PIC24EP64MC203-I/M5 - 70 MIPS 64KB Motor Control MCU | Microchip
MPN: PIC24EP64MC203-I/M5 ✓ AktifPIC24EP64MC203-I/M5 Ringkasan
A microcontroller is an integrated semiconductor containing a processor core, program memory, data memory, and peripherals such as timers, communication interfaces, and analog converters. A motor-control MCU extends that general purpose by adding high-speed PWM generation, fault-handling resources, and analog signal conditioning close to the control loop. The PIC24EP series sits within the broader 16-bit embedded-control hierarchy and reduces the component count needed for closed-loop motor regulation.
Key device resources include 64 KB of Flash, 8 KB of SRAM, and a maximum instruction throughput of 70 MIPS. The MCPWM block supports deterministic motor-commutation timing, while the integrated operational amplifiers can condition current-sense and feedback signals without external amplifiers. The Programmable Test Gauge provides additional on-chip measurement and test capability. A 3.3 V operating supply and an exposed-pad VTLA package support compact, thermally conscious PCB layouts.
The PIC24EP64MC203-I/M5 is specifically oriented to precision motor control. Its 16-bit architecture provides greater arithmetic headroom than an 8-bit MCU, and the high-speed PWM peripherals reduce the interrupt and software burden associated with generating motor drive waveforms. Because the operating voltage is fixed at 3.3 V in the published specification, the device fits 3.3 V logic systems and low-voltage motor-control power trees without a higher-voltage internal core requirement.
Typical uses include BLDC and stepper motor controllers, servo amplifiers, pump and fan drives, closed-loop position control, and compact power-conversion systems. Its small 5 mm by 5 mm footprint is valuable where the control board competes for space with the power stage. The exposed thermal pad also provides a direct heat-flow path when the motor driver dissipates power or drives frequent current-loop updates.
For PCB implementation, reserve a solid ground plane and place the exposed pad on a low-impedance copper region with a thermal-via array. Keep analog current-sense routing short and isolated from PWM drive nodes. Confirm motor transients and switching-node coupling before finalizing component spacing, because the 3.3 V supply domain can be disturbed by high dV/dt transitions even when the MCU itself operates from regulated power.
This page consolidates the verified device specifications, package information, drop-in replacement candidates, application guidance, and design checks into one engineering reference. It also identifies where MCU-specific details require confirmation in the manufacturer datasheet, including exact pin assignments, peripheral limits, and programming-tool configuration.
Pilihan pengganti yang segera untuk PIC24EP64MC203-I/M5 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera PIC24EP64MC203-I/M5 (sama faktor bentuk dan kaki) — berbeza dalam Operating Temperature Range, ADC, Package.
PIC24EP64MC203-E/M5
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →PIC24EP64MC203-I/SP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
PIC24EP64MC203-I/ML
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
PIC24EP64MC203-I/M5
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →PIC24EP64MC203-E/SP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
PIC24EP64MC203-I/M5 Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 16-bit PIC24EP motor-control microcontroller |
| Maximum Instruction Throughput | 70 MIPS |
| Program Flash Memory | 64 KB (22K x 24 words) |
| Static RAM | 8 KB |
| Motor-Control PWM | MCPWM module |
| Integrated Analog | Operational amplifiers |
| Test and Measurement Peripheral | Programmable Test Gauge (PTG) |
| Tegangan Pemberi Arus Operasi | 3.3 V |
| Gambaran Suhu Operasi | -40 °C to +85 °C |
| Package Type | 36-pin VTLA with exposed pad |
| Package Dimensions | 5 mm x 5 mm |
| Architecture | 16-bit PIC24EP |
| Program Memory Type | Flash |
| Jenis Pemasangan | Surface mount |
| Maximum GPIO Count | 25 I/O pins |
| Interrupt Sources | 52 sources |
| Trap Count | 7 traps |
Panduan Konfigurasi Pin PIC24EP64MC203-I/M5 5 mm x 5 mm
Konfigurasi pin untuk PIC24EP64MC203-I/M5 (5 mm x 5 mm pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk PIC24EP64MC203-I/M5.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
PIC24EP64MC203-I/M5 patut untuk 6 aplikasis: BLDC Motor Controller, Stepper Motor Position Control, Servo and Robotics Actuator Control, Pump and Fan Speed Control, Low-Voltage Power Converter Control, Programmable Test and Measurement.
BLDC Motor Controller
The PIC24EP64MC203-I/M5 fits compact brushless DC motor drives because its 70 MIPS execution rate leaves processing headroom for current sampling, commutation logic, and control updates between PWM events. The dedicated MCPWM module provides deterministic high-speed PWM generation for the inverter stage, while the integrated operational amplifiers can help condition current-sense feedback. The 36-pin, 5 mm by 5 mm VTLA package also allows the controller to sit close to the power stage, although PWM nodes must remain isolated from the analog inputs.
Disebarkan
Stepper Motor Position Control
The PIC24EP64MC203-I/M5 is suitable for stepper-motor position and microstepping controllers where position feedback and precise PWM timing are required. Its 16-bit architecture and 70 MIPS throughput support step-generation routines, closed-loop position calculations, and motion-profile interpolation. The MCPWM peripherals provide synchronized outputs, and the 8 KB of SRAM can hold motion parameters and control variables. Firmware should verify the exact PWM-to-stepper-driver interface and pin multiplexing in the manufacturer pin table.
Disebarkan
Servo and Robotics Actuator Control
Compact robotic actuators benefit from the PIC24EP64MC203-I/M5 because the MCU combines control processing, analog amplification, and programmable PWM output in one 5 mm by 5 mm package. A 70 MIPS core can execute a current or position loop while the MCPWM block maintains deterministic actuator drive timing. The integrated operational amplifiers can support current-sense conditioning, and the Programmable Test Gauge assists with production diagnostics. The exposed pad must be tied to a thermal-via structure to carry heat away from the controller.
Disebarkan
Pump and Fan Speed Control
The PIC24EP64MC203-I/M5 supports efficient pump and fan drives that need variable-speed control, current monitoring, and compact board area. Its MCPWM output can generate the required motor-drive waveform, while the operational amplifiers can reduce the analog front-end count for current or voltage feedback. The 3.3 V supply integrates easily with low-voltage gate drivers, and the -40 °C to +85 °C grade suits equipment operating across a wide industrial ambient range.
Disebarkan
Low-Voltage Power Converter Control
The PIC24EP64MC203-I/M5 can serve as the supervisory and digital-control element in a compact low-voltage power converter. Its 70 MIPS performance permits fast loop updates, and the integrated operational amplifiers can assist with feedback conditioning around a power stage. The MCPWM resources support synchronized switching and dead-time management when the board uses a dedicated gate driver. Because the MCU operates from 3.3 V, the design must keep switching-node transients and the high-power return path out of the analog reference network.
Disebarkan
Programmable Test and Measurement
The Programmable Test Gauge and integrated operational amplifiers make the PIC24EP64MC203-I/M5 applicable to production-test fixtures and embedded measurement systems. The 70 MIPS core can execute stimulus sequences and analyze results, while the 64 KB of Flash provides room for test programs and calibration data. Eight kilobytes of SRAM supports working buffers, and the small 36-pin VTLA package simplifies placement in automated test equipment. The PTG configuration and measurement limits should be confirmed in the manufacturer datasheet.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk PIC24EP64MC203-I/M5 — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | PIC24EP64MC203-E/M5 | PIC24EP64MC203-I/SP | PIC24EP64MC203-I/ML | PIC24EP64MC203-E/SP |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 36-pin VTLA (5x5) with exposed pad | 36-pin VTLA (5x5) with exposed pad | 36-pin VTLA (5x5) with exposed pad | 36-pin VTLA (5x5) with exposed pad | 36-pin VTLA (5x5) with exposed pad |
| Architecture | 16-bit PIC24EP | 16-bit PIC24EP | 16-bit PIC24EP | 16-bit PIC24EP | 16-bit PIC24EP |
| Maximum Instruction Throughput | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS | 70 MIPS |
| Program Flash Memory | 64 KB (22K x 24 words) | 64 KB | 64 KB | 64 KB | 64 KB |
| Static RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| Motor-Control PWM | MCPWM module | MCPWM module | MCPWM module | MCPWM module | MCPWM module |
| Integrated Analog and Test Resources | Operational amplifiers and Programmable Test Gauge | Operational amplifiers and Programmable Test Gauge | Operational amplifiers and Programmable Test Gauge | Operational amplifiers and Programmable Test Gauge | Operational amplifiers and Programmable Test Gauge |
| Operating Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
Penyeberangsung Jelas
- Dedicated motor-control integration in a compact package (vsPIC24EP64MC203-E/M5)
- Industrial-temperature ordering matches typical controlled enclosures (vsPIC24EP64MC203-E/M5)
- Pin-compatible thermal and electrical platform (vsPIC24EP64MC203-I/SP)
Catatan Desain
Treat the VTLA exposed pad as the principal thermal path rather than an optional pad. Place a continuous copper region beneath the package and distribute it into a grid of thermal vias, while keeping via inductance low. Avoid placing a keep-out on the pad or splitting the ground plane directly below the MCU. Validate the assembled junction temperature with the package thermal data and the actual board copper area.
Separate the 3.3 V analog and digital return paths as far as practical from high-current motor and switching-node returns. Route current-sense signals as short, tightly controlled traces and ground them with a continuous reference plane. Place decoupling capacitors close to the device supply pins, and verify the recommended values and stability criteria in the manufacturer datasheet before tuning the compensation network.
Do not assume that every PIC24EP64MC203 ordering code is interchangeable without checking its grade, package, and operating limits. The -I/M5 part is the industrial option, while -E/M5 uses the extended-temperature code. Also verify that the exposed pad is connected as directed; treating it as a mechanical feature can degrade thermal performance and invalidate the recommended land pattern.
Maklumat Kesediaan
The -I/M5 ordering code identifies an industrial-temperature device, but no explicit RoHS, REACH, halogen-free or conflict-minerals declaration appears in the manufacturer or distributor listing. Confirm the current declarations and material-compliance documentation with Microchip before qualification.