. Level translation, if required, must preserve compatible rise and fall times.

Do not substitute a generic parallel-to-I2C bridge solely because the connector counts match. A functional replacement must also preserve the 20-pin PDIP footprint, 4.5 V to 5.5 V supply compatibility, addressing model, initialization sequence, clocking model, and arbitration behavior. Check the manufacturer ordering information before substituting PCF8584PN or any proposed cross-brand device.

Provide a stable 5 V rail within the 4.5 V to 5.5 V operating range and follow the datasheet's decoupling requirements. Place local supply and ground-plane connections to minimize loop area, especially when the controller communicates with long or slow I2C wiring. Assess the complete system's noise margin rather than assuming the controller's supply range alone guarantees reliable communication.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Compliance status is not stated in the manufacturer page, manufacturer datasheet excerpt, or distributor listings reviewed for PCF8584P. Verify current declarations with NXP or the authorized supply source before production release.

Data disahkan pada: 2026-11-10 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

PCF8584P datasheet PCF8584P datasheet pdf PCF8584P pinout PCF8584P schematic PCF8584P equivalent PCF8584P replacement PCF8584P cross reference PCF8584P vs PCF8584PN PCF8584P footprint PCF8584P application circuit NXP PCF8584P PCF8584P price PCF8584P stock

Komponen dan Tanda berkaitan

NXP Semiconductors PCF8584P PCF8584PN PCF8584 multi-master I2C bus controller parallel-to-I2C converter I2C bus interface controller interface bridge semiconductor full arbitration dual addressing modes 90 kHz data transfer rate 4.5 V to 5.5 V supply 20-pin PDIP DIP-20 through-hole mounting industrial control legacy controller retrofit parallel host processor programmable logic controller data acquisition factory automation RoHS
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ