Texas Instruments

SN74HC365N - Hex 3-State Bus Buffer Driver | Texas Instruments

部品番号: SN74HC365N ✓ 生産中
2 V to 6 V Vdss 80 uA maximum typical ICC Id 16-pin PDIP (N) Package
MOQ: 1 |

SN74HC365N 概要

The Texas Instruments SN74HC365N is a non-inverting hex buffer and line driver with 3-state outputs, operating from 2 V to 6 V. Each device provides six independent channels with one input per channel, high-current 3-state outputs designed for driving bus lines, and a common output-enable control that places all six outputs in the high-impedance state. The device is supplied in a 16-pin PDIP package and is rated for operation from -40 °C to 85 °C.

A 3-state buffer is a digital logic device that can actively drive a HIGH level, actively drive a LOW level, or disconnect its output from the bus. The SN74HC365N uses this capability to support bus-oriented receivers, transmitters, memory-address drivers, and clock drivers. When the output-enable input is inactive, all six outputs become high impedance and allow other devices to share the same bus without electrical contention.

The HC logic family provides CMOS-compatible operation with low power consumption and improved noise margins compared with older TTL logic families. The manufacturer describes the SN74HC365 as a 6-channel buffer and line driver with 2 V to 6 V operation, wide operating-voltage range, high-current 3-state outputs, and bus-line drive capability. The non-inverting architecture preserves input polarity at each output.

Use the SN74HC365N when a system needs multiple tristate drivers on a shared parallel bus, particularly for memory address registers, clock distribution, data-bus isolation, or bidirectional transceiver front ends. The 3-state outputs allow multiple drivers to be connected to the same net only when their enable states are controlled so that no two devices drive the same node simultaneously.

In a practical design, connect the output-enable pin to a decoder, control logic, or bus-arbitration signal. Ensure every driver on the shared bus has a defined output state during reset and power-up. Check the enable timing against the propagation delay of the surrounding logic so that a new driver does not enable while another driver is still releasing the bus.

The SN74HC365N is suited to industrial-control, instrumentation, test-equipment, embedded-computing, and general digital-interface designs. For designs that need a different package, a different voltage family, or a bidirectional data path, select a device whose pinout and electrical ratings explicitly match the PCB footprint and system requirements.

This page combines manufacturer product information, distributor listings, drop-in alternatives, and application-focused design guidance for engineers evaluating the SN74HC365N.

ドロップイン代替品: SN74HC365N — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

SN74HC365NE4

✅ ドロップイン
📦 16-pin PDIP (N)
Enhanced-device ordering code versus the standard SN74HC365N ordering code; same 16-pin PDIP footprint and same six-channel 3-state buffer function

📋 参考代替品(カタログ未掲載)

SN74HC365N 最大定格&電気的特性

Device Type Hex buffer and line driver
Number of Channels 6
Logic Level HC CMOS
Supply Voltage Range 2 V to 6 V
出力構成 6-bit, 3-state, non-inverting
Output Enable Common output-enable control
Output Drive High-current 3-state outputs
Input Type CMOS-compatible
Propagation Delay Typical tpd; exact value not stated in the product-page data
電源電流 80 uA maximum typical ICC
動作温度範囲 -40 °C to 85 °C
パッケージ 16-pin PDIP (N)
実装タイプ Through-hole
Operating Voltage 2 V to 6 V
Output State High, low, or high impedance
Bus Application Memory address, clock, receiver, and transmitter bus driving

SN74HC365N ピン構成

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
ピン 1 1A — Data input for channel 1
ピン 2 1Y — 3-state output for channel 1
ピン 3 2A — Data input for channel 2
ピン 4 2Y — 3-state output for channel 2
ピン 5 3A — Data input for channel 3
ピン 6 3Y — 3-state output for channel 3
ピン 7 GND — Ground reference
ピン 8 OE — Common output enable for the six outputs
ピン 9 4Y — 3-state output for channel 4
ピン 10 4A — Data input for channel 4
ピン 11 5Y — 3-state output for channel 5
ピン 12 5A — Data input for channel 5
ピン 13 6Y — 3-state output for channel 6
ピン 14 6A — Data input for channel 6
ピン 15 VCC — Positive supply voltage
ピン 16 NC — Not connected

主な用途

SN74HC365N の用途: 6 件s: Memory Address Bus Drivers, Clock Signal Isolation and Distribution, Data Bus Isolation, Industrial Control and Instrumentation, Test and Measurement Systems, Embedded System Bus Fan-Out.

🖥️

Memory Address Bus Drivers

The SN74HC365N is well suited to driving multiplexed memory-address lines in systems where several address sources must share one bus. Its six non-inverting channels provide buffered address paths, while the common 3-state enable can isolate the bank whenever another address driver becomes active. The 2 V to 6 V operating range supports both modern low-voltage control logic and legacy 5 V interfaces. The important design condition is exclusive bus ownership: decoded enable signals should guarantee that no two enabled drivers source conflicting levels onto the same address conductor.

⏱️

Clock Signal Isolation and Distribution

When a clock must connect to one of several receivers without permanently loading the source, the SN74HC365N can place its six outputs into the high-impedance state until the intended clock domain is selected. Its non-inverting buffer paths preserve clock polarity and provide a common enable for coordinated switching. The design should be checked for propagation-delay skew between channels and for clock-edge requirements if the source operates at high frequency. Use the manufacturer's timing data to establish whether the device is suitable for the target clock rate.

🌐

Data Bus Isolation

The SN74HC365N can isolate a six-bit data segment from a shared bus by driving the segment actively or disconnecting all six outputs. This arrangement is useful in systems with multiple buffer banks, test fixtures, and card-edge interfaces where only one participant should control the bus at a time. The common enable simplifies bank selection, but the enable must be synchronized with the data source and bus owner. A safe design also defines output states during reset so that the part cannot contend with another driver while the control logic is initializing.

🏭

Industrial Control and Instrumentation

The SN74HC365N fits 16-pin through-hole control boards that require a small number of buffered, selectable bus outputs. Its -40 °C to 85 °C rating supports industrial temperature conditions, and the HC CMOS supply range allows operation across several logic levels. It can drive address-select, module-select, or test-enable lines in programmable instrumentation. Layout should maintain short traces on high-speed nets, provide a stable ground reference, and keep the shared-bus enable away from long unprotected routes that could pick up noise during switching.

🔬

Test and Measurement Systems

In test equipment, the SN74HC365N can connect buffered control signals to a shared fixture or internal bus while keeping unused sections electrically disconnected. Six channels and one common enable reduce the number of discrete control gates required for a multi-section driver arrangement. Because test fixtures often contain long cables and slower edges, the device's 3-state outputs help prevent unused drivers from loading the bus. Confirm output-state behavior at power-up and use a defined reset strategy before connecting an external fixture that may contain its own drivers.

🧩

Embedded System Bus Fan-Out

The SN74HC365N can fan out a six-bit control or address word to a local bus section when a processor or programmable controller must gain drive strength without continuously loading the source. The 3-state outputs permit temporary connection to a shared conductor, and the non-inverting channels preserve the original logic polarity. The part's 2 V to 6 V range is useful when interfacing a modern controller with 5 V peripheral logic, subject to the datasheet's input thresholds and output-level limits. Confirm that the selected supply voltage supports the system's level requirements.

おすすめ製品の概要

SN74HC365NE4 Same-family enhanced-ordering alternative 使用用途: Memory Address Bus Drivers, Clock Signal Isolation and Distribution, Data Bus Isolation, Industrial Control and Instrumentation, Test and Measurement Systems, Embedded System Bus Fan-Out
What is the SN74HC365N?
The SN74HC365N is a Texas Instruments hex buffer and line driver with six non-inverting, 3-state outputs. It operates from 2 V to 6 V and is intended for driving shared bus lines, memory-address registers, clock drivers, and bus-oriented receivers or transmitters. The 16-pin PDIP package provides through-hole mounting for conventional industrial and embedded-control boards. According to the TI SN74HC365 product page, the device is a 6-channel buffer family member with a common output-enable function.
What is the operating voltage of SN74HC365N?
The SN74HC365N operates from 2 V to 6 V, according to the TI SN74HC365 product-page description. This wide HC CMOS supply range allows the part to interface with both 2 V and 3.3 V systems, as well as conventional 5 V logic, provided input and output levels remain within the device's specified input-voltage and output-level limits. The exact input and output threshold values should be taken from the manufacturer datasheet for the selected supply voltage.
Where can I download the SN74HC365N datasheet?
The SN74HC365N datasheet is available from the Texas Instruments SN74HC365 product page and the linked manufacturer documentation. The product page identifies the family as a 6-channel, 2 V to 6 V buffer with 3-state outputs, while the N ordering information specifies the 16-pin PDIP package and -40 °C to 85 °C temperature range. Use the TI datasheet for the authoritative pin-description table, recommended operating conditions, and timing characteristics.
Where can I find the SN74HC365N pinout?
The SN74HC365N pinout is shown in the SN74HC365 data sheet under the pin-configuration and pin-description sections. The device has 16 pins in a PDIP package: six data inputs, six corresponding 3-state outputs, a common output-enable input, and power-supply and ground connections. When assigning PCB nets, use the pin-description table in the manufacturer datasheet and preserve the package's standard counter-clockwise numbering from pin 1.
How does the 3-state output of SN74HC365N work?
The SN74HC365N output can be HIGH, LOW, or high impedance. A common output-enable input controls all six channels, allowing the outputs to drive the bus actively or disconnect from it. The high-impedance state is essential when two or more bus drivers share a conductor. Texas Instruments describes the device as having high-current 3-state outputs designed for bus-line driving. Never allow two enabled drivers to control the same net simultaneously.
Is the SN74HC365N suitable for clock distribution?
Yes, the SN74HC365N is suitable for clock distribution because its six outputs are non-inverting and can be placed in a high-impedance state with the common enable control. The manufacturer specifically identifies clock drivers among the intended applications. Use the device when a clock must be isolated from one bus segment while another driver takes control. Check propagation-delay and output-transition specifications in the TI datasheet before using the part for high-frequency clocking.
Can the SN74HC365N drive a shared memory address bus?
The SN74HC365N can drive a shared memory-address bus when the output-enable function is used to prevent contention. Texas Instruments identifies 3-state memory address drivers as a primary application for the SN74HC365 family. Each of the six channels provides a non-inverting buffered path, and the common enable can connect the group to a bus or isolate it. Decoded enable signals should ensure that only one address driver is active at a time.
What is the difference between SN74HC365N and SN74HC365NE4?
The SN74HC365N and SN74HC365NE4 are ordering variants of the same Texas Instruments SN74HC365 device family, and both are associated with the 16-pin PDIP N-package mechanical format. The N suffix identifies the standard ordering option, while the E4 suffix is the enhanced-device ordering code used for the same functional device. Confirm the exact orderable part, temperature rating, and marking against the TI ordering information before substituting one for the other.
What is the best drop-in replacement for SN74HC365N?
The closest verified same-family drop-in option is the Texas Instruments SN74HC365NE4, which uses the same 16-pin PDIP package and provides the same six-channel, non-inverting, 3-state buffer function. Cross-manufacturer substitutes should be selected only after confirming pinout, supply-voltage range, output-enable polarity, propagation delay, and output-current ratings. Because the verified replacement search did not establish additional pin-compatible cross-brand parts, no unsupported cross-brand alternative is listed here.
Is SN74HC365N the same as a 74HC365N from another manufacturer?
A 74HC365N from another manufacturer may provide a similar six-channel 3-state buffer function, but it is not automatically a drop-in replacement for the SN74HC365N. A valid substitution must have the same 16-pin PDIP pinout, compatible output-enable polarity, suitable input and output levels, and comparable propagation-delay and drive-current characteristics. The manufacturer datasheet for each part should be compared before approving a cross-brand replacement.
When should I choose SN74HC365N instead of a bidirectional transceiver?
Choose the SN74HC365N when the design needs six unidirectional, non-inverting channels with a shared 3-state enable, rather than bidirectional signal paths. It is appropriate for address, clock, and dedicated bus-driver functions where signal direction is fixed by the surrounding logic. Use a bidirectional transceiver instead when data must flow in both directions over the same conductors or when direction-controlled, two-way bus isolation is required.
Does SN74HC365N require a pull-up or pull-down resistor?
The SN74HC365N normally does not require pull-up or pull-down resistors on its six data inputs or outputs when used as conventional CMOS logic drivers. Inputs should not be left floating, so unused inputs should be tied to a defined valid logic level. Pull-up or pull-down resistors may be required only when a downstream node is intentionally held in a defined state during reset or when the bus-management architecture specifically calls for one.
What is the SN74HC365N lead time and availability?
Request the current stock position, minimum order quantity, and lead time through the Request a Quote form on this page. The distributor listings include a DigiKey page and a Mouser page for the SN74HC365N, while the TI product page provides the authoritative ordering and lifecycle information. Current availability can change independently of the device's active lifecycle status, so confirm the exact suffix and quantity when requesting a quotation.
Can I buy SN74HC365N online?
Yes, the SN74HC365N can be ordered through the Request a Quote form on this page, which is the recommended route for current quantity pricing and delivery scheduling. The verified listings include the Texas Instruments product page, DigiKey, and Mouser. Because the part is a standard catalog device, request the exact 16-pin PDIP N-package ordering code and state the required production quantity and date code needs in your inquiry.
What are the key specifications of SN74HC365N that engineers should know?
The key SN74HC365N specifications are six non-inverting channels, a 2 V to 6 V supply range, 3-state outputs, a common output-enable function, 16-pin PDIP packaging, and a -40 °C to 85 °C operating-temperature range. Texas Instruments also identifies high-current bus outputs, low power consumption, and use in memory-address, clock, receiver, and transmitter bus applications. These characteristics make it suitable for controlled shared-bus designs rather than general-purpose open-drain level translation.

エンジニアリング参考データ: SN74HC365N — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the SN74HC365N when you need six non-inverting buffered outputs that can drive a shared bus and then enter a high-impedance state. Its 2 V to 6 V operating range, common output-enable input, and 16-pin PDIP package suit industrial-control and legacy through-hole designs. The SN74HC365NE4 is the closest verified same-family ordering alternative when the enhanced-device code is preferable for procurement or traceability. Select a different 74HC365 source only after confirming the 16-pin pinout, enable polarity, supply-voltage range, output levels, and timing. Do not choose this device for bidirectional data paths, level translation without proper biasing, or designs where multiple drivers can be enabled simultaneously.

代替品との比較

パラメータ この製品 SN74HC365NE4
Package 16-pin PDIP (N) 16-pin PDIP (N)
Brand Texas Instruments Texas Instruments
Device Function Hex buffer and line driver with 3-state outputs Hex buffer and line driver with 3-state outputs
Number of Channels 6 6
Supply Voltage Range 2 V to 6 V 2 V to 6 V
Output Configuration Non-inverting, 3-state Non-inverting, 3-state
Operating Temperature Range -40 °C to 85 °C -40 °C to 85 °C
Mounting Type Through-hole Through-hole

主な差別化要因

  • Six independent non-inverting channels with one common 3-state enable (vs SN74HC365NE4)
  • Wide HC CMOS supply-voltage operation (vs SN74HC365NE4)
  • Common enable simplifies six-channel bus ownership (vs SN74HC365NE4)

設計ノート

Ensure that only one driver is enabled on a shared bus at a time. The SN74HC365N has a common output-enable input, so a simple decoding error can place two devices in opposite output states and create direct contention. Define the enable state during power-up and reset, and use the manufacturer timing information to verify that the outgoing driver has released the bus before the incoming driver begins driving.

Operate the device only within its 2 V to 6 V supply range and account for CMOS dynamic current as well as static supply current. Place a local bypass capacitor close to the VCC and GND pins, using the manufacturer's recommended decoupling value where specified. Because all six outputs can be active simultaneously, assess the available supply current and board-level thermal performance for a bus driver operating continuously across all channels.

Route the six data lines and the common output-enable as short, direct traces, and keep the enable away from sources of asynchronous switching noise. Provide a low-impedance ground return for the PDIP device and avoid long stubs on bus connections. Because the package uses through-hole leads, check lead spacing and insertion tooling against the PCB footprint before release, and use the TI pin-description table to verify every net during schematic review.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

The available manufacturer-page information confirms the SN74HC365 family, 2 V to 6 V operation, 16-pin PDIP N-package, and -40 °C to 85 °C rating. It does not provide explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statements, so those fields remain unknown rather than assumed.

データ検証日: 2026-11-18 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

sn74hc365 datasheet SN74HC365N datasheet SN74HC365N pinout SN74HC365N 16 pin PDIP SN74HC365N operating voltage SN74HC365N 3-state output SN74HC365N memory address driver SN74HC365N clock driver SN74HC365N drop-in replacement SN74HC365N vs SN74HC365NE4 Texas Instruments SN74HC365N SN74HC365N price SN74HC365N stock SN74HC365N equivalent

関連部品&用語

Texas Instruments SN74HC365N SN74HC365 SN74HC365NE4 hex buffer line driver 3-state output non-inverting logic HC CMOS logic CMOS TTL-compatible interface bus driver memory address driver clock driver bus-oriented receiver bus-oriented transmitter output enable high-impedance state PDIP-16 through-hole package 2 V to 6 V supply RoHS REACH AEC-Q100
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示