SN74HC365N - Hex 3-State Bus Buffer Driver | Texas Instruments
MPN: SN74HC365N ✓ AktifSN74HC365N Ringkasan
A 3-state buffer is a digital logic device that can actively drive a HIGH level, actively drive a LOW level, or disconnect its output from the bus. The SN74HC365N uses this capability to support bus-oriented receivers, transmitters, memory-address drivers, and clock drivers. When the output-enable input is inactive, all six outputs become high impedance and allow other devices to share the same bus without electrical contention.
The HC logic family provides CMOS-compatible operation with low power consumption and improved noise margins compared with older TTL logic families. The manufacturer describes the SN74HC365 as a 6-channel buffer and line driver with 2 V to 6 V operation, wide operating-voltage range, high-current 3-state outputs, and bus-line drive capability. The non-inverting architecture preserves input polarity at each output.
Use the SN74HC365N when a system needs multiple tristate drivers on a shared parallel bus, particularly for memory address registers, clock distribution, data-bus isolation, or bidirectional transceiver front ends. The 3-state outputs allow multiple drivers to be connected to the same net only when their enable states are controlled so that no two devices drive the same node simultaneously.
In a practical design, connect the output-enable pin to a decoder, control logic, or bus-arbitration signal. Ensure every driver on the shared bus has a defined output state during reset and power-up. Check the enable timing against the propagation delay of the surrounding logic so that a new driver does not enable while another driver is still releasing the bus.
The SN74HC365N is suited to industrial-control, instrumentation, test-equipment, embedded-computing, and general digital-interface designs. For designs that need a different package, a different voltage family, or a bidirectional data path, select a device whose pinout and electrical ratings explicitly match the PCB footprint and system requirements.
This page combines manufacturer product information, distributor listings, drop-in alternatives, and application-focused design guidance for engineers evaluating the SN74HC365N.
Pilihan pengganti yang segera untuk SN74HC365N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
SN74HC365NE4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
SN74HC365N Penilaian maksimum & Ciri-ciri Elektrik
| Device Type | Hex buffer and line driver |
| Number of Channels | 6 |
| Logic Level | HC CMOS |
| Supply Voltage Range | 2 V to 6 V |
| Konfigurasi Output | 6-bit, 3-state, non-inverting |
| Output Enable | Common output-enable control |
| Output Drive | High-current 3-state outputs |
| Input Type | CMOS-compatible |
| Propagation Delay | Typical tpd; exact value not stated in the product-page data |
| Arus Pemberi Arus | 80 uA maximum typical ICC |
| Gambaran Suhu Operasi | -40 °C to 85 °C |
| Kemasan | 16-pin PDIP (N) |
| Jenis Pemasangan | Through-hole |
| Operating Voltage | 2 V to 6 V |
| Output State | High, low, or high impedance |
| Bus Application | Memory address, clock, receiver, and transmitter bus driving |
Konfigurasi Pin SN74HC365N
| Pin 1 | 1A — Data input for channel 1 |
| Pin 2 | 1Y — 3-state output for channel 1 |
| Pin 3 | 2A — Data input for channel 2 |
| Pin 4 | 2Y — 3-state output for channel 2 |
| Pin 5 | 3A — Data input for channel 3 |
| Pin 6 | 3Y — 3-state output for channel 3 |
| Pin 7 | GND — Ground reference |
| Pin 8 | OE — Common output enable for the six outputs |
| Pin 9 | 4Y — 3-state output for channel 4 |
| Pin 10 | 4A — Data input for channel 4 |
| Pin 11 | 5Y — 3-state output for channel 5 |
| Pin 12 | 5A — Data input for channel 5 |
| Pin 13 | 6Y — 3-state output for channel 6 |
| Pin 14 | 6A — Data input for channel 6 |
| Pin 15 | VCC — Positive supply voltage |
| Pin 16 | NC — Not connected |
Aplikasi Biasa
SN74HC365N patut untuk 6 aplikasis: Memory Address Bus Drivers, Clock Signal Isolation and Distribution, Data Bus Isolation, Industrial Control and Instrumentation, Test and Measurement Systems, Embedded System Bus Fan-Out.
Memory Address Bus Drivers
The SN74HC365N is well suited to driving multiplexed memory-address lines in systems where several address sources must share one bus. Its six non-inverting channels provide buffered address paths, while the common 3-state enable can isolate the bank whenever another address driver becomes active. The 2 V to 6 V operating range supports both modern low-voltage control logic and legacy 5 V interfaces. The important design condition is exclusive bus ownership: decoded enable signals should guarantee that no two enabled drivers source conflicting levels onto the same address conductor.
Disebarkan
Clock Signal Isolation and Distribution
When a clock must connect to one of several receivers without permanently loading the source, the SN74HC365N can place its six outputs into the high-impedance state until the intended clock domain is selected. Its non-inverting buffer paths preserve clock polarity and provide a common enable for coordinated switching. The design should be checked for propagation-delay skew between channels and for clock-edge requirements if the source operates at high frequency. Use the manufacturer's timing data to establish whether the device is suitable for the target clock rate.
Disebarkan
Data Bus Isolation
The SN74HC365N can isolate a six-bit data segment from a shared bus by driving the segment actively or disconnecting all six outputs. This arrangement is useful in systems with multiple buffer banks, test fixtures, and card-edge interfaces where only one participant should control the bus at a time. The common enable simplifies bank selection, but the enable must be synchronized with the data source and bus owner. A safe design also defines output states during reset so that the part cannot contend with another driver while the control logic is initializing.
Disebarkan
Industrial Control and Instrumentation
The SN74HC365N fits 16-pin through-hole control boards that require a small number of buffered, selectable bus outputs. Its -40 °C to 85 °C rating supports industrial temperature conditions, and the HC CMOS supply range allows operation across several logic levels. It can drive address-select, module-select, or test-enable lines in programmable instrumentation. Layout should maintain short traces on high-speed nets, provide a stable ground reference, and keep the shared-bus enable away from long unprotected routes that could pick up noise during switching.
Disebarkan
Test and Measurement Systems
In test equipment, the SN74HC365N can connect buffered control signals to a shared fixture or internal bus while keeping unused sections electrically disconnected. Six channels and one common enable reduce the number of discrete control gates required for a multi-section driver arrangement. Because test fixtures often contain long cables and slower edges, the device's 3-state outputs help prevent unused drivers from loading the bus. Confirm output-state behavior at power-up and use a defined reset strategy before connecting an external fixture that may contain its own drivers.
Disebarkan
Embedded System Bus Fan-Out
The SN74HC365N can fan out a six-bit control or address word to a local bus section when a processor or programmable controller must gain drive strength without continuously loading the source. The 3-state outputs permit temporary connection to a shared conductor, and the non-inverting channels preserve the original logic polarity. The part's 2 V to 6 V range is useful when interfacing a modern controller with 5 V peripheral logic, subject to the datasheet's input thresholds and output-level limits. Confirm that the selected supply voltage supports the system's level requirements.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk SN74HC365N — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | SN74HC365NE4 |
|---|---|---|
| Package | 16-pin PDIP (N) | 16-pin PDIP (N) |
| Brand | Texas Instruments | Texas Instruments |
| Device Function | Hex buffer and line driver with 3-state outputs | Hex buffer and line driver with 3-state outputs |
| Number of Channels | 6 | 6 |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V |
| Output Configuration | Non-inverting, 3-state | Non-inverting, 3-state |
| Operating Temperature Range | -40 °C to 85 °C | -40 °C to 85 °C |
| Mounting Type | Through-hole | Through-hole |
Penyeberangsung Jelas
- Six independent non-inverting channels with one common 3-state enable (vsSN74HC365NE4)
- Wide HC CMOS supply-voltage operation (vsSN74HC365NE4)
- Common enable simplifies six-channel bus ownership (vsSN74HC365NE4)
Catatan Desain
Ensure that only one driver is enabled on a shared bus at a time. The SN74HC365N has a common output-enable input, so a simple decoding error can place two devices in opposite output states and create direct contention. Define the enable state during power-up and reset, and use the manufacturer timing information to verify that the outgoing driver has released the bus before the incoming driver begins driving.
Operate the device only within its 2 V to 6 V supply range and account for CMOS dynamic current as well as static supply current. Place a local bypass capacitor close to the VCC and GND pins, using the manufacturer's recommended decoupling value where specified. Because all six outputs can be active simultaneously, assess the available supply current and board-level thermal performance for a bus driver operating continuously across all channels.
Route the six data lines and the common output-enable as short, direct traces, and keep the enable away from sources of asynchronous switching noise. Provide a low-impedance ground return for the PDIP device and avoid long stubs on bus connections. Because the package uses through-hole leads, check lead spacing and insertion tooling against the PCB footprint before release, and use the TI pin-description table to verify every net during schematic review.
Maklumat Kesediaan
The available manufacturer-page information confirms the SN74HC365 family, 2 V to 6 V operation, 16-pin PDIP N-package, and -40 °C to 85 °C rating. It does not provide explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statements, so those fields remain unknown rather than assumed.