PCF8584P - 90 kHz Multi-Master I2C Controller | NXP
MPN: PCF8584P ✓ فعالPCF8584P نمای کلی
An I2C bus controller is an interface IC that mediates communication between a host using a parallel or general-purpose processor interface and devices connected to the two-wire I2C bus. It sits within the broader interface-controller hierarchy: I2C controller, bus interface IC, interface bridge, and semiconductor. This positioning allows older parallel systems to exchange commands and data with sensors, memory devices, converters, and other I2C peripherals without redesigning the host bus architecture.
The PCF8584P provides multi-master operation, dual addressing modes, and full arbitration. These features support shared-bus designs in which more than one potential controller may initiate communication. The 90 kHz maximum transfer rate is appropriate for moderate-speed control and data-exchange functions rather than high-bandwidth storage or display workloads. Its 4.5 V to 5.5 V operating range supports conventional 5 V industrial logic systems.
The 20-pin PDIP package provides through-hole mounting, making PCF8584P well suited to legacy controller boards, industrial control equipment, test systems, and products where field replacement or retrofit is important. A parallel-to-I2C controller role allows the host processor to communicate through a parallel interface while the PCF8584P manages serial bus transactions. Dual addressing modes provide flexibility when integrating peripherals that use different address conventions or command structures.
Typical applications include industrial instrumentation, programmable logic controllers, legacy data-acquisition equipment, embedded control modules, and factory automation systems. The device can also bridge a parallel host processor to sensors, EEPROMs, ADC or DAC devices, and other I2C components. System designers should account for the 90 kHz bus limit and use appropriate pull-up resistors and bus capacitance when laying out the I2C network.
The principal design consideration is compatibility with the existing host interface and 20-pin through-hole footprint. Confirm signal levels, addressing, arbitration behavior, and timing against the manufacturer datasheet before replacing an existing component. Because this is a mature parallel-to-I2C architecture, it is most valuable when maintaining legacy equipment rather than implementing a new compact embedded bus interface.
This page combines the manufacturer specification, package information, interface characteristics, sourcing guidance, and engineering-oriented application analysis to help designers evaluate the PCF8584P for legacy I2C expansion and industrial retrofit work.
جایگزینهای drop-in برای PCF8584P — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
PCF8584PN
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PCF8584P مشخصات
| Device Type | Multi-master I2C bus controller |
| Bus Interface | I2C |
| Host Interface | Parallel |
| Maximum I2C Data Transfer Rate | 90 kHz |
| Addressing Modes | 2 modes |
| Arbitration | Full arbitration |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5.00 V |
| محدوده دمای کاری | -40 °C to +85 °C |
| بستهبندی | 20-pin PDIP |
| تعداد پینها | 20 pins |
| سبک نصب | Through-hole |
| Master Capability | Multi-master |
راهنمای پیکربندی پین PCF8584P 20-pin pdip
پیکربندی پین برای PCF8584P (پکیج 20-pin pdip). شمارهگذاری پایهها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعملهای لحیمکاری به آن مراجعه کنید.
داده پینآوت تفصیلی موجود نیست برای PCF8584P.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
PCF8584P مناسب است برای 6 کاربردs: Legacy PLC I2C Expansion, Industrial Sensor Interface, Data Acquisition Retrofit, Programmable Test Equipment, Factory Automation Controller, Embedded Service Module.
Legacy PLC I2C Expansion
The PCF8584P fits legacy programmable logic controllers that retain a parallel processor interface but need to communicate with modern I2C peripherals. Its multi-master capability and full arbitration allow the controller to participate reliably in shared-bus industrial systems, while the 90 kHz maximum transfer rate is suitable for configuration, sensor, and status traffic. The 4.5 V to 5.5 V operating range aligns with conventional 5 V control electronics, and the 20-pin PDIP package simplifies installation on existing through-hole control boards.
پیشنهادی
Industrial Sensor Interface
PCF8584P can bridge a parallel host processor to I2C-based industrial sensors, allowing existing equipment to retain its processor architecture while adding digital sensing channels. The controller's dual addressing modes support different peripheral address structures, and full arbitration helps coordinate access on a shared bus. Its 90 kHz transfer ceiling accommodates typical environmental, pressure, position, and process measurements while leaving ample time for host-side processing and diagnostics.
پیشنهادی
Data Acquisition Retrofit
The PCF8584P is useful in data-acquisition equipment that must add I2C converters, EEPROMs, or digital sensors without replacing a working parallel-host processor. A 90 kHz bus rate is appropriate for moderate measurement data and configuration traffic, while multi-master operation permits orderly coordination with another bus controller. The through-hole PDIP format supports repair and retrofit of older laboratory or industrial platforms, provided the host timing and software model match the device architecture.
پیشنهادی
Programmable Test Equipment
PCF8584P can serve as an interface controller in programmable test and measurement equipment where a legacy parallel system must reach I2C instruments or peripheral modules. The dual addressing modes provide flexibility in organizing instrument and accessory addresses, and full arbitration supports bus sharing in coordinated test sequences. Its -40 °C to +85 °C range is suitable for many industrial environments, although system-level thermal and EMC requirements must still be evaluated separately.
پیشنهادی
Factory Automation Controller
The PCF8584P fits factory automation modules that retain a parallel logic section but need standardized I2C connectivity to sensors, memory, and actuator interfaces. Multi-master operation and full arbitration make it suitable for coordinated access among multiple functional blocks, while 90 kHz provides sufficient throughput for control and supervisory data. Its 5 V supply range and 20-pin through-hole package are compatible with long-life industrial boards designed around pluggable controller logic.
پیشنهادی
Embedded Service Module
PCF8584P can add I2C peripheral access to embedded service modules based on older parallel processors. This approach is particularly useful when maintaining field-installed equipment because the host firmware and processor can remain intact while the controller handles protocol translation and bus arbitration. Two addressing modes assist with mixed peripheral populations, although the 90 kHz rate should be checked against logging, update, and real-time data requirements before deployment.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای PCF8584P — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | PCF8584PN |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 20-pin PDIP | 20-pin PDIP - same package |
| Device Type | Multi-master I2C bus controller | I2C bus controller |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C |
| Mounting Style | Through-hole | Through-hole |
تفاوتهای کلیدی
- Multi-master operation with full arbitration (در مقابلPCF8584PN)
- Documented 90 kHz bus performance (در مقابلPCF8584PN)
- Retrofit-friendly 20-pin PDIP construction (در مقابلPCF8584PN)
یادداشتهای طراحی
Use the manufacturer pin-description table before assigning the 20-pin PDIP footprint. In particular, verify the host interface, I2C clock and data signals, address-related connections, supply pins, and ground connections against the specific datasheet revision. Because the component is intended as a retrofit part, do not infer pin positions from another parallel-to-I2C controller.
Treat the I2C clock and data nets as a shared bus and calculate the pull-up arrangement from bus capacitance, voltage, sink current, and the 90 kHz maximum transfer rate. Keep the bus away from switching nodes and high-current edges, and follow the datasheet's input and output timing requirements. Level translation, if required, must preserve compatible rise and fall times.
Do not substitute a generic parallel-to-I2C bridge solely because the connector counts match. A functional replacement must also preserve the 20-pin PDIP footprint, 4.5 V to 5.5 V supply compatibility, addressing model, initialization sequence, clocking model, and arbitration behavior. Check the manufacturer ordering information before substituting PCF8584PN or any proposed cross-brand device.
Provide a stable 5 V rail within the 4.5 V to 5.5 V operating range and follow the datasheet's decoupling requirements. Place local supply and ground-plane connections to minimize loop area, especially when the controller communicates with long or slow I2C wiring. Assess the complete system's noise margin rather than assuming the controller's supply range alone guarantees reliable communication.
اطلاعات انطباق
Compliance status is not stated in the manufacturer page, manufacturer datasheet excerpt, or distributor listings reviewed for PCF8584P. Verify current declarations with NXP or the authorized supply source before production release.