Diodes Incorporated

PI7C9X1170BBLEX - 33Mbps I2C/SPI to UART Bridge | Diodes

MPN: PI7C9X1170BBLEX ✓ Aktif
Low; exact value not stated in the manufacturer result Id 16-pin TSSOP Package
MOQ: 1 |

PI7C9X1170BBLEX Ringkasan

Diodes Incorporated PI7C9X1170BBLEX is an I2C-bus/SPI to single-channel high-performance UART bridge controller designed for data rates up to 33 Mbps. The device also provides up to 8 programmable general-purpose I/O pins and is packaged in a compact 16-pin TSSOP.

An I2C/SPI-to-UART bridge controller is an interface IC that translates serial commands and data between a host processor and an asynchronous UART peripheral. In the system hierarchy, this device belongs to interface controllers, which sit between embedded processors and external communication equipment. Its dual-host-bus capability allows a system to configure or monitor a UART-connected device through either I2C or SPI without duplicating peripheral interfaces on the host.

The PI7C9X1170 supports serial transfer rates up to 33 Mbps and is intended for high-performance, cost-efficient handheld and battery-powered equipment. Its I2C/SPI host side is complemented by one UART channel, while as many as 8 programmable GPIO pins can support discrete control or status functions. The manufacturer describes the controller as having low operating and sleeping current, making power management an important part of the design rationale.

The compact 16-pin TSSOP package reduces board area compared with larger interface devices and is suitable for space-constrained embedded systems. The PI7C9X1170 family belongs to the broader category of interface ICs and bridges host-side control traffic with UART communication. Its single-channel architecture simplifies board routing when only one external UART endpoint is required.

Typical uses include handheld equipment, battery-operated instruments, industrial controllers, and embedded accessories that need to add a UART port to an I2C- or SPI-based processor. The bridge can consolidate command, configuration, and monitoring traffic over the processor's existing bus while the UART channel handles a dedicated peripheral connection. Programmable GPIO pins can extend status or control capability without requiring additional host I/O.

Designers should confirm protocol timing, logic levels, baud-rate configuration, and sleep-current behavior in the manufacturer datasheet before assigning pins. Because this is a high-speed interface device, short signal routes, stable supply decoupling, and careful grounding are important for maintaining signal integrity. The 16-pin TSSOP footprint also allows relatively compact routing between the host bus, UART channel, and programmable I/O.

This product page combines the manufacturer interface description, exact orderable MPN, package information, application guidance, and verified drop-in alternatives. It also highlights the engineering decisions involved in host-bus selection, power management, signal routing, and replacement qualification.

Pilihan pengganti yang segera untuk PI7C9X1170BBLEX — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera PI7C9X1170BBLEX (sama faktor bentuk dan kaki).

Tiada pilihan pengganti yang segera untuk produk ini.

Minta Alternatif

PI7C9X1170BBLEX Penilaian maksimum & Ciri-ciri Elektrik

Product Type I2C-bus/SPI to single-channel UART bridge controller
Maximum Data Rate 33 Mbps
Host Interface I2C-bus and SPI
UART Channel Count 1 channel
Programmable GPIO Count Up to 8 pins
Kemasan 16-pin TSSOP
Terminal Count 16 terminals
Package Shape Rectangular
Lead Form Gull wing
Jenis Pemasangan Surface mount
Temperature Grade Industrial
Sleeping Current Low; exact value not stated in the manufacturer result

Panduan Konfigurasi Pin PI7C9X1170BBLEX rectangular

Konfigurasi pin untuk PI7C9X1170BBLEX (rectangular pakai). Peranti kuasa ini mempunyai terminal kawat, buang, dan sumber. Untuk pakai non-polarized, rujuk dokumen pengeluar untuk orientasi pin 1 tepat dan perincian kebentuk.

Garis bentuk pengecah pakai rectangular untuk PI7C9X1170BBLEX

Tiada data garisan pin yang diperoleh untuk PI7C9X1170BBLEX.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

PI7C9X1170BBLEX patut untuk 6 aplikasis: Battery-Powered Handheld Instruments, Industrial Sensor and Controller Networking, Embedded Data Acquisition Modules, Programmable Control and GPIO Expansion, Communication Adapters and Gateways, Portable Medical and Diagnostic Equipment.

📱

Battery-Powered Handheld Instruments

The PI7C9X1170BBLEX fits handheld and battery-powered instruments that need a UART connection without allocating a dedicated UART peripheral in the host controller. Its I2C/SPI host interface lets the processor configure the bridge through an existing bus, while the single UART channel carries the external serial link. Operation up to 33 Mbps and low operating and sleeping current are useful for compact, power-conscious designs. The 16-pin TSSOP also limits board area, although the system designer should verify sleep-state current, wake timing, and supply requirements against the manufacturer datasheet before finalizing the power budget.

🏭

Industrial Sensor and Controller Networking

The PI7C9X1170BBLEX can bridge a microcontroller-based industrial controller to a UART-equipped sensor, actuator, or service interface. The host processor communicates through I2C or SPI, reducing the need for direct parallel control lines, while the bridge supplies one dedicated UART path. Its support for data rates up to 33 Mbps provides margin for burst-oriented industrial equipment. Up to 8 programmable GPIO pins can handle discrete enable, status, or alarm functions. For factory systems, confirm logic thresholds, isolation requirements, operating-temperature limits, and grounding before connecting external equipment.

📟

Embedded Data Acquisition Modules

In a compact data-acquisition module, the PI7C9X1170BBLEX allows a host processor to manage a UART-connected converter or measurement peripheral over I2C or SPI. The bridge consolidates configuration, status, and data-transfer control without requiring a separate UART block in the processor. A throughput ceiling of 33 Mbps makes the device suitable for systems that exchange bursts of command and response data. The industrial-grade package designation and low sleep current are useful where equipment spends substantial time idle, although calibration, isolation, and signal-conditioning requirements remain external to this interface controller.

🔧

Programmable Control and GPIO Expansion

The PI7C9X1170BBLEX is suitable for systems that need both a UART endpoint and additional discrete control signals. A host processor can use I2C or SPI for configuration, communicate with a UART peripheral through the bridge, and use the controller's up to 8 programmable GPIO pins for enables, interlocks, indicators, or status inputs. This integration reduces the number of host-controller pins required compared with implementing a UART and separate GPIO expansion. Pin directions, electrical limits, and switching behavior should be selected using the manufacturer pin-description and electrical-characteristics tables.

🌐

Communication Adapters and Gateways

The PI7C9X1170BBLEX can be used in protocol adapters where a central I2C- or SPI-based processor must service a UART-based downstream device. The single-channel bridge preserves a standard serial path while allowing configuration traffic to share the host bus. Its 16-pin TSSOP package is practical for compact adapters, and the stated 33-Mbps capability supports high-throughput links when the peripheral and electrical design can operate at that rate. Designers should evaluate protocol framing, baud-rate generation, clock requirements, and isolation before choosing the bridge for a new gateway architecture.

💊

Portable Medical and Diagnostic Equipment

The PI7C9X1170BBLEX can support portable diagnostic equipment that uses a UART-connected sensor or instrument while the main controller uses I2C or SPI. The bridge adds a serial endpoint and up to 8 programmable GPIO pins without requiring another large peripheral package, helping preserve the compact form factor of handheld equipment. Its low operating and sleeping current support battery-focused designs. Medical-system designs still require separate verification of accuracy-related timing, isolation, electrical safety, and regulatory requirements; this controller manages digital interfacing and does not provide those safety functions.

What is the PI7C9X1170BBLEX?
The PI7C9X1170BBLEX is a single-channel UART bridge controller that connects an I2C-bus or SPI host to an asynchronous UART peripheral. According to the Diodes Incorporated datasheet, the device supports data rates up to 33 Mbps and includes up to 8 programmable GPIO pins. It is supplied in a compact 16-pin TSSOP package.
What data rate does the PI7C9X1170BBLEX support?
The PI7C9X1170BBLEX supports serial data rates up to 33 Mbps. The Diodes Incorporated datasheet describes the PI7C9X1170 family as a high-performance I2C-bus/SPI to single-channel UART bridge controller. Exact UART baud-rate limits, I2C timing, and SPI operating modes should be confirmed in the electrical characteristics and timing tables.
Which interfaces does the PI7C9X1170BBLEX provide?
The PI7C9X1170BBLEX provides an I2C-bus or SPI host interface on the processor side and one UART channel on the peripheral side. It also offers up to 8 programmable general-purpose I/O pins. This combination allows an embedded host to supervise or configure a UART peripheral without dedicating a separate UART controller to that task.
Where can I download the PI7C9X1170BBLEX datasheet PDF?
The official PI7C9X1170BBLEX datasheet PDF is available from Diodes Incorporated at https://www.diodes.com/datasheet/download/PI7C9X1170.pdf. Use the pin-description table, electrical characteristics, timing diagrams, and application information in that document when assigning connections and validating signal and power requirements.
Where can I find the PI7C9X1170BBLEX pinout?
The PI7C9X1170BBLEX uses a 16-pin TSSOP package, and its complete pin assignments appear in the manufacturer datasheet. Use the pin-description table and package drawing to map the I2C/SPI host interface, UART channel, programmable GPIO pins, power rails, and ground connections before laying out the PCB.
What package does PI7C9X1170BBLEX use?
The PI7C9X1170BBLEX is supplied in a 16-pin TSSOP package with gull-wing leads and a rectangular surface-mount form. The manufacturer identifies the device as a high-performance bridge controller suitable for compact handheld and battery-powered equipment. Its small footprint helps conserve board area but requires careful signal routing.
Can PI7C9X1170BBLEX be used in a battery-powered device?
Yes, the PI7C9X1170BBLEX is suitable for battery-powered and handheld equipment when its sleep behavior matches the system power budget. The manufacturer specifically describes low operating and sleeping current as key benefits of the PI7C9X1170 family. Validate the exact current levels and required operating states in the manufacturer datasheet.
Where can I buy PI7C9X1170BBLEX online?
The PI7C9X1170BBLEX can be requested for quotation through the Request a Quote form on this page. Submit the exact orderable MPN PI7C9X1170BBLEX and state the required quantity, production packaging, and shipment destination so the request can be reviewed against the requested configuration.
What is the price of PI7C9X1170BBLEX?
Current commercial pricing for PI7C9X1170BBLEX is obtained through the Request a Quote form on this page. Submit the exact MPN, quantity, and packaging requirements to receive a current quotation. The form avoids presenting a static unit-price table that could become stale between production and procurement.
What is the lead time for PI7C9X1170BBLEX?
The current lead time for PI7C9X1170BBLEX should be requested through the Request a Quote form on this page. Include the required order quantity, production packaging, target delivery date, and any traceability requirements so the manufacturer or authorized channel can confirm availability and scheduling.
Is PI7C9X1170BBLEX in stock?
PI7C9X1170BBLEX inventory should be confirmed through the Request a Quote form on this page. The form accepts the exact MPN and requested quantity, allowing stock, lead time, and production-packaging options to be checked for the current procurement request rather than relying on a potentially outdated availability label.
What can replace PI7C9X1170BBLEX?
No confirmed pin-compatible drop-in replacement for PI7C9X1170BBLEX is identified in the available cross-reference results. A suitable replacement must match the 16-pin TSSOP footprint, I2C/SPI host interface, UART electrical behavior, GPIO assignment, supply requirements, and timing characteristics. Do not treat a general bridge-controller substitute as drop-in without pin-by-pin validation.
Is PI7C9X1170BBLEX the same as PI7C9X1170BBLE?
PI7C9X1170BBLEX and PI7C9X1170BBLE identify order variants of the PI7C9X1170 controller family, but the available results do not provide a complete suffix-code comparison. The exact MPN should be checked against the manufacturer ordering table for package, packing, and qualification differences before treating the two order codes as interchangeable.
What is the best equivalent for PI7C9X1170BBLEX?
No cross-manufacturer equivalent can be selected responsibly from the available cross-reference results because no candidate is confirmed as pin-to-pin compatible. A valid equivalent must retain the 16-pin TSSOP footprint, I2C/SPI host interface, single UART channel, up to 8 GPIO pins, and the required 33-Mbps-class performance. Verify the pin map and timing behavior before substitution.
When should I choose PI7C9X1170BBLEX over another UART bridge?
Choose PI7C9X1170BBLEX when an embedded system needs one UART channel controlled through I2C or SPI, up to 8 programmable GPIO pins, operation up to 33 Mbps, and a compact 16-pin TSSOP footprint. It is particularly useful in handheld or battery-powered equipment where preserving host-controller I/O and board area matters. Select another bridge when a different channel count, wider voltage range, or alternative package is required.
What are the key specifications of PI7C9X1170BBLEX that engineers should know?
The PI7C9X1170BBLEX combines an I2C/SPI host interface, one UART channel, up to 8 programmable GPIO pins, and operation up to 33 Mbps in a 16-pin TSSOP package. According to the Diodes Incorporated datasheet, the controller emphasizes low operating and sleeping current for compact and battery-powered systems. Supply voltage, exact baud-rate limits, and timing values require confirmation from the manufacturer electrical tables.

Data referensi kejuruteraan untuk PI7C9X1170BBLEX — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose PI7C9X1170BBLEX when the host processor uses I2C or SPI, the system needs one UART endpoint, and board area is constrained by a 16-pin TSSOP footprint. It is especially attractive for handheld, portable, and industrial equipment that can benefit from up to 8 programmable GPIO pins and low operating and sleeping current. Do not select it when multiple UART channels, a different supply range, or a larger package is required. No confirmed drop-in substitute is identified, so replacement decisions should be based on a complete review of the TSSOP-16 pin map, host-bus timing, UART behavior, GPIO functions, electrical limits, and power states. A functionally similar bridge controller may require software changes even if its nominal protocol and speed look similar.

Perbandingan dengan Gantian

Parametr Produk Ini
Brand Diodes Incorporated
Package 16-pin TSSOP
Product Type I2C-bus/SPI to single-channel UART bridge controller
Maximum Data Rate 33 Mbps
Host Interface I2C-bus and SPI
UART Channel Count 1 channel
Programmable GPIO Count Up to 8 pins
Temperature Grade Industrial
Mounting Type Surface mount

Penyeberangsung Jelas

  • Single-chip combination of I2C/SPI control and UART connectivity (vsA general-purpose interface controller without a confirmed UART channel)
  • High serial-performance capability (vsA lower-rate bridge-controller substitute)
  • Compact system-integration footprint (vsA larger-package equivalent)
  • Power-aware architecture (vsA bridge controller with higher sleep-state consumption)

Catatan Desain

Route the I2C, SPI, and UART signals with short, controlled-impedance paths and avoid unnecessary stubs. The manufacturer identifies operation up to 33 Mbps, so clock distribution, rise and fall times, ground return paths, and series damping must be evaluated together. Place decoupling capacitors close to the device's supply and ground pins, and keep high-current return currents out of the sensitive interface region.

Establish the normal, idle, and sleep-state power budget before committing the device to a battery-powered design. The PI7C9X1170 is described as having low operating and sleeping current, but the exact values and state-transition conditions must be taken from the manufacturer electrical tables. Include external pull-up requirements, I2C bus loading, UART-level loading, and peripheral leakage when comparing the complete system's current consumption.

Use the manufacturer TSSOP-16 land pattern and maintain the documented pad geometry and solder-mask rules. Keep the UART and host-bus escape paths short, and place any required pull-up or termination components where they can be adjusted during prototype testing. Confirm the exposed-versus-nonexposed thermal-pad configuration and the exact pin map on the PI7C9X1170 ordering table before releasing the PCB files.

Do not substitute a generic I2C/SPI-to-UART bridge based only on protocol description. Verify the 16-pin TSSOP footprint, pin functions, supply range, timing, GPIO count, UART baud-rate range, and reset or enable requirements. Also check whether the host uses clock stretching, chip-select conventions, or interrupt signaling not specified for the PI7C9X1170; these details determine whether a replacement is genuinely pin-to-pin compatible.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The exact compliance declarations are not stated in the manufacturer result. The industrial temperature-grade designation is identified for PI7C9X1170BBLEX.

Pencarian Berhubungan

PI7C9X1170BBLEX datasheet PI7C9X1170BBLEX pinout PI7C9X1170BBLEX datasheet pdf PI7C9X1170BBLEX equivalent PI7C9X1170BBLEX replacement PI7C9X1170BBLEX TSSOP-16 PI7C9X1170 33Mbps UART bridge PI7C9X1170BBLEX price PI7C9X1170BBLEX stock Diodes Incorporated PI7C9X1170BBLEX PI7C9X1170 I2C SPI UART controller PI7C9X1170BBLEX application circuit

Komponen dan Tanda berkaitan

Diodes Incorporated PI7C9X1170BBLEX PI7C9X1170 PI7C9X1170BBLE I2C-bus/SPI to UART bridge interface controller interface IC semiconductor UART I2C SPI general-purpose I/O GPIO 33 Mbps TSSOP-16 TSSOP package family surface-mount package handheld equipment battery-powered equipment industrial controller programmable GPIO sleep current signal integrity serial interface
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ