SI3056-KS - Global Serial Interface DAA | Silicon Labs
MPN: SI3056-KS ✗ Akhir HayatSI3056-KS Ringkasan
A direct access arrangement is a telephone-interface IC that places the analog line-coupling, codec, isolation, and control functions into one programmable device. In the broader hierarchy, a DAA belongs to the interface-IC family and is used with a host processor or serial communications controller. Instead of using discrete telephone-interface components, a system can configure line termination, transmit and receive gains, ring detection, and codec behavior through registers. This integration is particularly useful in voice-over-data equipment, VoIP terminals, embedded telephony systems, and caller-ID products.
The SI3056’s principal engineering benefit is reduced implementation complexity. The integrated codec and four-wire-hybrid support, patented isolation technology, and programmable line interface can remove several external circuit blocks. The 80 dB TX/RX dynamic range supports voice-band operation while giving the designer a defined signal-chain range. Programmable AC termination and DC termination accommodate different line conditions, while programmable ring detection and ringer impedance make the same device adaptable across multiple telephone-network requirements.
The SI3056 family uses a serial host interface for configuration and control. Firmware must correctly initialize line impedance, gain, termination, ring-detection thresholds, and codec settings before enabling the line path. Host-side software should also handle Type I and Type II caller ID if that feature is required. Because the device is intended to bridge a digital system to an analog telephone line, PCB isolation, grounding, creepage, surge exposure, and regulatory testing remain important system-level considerations even though the component integrates isolation circuitry.
Typical uses include Voice over IP endpoint hardware, analog telephone adapters, fax and multifunction-printer line interfaces, caller-ID equipment, and embedded voice gateways. The SI3056 is also suitable when an existing product needs a programmable replacement for several discrete line-interface blocks. Integration can shorten assembly time and reduce component count, but engineers must still validate line-side protection, ringing behavior, codec quality, and regional network requirements in the complete product.
The principal design consideration is to treat the SI3056-KS as a controlled line-side subsystem rather than a generic codec. Follow the manufacturer datasheet for pin connections, isolation boundaries, termination settings, ring-detection configuration, and external protection components. Avoid adding unverified network-interface protection between the device and the telephone line because it can alter impedance and signaling behavior. Validate the assembled design across line lengths, off-hook states, ring voltage conditions, and caller-ID modes.
Pilihan pengganti yang segera untuk SI3056-KS — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
SI3056-FS
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →SI3056-KS Spesifikasi
| Product Type | Global Serial Interface Direct Access Arrangement (DAA) |
| Telephone Line Interface | Programmable global telephone line interface |
| Kiraan Pin | 16 pins |
| Kemasan | 16-pin small outline package |
| TX/RX Dynamic Range | 80 dB |
| AC Termination | Programmable |
| DC Termination | Programmable |
| Ring Detection Threshold | Programmable |
| Ringer Impedance | Programmable |
| Codec Integration | Integrated codec and up to 4-wire hybrid |
| Caller ID Support | Type I and Type II |
| Isolation Technology | Skyworks Solutions patented isolation technology |
| External AFE Requirement | Eliminated |
| Isolation Transformer Requirement | Eliminated |
| Relay and Optoisolator Requirement | Eliminated |
Panduan Konfigurasi Pin SI3056-KS 16-pin small outline package
Konfigurasi pin untuk SI3056-KS (16-pin small outline package pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk SI3056-KS.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
SI3056-KS patut untuk 6 aplikasis: Voice over IP Telephony Terminals, Analog Telephone Adapters, Caller ID Terminals, Embedded Voice Gateways, Multifunction Printer Fax Modules, Telephone Test and Measurement Equipment.
Voice over IP Telephony Terminals
The SI3056-KS fits a VoIP terminal because it combines a programmable telephone-line interface, integrated codec, and up to a four-wire hybrid in one 16-pin device. The 80 dB TX/RX dynamic range provides a defined voice-band signal range, while programmable AC and DC termination allows the host software to accommodate different line conditions. Placing it beside the network processor reduces the need for a discrete analog front end, isolation transformer, relays, and optoisolators. The principal tradeoff is that host firmware must initialize termination, gain, ring detection, and caller-ID functions correctly before the line path is enabled.
Disebarkan
Analog Telephone Adapters
The SI3056-KS is appropriate for an analog telephone adapter requiring a programmable line side without a large collection of discrete components. Its integrated codec and telephone-line termination functions reduce PCB area, while the patented isolation technology replaces the external isolation transformer described in the manufacturer datasheet. The 80 dB TX/RX dynamic range supports ordinary voice traffic, and programmable ring detection helps the adapter identify incoming calls. Designers should still verify off-hook impedance, ring-voltage handling, line protection, and country-specific network behavior in the complete adapter.
Disebarkan
Caller ID Terminals
SI3056-KS supports Type I and Type II caller ID, making it suitable for telephone terminals that decode incoming caller information. The integrated codec handles the voice path while programmable AC termination, DC termination, ring detection, and ringer impedance allow the terminal to adapt to the active line. Its 80 dB dynamic range provides useful transmit and receive headroom for voice-band signaling. Firmware must enable the correct caller-ID mode and coordinate ring detection with the decoder because incorrect configuration can cause missed or noisy identification results.
Disebarkan
Embedded Voice Gateways
The SI3056-KS can provide the analog line endpoint in an embedded voice gateway that bridges legacy telephone service to digital signaling. Integrating the codec, four-wire-hybrid support, termination, and isolation reduces the analog peripheral count around an embedded processor. This is particularly valuable when the gateway must support programmable line impedance or caller ID. The design must carefully partition the line-side circuitry, use the manufacturer-recommended protection and layout approach, and verify ring detection and voice quality over representative line lengths and network conditions.
Disebarkan
Multifunction Printer Fax Modules
The SI3056-KS can support a fax or multifunction-printer telephone module by combining the line interface and codec in a compact 16-pin package. Programmable termination and ring detection let the printer controller handle incoming calls, while 80 dB dynamic range covers the voice and modem-band requirements described by the manufacturer. Replacing an isolation transformer and several discrete interface blocks can reduce assembly cost and board area. Production validation should include dialing, answer supervision, ring-voltage handling, caller ID if required, and repeated line-connect operations.
Disebarkan
Telephone Test and Measurement Equipment
SI3056-KS can serve as a programmable line-interface element in telephone test equipment because termination, ring-detection threshold, and ringer impedance are configurable rather than hardwired. The integrated codec and 80 dB TX/RX dynamic range provide a repeatable voice-path test interface, while programmable line behavior helps reproduce different subscriber-line conditions. For production or laboratory fixtures, the same device can simplify the analog front end. Engineers should calibrate the test limits and verify that the host automation applies the intended termination, ring, and caller-ID configurations before each measurement.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk SI3056-KS — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | SI3056-FS |
|---|---|---|
| Package | 16-pin small outline package | 16-pin small outline package; exact KS/FS dimensions require manufacturer confirmation |
| Brand | Silicon Labs | Silicon Labs |
| Product Type | Global serial interface direct access arrangement | SI3056-family direct access arrangement |
Penyeberangsung Jelas
- Integrates multiple telephone-line front-end blocks (vsSI3056-FS)
- Programmable line termination and ringing behavior (vsSI3056-FS)
- Integrated caller-ID capability (vsSI3056-FS)
Catatan Desain
Follow the manufacturer isolation, grounding, and pin-layout guidance exactly; the SI3056 integrates isolation but does not eliminate PCB partitioning requirements. Keep the telephone-line-side routing separated from host and digital ground domains according to the datasheet, and avoid long copper areas or test pads that can compromise isolation behavior. Because no verified numbered pinout was supplied, do not infer pad locations from the generic 16-pin package drawing; use the official KS-package diagram before routing.
Program the line termination, ring detection, ringer impedance, and codec gain only after the host power rails and serial interface are stable. Confirm the device-specific supply limits and sequencing requirements from the manufacturer datasheet because no operating-voltage range was included in the verified data. Changing line termination during an active call can create transients or alter the subscriber-line load, so use the manufacturer’s supported register sequence and allow settling time before enabling the voice path.
Do not treat the SI3056 as a general-purpose audio codec or assume that any equivalent-family suffix is automatically interchangeable. The verified material identifies programmable line behavior and Type I/Type II caller ID, but it does not provide the exact KS pinout, limits, or a quantified cross-reference table. Validate line protection, off-hook behavior, ring-voltage tolerance, caller-ID modes, and firmware initialization on the assembled product before production release.
Maklumat Kesediaan
The verified web results do not contain RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is marked not_applicable because this is a telecommunications interface IC rather than an automotive-qualified product, but the other statuses remain unknown.
