PI7C9X1170BBLEX - 33Mbps I2C/SPI to UART Bridge | Diodes
부품 번호: PI7C9X1170BBLEX ✓ 활성PI7C9X1170BBLEX 개요
An I2C/SPI-to-UART bridge controller is an interface IC that translates serial commands and data between a host processor and an asynchronous UART peripheral. In the system hierarchy, this device belongs to interface controllers, which sit between embedded processors and external communication equipment. Its dual-host-bus capability allows a system to configure or monitor a UART-connected device through either I2C or SPI without duplicating peripheral interfaces on the host.
The PI7C9X1170 supports serial transfer rates up to 33 Mbps and is intended for high-performance, cost-efficient handheld and battery-powered equipment. Its I2C/SPI host side is complemented by one UART channel, while as many as 8 programmable GPIO pins can support discrete control or status functions. The manufacturer describes the controller as having low operating and sleeping current, making power management an important part of the design rationale.
The compact 16-pin TSSOP package reduces board area compared with larger interface devices and is suitable for space-constrained embedded systems. The PI7C9X1170 family belongs to the broader category of interface ICs and bridges host-side control traffic with UART communication. Its single-channel architecture simplifies board routing when only one external UART endpoint is required.
Typical uses include handheld equipment, battery-operated instruments, industrial controllers, and embedded accessories that need to add a UART port to an I2C- or SPI-based processor. The bridge can consolidate command, configuration, and monitoring traffic over the processor's existing bus while the UART channel handles a dedicated peripheral connection. Programmable GPIO pins can extend status or control capability without requiring additional host I/O.
Designers should confirm protocol timing, logic levels, baud-rate configuration, and sleep-current behavior in the manufacturer datasheet before assigning pins. Because this is a high-speed interface device, short signal routes, stable supply decoupling, and careful grounding are important for maintaining signal integrity. The 16-pin TSSOP footprint also allows relatively compact routing between the host bus, UART channel, and programmable I/O.
This product page combines the manufacturer interface description, exact orderable MPN, package information, application guidance, and verified drop-in alternatives. It also highlights the engineering decisions involved in host-bus selection, power management, signal routing, and replacement qualification.
드롭인 대체품: PI7C9X1170BBLEX — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: PI7C9X1170BBLEX (동일 폼 팩터 및 풋프린트).
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청PI7C9X1170BBLEX 최대 정격 & 전기적 특성
| Product Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33 Mbps |
| Host Interface | I2C-bus and SPI |
| UART Channel Count | 1 channel |
| Programmable GPIO Count | Up to 8 pins |
| 패키지 | 16-pin TSSOP |
| Terminal Count | 16 terminals |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| 실장 유형 | Surface mount |
| Temperature Grade | Industrial |
| Sleeping Current | Low; exact value not stated in the manufacturer result |
PI7C9X1170BBLEX rectangular 핀 구성 가이드
PI7C9X1170BBLEX(rectangular 패키지)의 핀 구성입니다. 이 전력 소자는 게이트, 드레인, 소스 단자를 갖추고 있습니다. 비편향 패키지의 경우 정확한 핀 1 방향과 풋프린트 세부 정보는 제조사 데이터시트를 참조하십시오. 일반적인 응용 분야로는 전원 공급 장치 설계, 모터 구동, 부하 스위칭이 있습니다.
다음에 대한 상세 핀아웃 데이터 없음: PI7C9X1170BBLEX.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
PI7C9X1170BBLEX 적합 용도: 6 애플리케이션s: Battery-Powered Handheld Instruments, Industrial Sensor and Controller Networking, Embedded Data Acquisition Modules, Programmable Control and GPIO Expansion, Communication Adapters and Gateways, Portable Medical and Diagnostic Equipment.
Battery-Powered Handheld Instruments
The PI7C9X1170BBLEX fits handheld and battery-powered instruments that need a UART connection without allocating a dedicated UART peripheral in the host controller. Its I2C/SPI host interface lets the processor configure the bridge through an existing bus, while the single UART channel carries the external serial link. Operation up to 33 Mbps and low operating and sleeping current are useful for compact, power-conscious designs. The 16-pin TSSOP also limits board area, although the system designer should verify sleep-state current, wake timing, and supply requirements against the manufacturer datasheet before finalizing the power budget.
Industrial Sensor and Controller Networking
The PI7C9X1170BBLEX can bridge a microcontroller-based industrial controller to a UART-equipped sensor, actuator, or service interface. The host processor communicates through I2C or SPI, reducing the need for direct parallel control lines, while the bridge supplies one dedicated UART path. Its support for data rates up to 33 Mbps provides margin for burst-oriented industrial equipment. Up to 8 programmable GPIO pins can handle discrete enable, status, or alarm functions. For factory systems, confirm logic thresholds, isolation requirements, operating-temperature limits, and grounding before connecting external equipment.
Embedded Data Acquisition Modules
In a compact data-acquisition module, the PI7C9X1170BBLEX allows a host processor to manage a UART-connected converter or measurement peripheral over I2C or SPI. The bridge consolidates configuration, status, and data-transfer control without requiring a separate UART block in the processor. A throughput ceiling of 33 Mbps makes the device suitable for systems that exchange bursts of command and response data. The industrial-grade package designation and low sleep current are useful where equipment spends substantial time idle, although calibration, isolation, and signal-conditioning requirements remain external to this interface controller.
Programmable Control and GPIO Expansion
The PI7C9X1170BBLEX is suitable for systems that need both a UART endpoint and additional discrete control signals. A host processor can use I2C or SPI for configuration, communicate with a UART peripheral through the bridge, and use the controller's up to 8 programmable GPIO pins for enables, interlocks, indicators, or status inputs. This integration reduces the number of host-controller pins required compared with implementing a UART and separate GPIO expansion. Pin directions, electrical limits, and switching behavior should be selected using the manufacturer pin-description and electrical-characteristics tables.
Communication Adapters and Gateways
The PI7C9X1170BBLEX can be used in protocol adapters where a central I2C- or SPI-based processor must service a UART-based downstream device. The single-channel bridge preserves a standard serial path while allowing configuration traffic to share the host bus. Its 16-pin TSSOP package is practical for compact adapters, and the stated 33-Mbps capability supports high-throughput links when the peripheral and electrical design can operate at that rate. Designers should evaluate protocol framing, baud-rate generation, clock requirements, and isolation before choosing the bridge for a new gateway architecture.
Portable Medical and Diagnostic Equipment
The PI7C9X1170BBLEX can support portable diagnostic equipment that uses a UART-connected sensor or instrument while the main controller uses I2C or SPI. The bridge adds a serial endpoint and up to 8 programmable GPIO pins without requiring another large peripheral package, helping preserve the compact form factor of handheld equipment. Its low operating and sleeping current support battery-focused designs. Medical-system designs still require separate verification of accuracy-related timing, isolation, electrical safety, and regulatory requirements; this controller manages digital interfacing and does not provide those safety functions.
엔지니어링 참조 데이터: PI7C9X1170BBLEX — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Brand | Diodes Incorporated |
| Package | 16-pin TSSOP |
| Product Type | I2C-bus/SPI to single-channel UART bridge controller |
| Maximum Data Rate | 33 Mbps |
| Host Interface | I2C-bus and SPI |
| UART Channel Count | 1 channel |
| Programmable GPIO Count | Up to 8 pins |
| Temperature Grade | Industrial |
| Mounting Type | Surface mount |
주요 차별점
- Single-chip combination of I2C/SPI control and UART connectivity (vs A general-purpose interface controller without a confirmed UART channel)
- High serial-performance capability (vs A lower-rate bridge-controller substitute)
- Compact system-integration footprint (vs A larger-package equivalent)
- Power-aware architecture (vs A bridge controller with higher sleep-state consumption)
설계 노트
Route the I2C, SPI, and UART signals with short, controlled-impedance paths and avoid unnecessary stubs. The manufacturer identifies operation up to 33 Mbps, so clock distribution, rise and fall times, ground return paths, and series damping must be evaluated together. Place decoupling capacitors close to the device's supply and ground pins, and keep high-current return currents out of the sensitive interface region.
Establish the normal, idle, and sleep-state power budget before committing the device to a battery-powered design. The PI7C9X1170 is described as having low operating and sleeping current, but the exact values and state-transition conditions must be taken from the manufacturer electrical tables. Include external pull-up requirements, I2C bus loading, UART-level loading, and peripheral leakage when comparing the complete system's current consumption.
Use the manufacturer TSSOP-16 land pattern and maintain the documented pad geometry and solder-mask rules. Keep the UART and host-bus escape paths short, and place any required pull-up or termination components where they can be adjusted during prototype testing. Confirm the exposed-versus-nonexposed thermal-pad configuration and the exact pin map on the PI7C9X1170 ordering table before releasing the PCB files.
Do not substitute a generic I2C/SPI-to-UART bridge based only on protocol description. Verify the 16-pin TSSOP footprint, pin functions, supply range, timing, GPIO count, UART baud-rate range, and reset or enable requirements. Also check whether the host uses clock stretching, chip-select conventions, or interrupt signaling not specified for the PI7C9X1170; these details determine whether a replacement is genuinely pin-to-pin compatible.
규정 준수 정보
The exact compliance declarations are not stated in the manufacturer result. The industrial temperature-grade designation is identified for PI7C9X1170BBLEX.