SN74HC367N - 6-Channel 3-State Buffer | Texas Instruments
MPN: SN74HC367N ✓ AktifSN74HC367N Ringkasan
A hex buffer or line driver is a digital logic IC that strengthens input signals for transmission between circuit sections. In the broader hierarchy, it belongs to logic ICs, digital semiconductors, and bus-interface logic. Unlike a bidirectional transceiver, the SN74HC367N has dedicated inputs and outputs, so its signal direction remains fixed. Its three-state outputs add a third electrical condition—high impedance—besides the normal logic-high and logic-low states.
The key operating characteristics are its 2 V to 6 V supply range, six buffered channels, non-inverting logic operation, two independent output-enable controls, and three-state outputs. This organization makes it useful for memory-address driving, clock distribution, bus-oriented signal buffering, and systems that need one group of four drivers and another group of two drivers to share a bus selectively.
The SN74HC367 architecture separates the six drivers into banks so that related loads can be enabled together. When an output-enable input is asserted, the corresponding outputs enter the high-impedance state and stop actively driving the connected net. When the enable is deasserted, the buffer reproduces the corresponding input logic level at its output. The through-hole SN74HC367N ordering option is identified by the N package designation in the distributor listing.
Typical applications include microprocessor and microcontroller address buses, memory address lines, clock distribution, industrial control interfaces, and embedded systems that need increased drive capability. Using two independent enable banks allows a designer to connect a four-bit group and a two-bit group to shared resources, releasing one group while the other remains active.
PCB design should route each input to its corresponding output without unintended stubs and place a common ground reference close to the device. The power and ground pins should be connected with short traces, and signal transitions should be checked at the far end of the bus to verify that the selected driver and loading arrangement maintain valid logic levels.
This page organizes the device function, package details, sourcing information, and verified cross-reference candidates into a design-focused reference. It also identifies which replacement details require circuit-specific validation, helping engineers distinguish logical equivalence from guaranteed production interchangeability.
Pilihan pengganti yang segera untuk SN74HC367N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
SN54HC367N
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
74HC367N
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
MM70C97J/883
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
SN54HC367
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
SN74HC367N Penilaian maksimum & Ciri-ciri Elektrik
| Device Type | Hex buffer and line driver |
| Number of Channels | 6 channels |
| Logic Level | CMOS, 2 V to 6 V |
| Supply Voltage Range | 2 V to 6 V |
| Konfigurasi Output | 2 banks: 4 drivers and 2 drivers |
| Output Enable Control | 2 independent active-low output-enable inputs |
| Output State | 3-state, including high impedance |
| Logic Direction | Non-inverting |
| Input-to-Output Organization | 2 elements with 2-bit and 4-bit groups |
| Kemasan | 16-pin PDP through-hole package |
| Jenis Pemasangan | Through-hole |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Konfigurasi Pin SN74HC367N
| Pin 1 | 1A1 — Input for output 1 of the four-driver bank |
| Pin 2 | 1Y1 — Output 1 of the four-driver bank |
| Pin 3 | 2A1 — Input for output 2 of the four-driver bank |
| Pin 4 | 2Y1 — Output 2 of the four-driver bank |
| Pin 5 | 3A1 — Input for output 3 of the four-driver bank |
| Pin 6 | 3Y1 — Output 3 of the four-driver bank |
| Pin 7 | 4A1 — Input for output 4 of the four-driver bank |
| Pin 8 | 4Y1 — Output 4 of the four-driver bank |
| Pin 9 | 1OE — Active-low output enable for the four-driver bank |
| Pin 10 | GND — Ground reference |
| Pin 11 | 5A1 — Input for output 5 of the two-driver bank |
| Pin 12 | 5Y1 — Output 5 of the two-driver bank |
| Pin 13 | 6A1 — Input for output 6 of the two-driver bank |
| Pin 14 | 6Y1 — Output 6 of the two-driver bank |
| Pin 15 | 2OE — Active-low output enable for the two-driver bank |
| Pin 16 | VCC — Power supply |
Aplikasi Biasa
SN74HC367N patut untuk 6 aplikasis: Memory Address Bus Buffering, Clock Signal Distribution, Shared Industrial Bus Isolation, Microcontroller Interface Buffering, Legacy Data Acquisition Backplane, Embedded Control Signal Fanout.
Memory Address Bus Buffering
The SN74HC367N fits memory-address buffering because it provides six non-inverting channels and independent three-state control over a four-driver bank and a two-driver bank. Place the device between a processor or memory-controller output and the address lines of a memory device so the buffered signals reach the load with improved drive strength. Its 2 V to 6 V operating range supports common CMOS supply systems. The design should verify propagation delay, capacitive-load capability, and setup and hold margins in the manufacturer datasheet. The four-driver bank can address one group of devices while the two-driver bank controls another, reducing contention during shared-bus transitions.
Disebarkan
Clock Signal Distribution
The SN74HC367N can distribute clock signals to multiple loads while keeping inactive outputs in the high-impedance state. Its six non-inverting channels and two independent enable banks allow one clock source to feed selected destinations without tying together outputs that could otherwise contend. The 16-PDIP device is useful in through-hole industrial and legacy control equipment where a short clock path and straightforward rework are priorities. Validate clock rise time, fanout, capacitive loading, and timing skew at each receiver because buffer propagation delay contributes to the downstream clock budget.
Disebarkan
Shared Industrial Bus Isolation
The SN74HC367N is appropriate for shared industrial buses where two groups of receivers must be connected and released independently. Its four-driver bank and two-driver bank each have a dedicated active-low output-enable input, allowing one group to remain active while the other is disabled. The high-impedance state prevents the disabled drivers from fighting an active bus participant. For industrial equipment, confirm operating-temperature limits, isolation strategy, and fault behavior in the manufacturer datasheet. Keep enable timing outside the path where a transient could produce overlapping drive intervals, and use pull-down or pull-up resistors where required by the system interface specification.
Disebarkan
Microcontroller Interface Buffering
The SN74HC367N can add drive strength between a microcontroller or other CMOS controller and a connector, memory, or peripheral bus. Six dedicated non-inverting channels make it useful for address, control, or grouped data signals that need buffered transmission rather than bidirectional exchange. Its separate enable banks support partial bus participation, while its 2 V to 6 V supply range covers conventional embedded logic levels. The design must account for input capacitance, output drive current, propagation delay, and signal settling at the connector. Use short traces and a solid ground return to prevent the improvement in source drive strength from being offset by excessive board-level loading.
Disebarkan
Legacy Data Acquisition Backplane
The SN74HC367N fits legacy data-acquisition backplanes that require multiple unidirectional buffers with controlled bus participation. Two independently enabled output banks support segmented routing without sacrificing the three-state behavior expected by older bus architectures. The 16-PDIP package simplifies repair in equipment designed around through-hole logic boards. During design-in, verify that the 2 V to 6 V supply range matches the backplane, and compare the manufacturer timing and output-current data with the original device. Maintain defined logic states on disabled nets if downstream receivers do not include their own biasing, and account for lead time and long-term availability when maintaining an installed base.
Disebarkan
Embedded Control Signal Fanout
The SN74HC367N is useful for distributing unidirectional control and address signals inside embedded control systems. Its six channels can serve separate loads, and the two output banks allow related signals to be enabled as a group. This arrangement is particularly helpful when several subsystems share a communication or selection line and must not drive simultaneously. The buffered outputs retain the same logic polarity as their inputs, simplifying control logic. Confirm that the controller's source can meet the buffer input requirements and that each driven net remains within the manufacturer's specified load limits. Add suitable termination where long traces or cable connections are unavoidable, and verify startup states to prevent unintended high-impedance behavior.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk SN74HC367N — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | SN54HC367N | 74HC367N | MM70C97J/883 | SN54HC367 |
|---|---|---|---|---|---|
| Package | 16-PDIP | 16-PDIP | 16-PDIP | 16-PDIP | 16-PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | National Semiconductor | Texas Instruments |
| Number of Channels | 6 | 6 | 6 | 6 | 6 |
| Output Bank Organization | 4 drivers and 2 drivers | 4 drivers and 2 drivers | 4 drivers and 2 drivers | 4 drivers and 2 drivers | 4 drivers and 2 drivers |
| Output Enable Inputs | 2 independent active-low inputs | 2 independent active-low inputs | 2 independent active-low inputs | 2 independent active-low inputs | 2 independent active-low inputs |
| Output State | 3-state with high-impedance disable | 3-state with high-impedance disable | 3-state with high-impedance disable | 3-state with high-impedance disable | 3-state with high-impedance disable |
| Logic Polarity | Non-inverting | Non-inverting | Non-inverting | Non-inverting | Non-inverting |
Penyeberangsung Jelas
- Independently controlled four-driver and two-driver banks (vs74HC367N)
- Commercial-temperature ordering option (vsSN54HC367N)
- Current family documentation for design-in (vsMM70C97J/883)
Catatan Desain
Route each input directly to its associated output and keep the enable inputs away from high-speed switching nets to minimize coupling into output-enable timing. The DIP footprint provides generous routing flexibility, but input and output traces should still be short enough to limit ringing, crosstalk, and propagation-delay variation. Use a continuous ground plane or equivalent low-impedance return path so the six buffered outputs share an effective reference with the driven logic system.
Do not allow two enabled output channels to drive the same net with opposite logic states. The SN74HC367N uses three-state outputs, but the high-impedance condition does not automatically resolve a conflict between two active drivers. Interlock the two output-enable controls where multiple groups share a bus, and specify the required state of disabled nets so downstream receivers do not float during transitions or reset conditions.
Check the complete signal path against the manufacturer timing and output-current data, including input capacitance, trace capacitance, receiving-device input current, and propagation-delay margins. For longer traces or cable-connected loads, measure edge shape at the far endpoint rather than assuming nominal CMOS edge rates. If ringing causes additional settling time, reduce the load or add a source-series termination resistor selected from impedance and edge-rate analysis.
Place the device so that the supply and ground leads have short, low-impedance paths to the system rails. In a through-hole design, excessive lead length can create additional loop area and make switching-node coupling more likely. Confirm that the chosen socket, board, and assembly process support the 16-PDIP footprint, and inspect the seating plane for solder bridges between adjacent high-speed enable and data pins.
Maklumat Kesediaan
The supplied product listings identify the family and package but do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose commercial logic device.