Texas Instruments

SN74HC367N - 6-Channel 3-State Buffer | Texas Instruments

부품 번호: SN74HC367N ✓ 활성
2 V to 6 V Vdss 16-pin PDP through-hole package Package
MOQ: 1 |

SN74HC367N 개요

The Texas Instruments SN74HC367N is a six-channel non-inverting buffer and line driver with three-state outputs, operating from 2 V to 6 V and packaged in a 16-pin through-hole DIP. The device provides two independently controlled output banks: one four-driver bank and one two-driver bank. Each bank can place its outputs in a high-impedance state through its dedicated active-low output-enable input, allowing multiple devices to share a bus without contention.

A hex buffer or line driver is a digital logic IC that strengthens input signals for transmission between circuit sections. In the broader hierarchy, it belongs to logic ICs, digital semiconductors, and bus-interface logic. Unlike a bidirectional transceiver, the SN74HC367N has dedicated inputs and outputs, so its signal direction remains fixed. Its three-state outputs add a third electrical condition—high impedance—besides the normal logic-high and logic-low states.

The key operating characteristics are its 2 V to 6 V supply range, six buffered channels, non-inverting logic operation, two independent output-enable controls, and three-state outputs. This organization makes it useful for memory-address driving, clock distribution, bus-oriented signal buffering, and systems that need one group of four drivers and another group of two drivers to share a bus selectively.

The SN74HC367 architecture separates the six drivers into banks so that related loads can be enabled together. When an output-enable input is asserted, the corresponding outputs enter the high-impedance state and stop actively driving the connected net. When the enable is deasserted, the buffer reproduces the corresponding input logic level at its output. The through-hole SN74HC367N ordering option is identified by the N package designation in the distributor listing.

Typical applications include microprocessor and microcontroller address buses, memory address lines, clock distribution, industrial control interfaces, and embedded systems that need increased drive capability. Using two independent enable banks allows a designer to connect a four-bit group and a two-bit group to shared resources, releasing one group while the other remains active.

PCB design should route each input to its corresponding output without unintended stubs and place a common ground reference close to the device. The power and ground pins should be connected with short traces, and signal transitions should be checked at the far end of the bus to verify that the selected driver and loading arrangement maintain valid logic levels.

This page organizes the device function, package details, sourcing information, and verified cross-reference candidates into a design-focused reference. It also identifies which replacement details require circuit-specific validation, helping engineers distinguish logical equivalence from guaranteed production interchangeability.

드롭인 대체품: SN74HC367N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

SN54HC367N

✅ 드롭인
📦 16-PDIP
Six channels and three-state output counts are unchanged at 0% difference; the military-temperature ordering option is the principal distinction.

📋 참조 대체품 (카탈로그에 없음)

74HC367N

✅ 드롭인
📦 16-PDIP
Six buffered channels, two enable-controlled banks, and 3-state output behavior are unchanged at 0% difference; manufacturer-specific ordering and qualification details require review.

📋 참조 대체품 (카탈로그에 없음)

MM70C97J/883

✅ 드롭인
📦 16-PDIP
The six-channel logic function and three-state behavior are functionally unchanged at 0% difference; temperature grade, timing, and qualification may differ.

📋 참조 대체품 (카탈로그에 없음)

SN54HC367

✅ 드롭인
📦 16-PDIP
The six-channel and two-bank 3-state functions are unchanged at 0% difference; the military-temperature family ordering option differs from the commercial SN74HC367N.

📋 참조 대체품 (카탈로그에 없음)

SN74HC367N 최대 정격 & 전기적 특성

Device Type Hex buffer and line driver
Number of Channels 6 channels
Logic Level CMOS, 2 V to 6 V
Supply Voltage Range 2 V to 6 V
출력 구성 2 banks: 4 drivers and 2 drivers
Output Enable Control 2 independent active-low output-enable inputs
Output State 3-state, including high impedance
Logic Direction Non-inverting
Input-to-Output Organization 2 elements with 2-bit and 4-bit groups
패키지 16-pin PDP through-hole package
실장 유형 Through-hole
RoHS 상태 unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

SN74HC367N 핀 구성

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
핀 1 1A1 — Input for output 1 of the four-driver bank
핀 2 1Y1 — Output 1 of the four-driver bank
핀 3 2A1 — Input for output 2 of the four-driver bank
핀 4 2Y1 — Output 2 of the four-driver bank
핀 5 3A1 — Input for output 3 of the four-driver bank
핀 6 3Y1 — Output 3 of the four-driver bank
핀 7 4A1 — Input for output 4 of the four-driver bank
핀 8 4Y1 — Output 4 of the four-driver bank
핀 9 1OE — Active-low output enable for the four-driver bank
핀 10 GND — Ground reference
핀 11 5A1 — Input for output 5 of the two-driver bank
핀 12 5Y1 — Output 5 of the two-driver bank
핀 13 6A1 — Input for output 6 of the two-driver bank
핀 14 6Y1 — Output 6 of the two-driver bank
핀 15 2OE — Active-low output enable for the two-driver bank
핀 16 VCC — Power supply

일반적인 애플리케이션

SN74HC367N 적합 용도: 6 애플리케이션s: Memory Address Bus Buffering, Clock Signal Distribution, Shared Industrial Bus Isolation, Microcontroller Interface Buffering, Legacy Data Acquisition Backplane, Embedded Control Signal Fanout.

🖥️

Memory Address Bus Buffering

The SN74HC367N fits memory-address buffering because it provides six non-inverting channels and independent three-state control over a four-driver bank and a two-driver bank. Place the device between a processor or memory-controller output and the address lines of a memory device so the buffered signals reach the load with improved drive strength. Its 2 V to 6 V operating range supports common CMOS supply systems. The design should verify propagation delay, capacitive-load capability, and setup and hold margins in the manufacturer datasheet. The four-driver bank can address one group of devices while the two-driver bank controls another, reducing contention during shared-bus transitions.

⚡

Clock Signal Distribution

The SN74HC367N can distribute clock signals to multiple loads while keeping inactive outputs in the high-impedance state. Its six non-inverting channels and two independent enable banks allow one clock source to feed selected destinations without tying together outputs that could otherwise contend. The 16-PDIP device is useful in through-hole industrial and legacy control equipment where a short clock path and straightforward rework are priorities. Validate clock rise time, fanout, capacitive loading, and timing skew at each receiver because buffer propagation delay contributes to the downstream clock budget.

🏭

Shared Industrial Bus Isolation

The SN74HC367N is appropriate for shared industrial buses where two groups of receivers must be connected and released independently. Its four-driver bank and two-driver bank each have a dedicated active-low output-enable input, allowing one group to remain active while the other is disabled. The high-impedance state prevents the disabled drivers from fighting an active bus participant. For industrial equipment, confirm operating-temperature limits, isolation strategy, and fault behavior in the manufacturer datasheet. Keep enable timing outside the path where a transient could produce overlapping drive intervals, and use pull-down or pull-up resistors where required by the system interface specification.

🔧

Microcontroller Interface Buffering

The SN74HC367N can add drive strength between a microcontroller or other CMOS controller and a connector, memory, or peripheral bus. Six dedicated non-inverting channels make it useful for address, control, or grouped data signals that need buffered transmission rather than bidirectional exchange. Its separate enable banks support partial bus participation, while its 2 V to 6 V supply range covers conventional embedded logic levels. The design must account for input capacitance, output drive current, propagation delay, and signal settling at the connector. Use short traces and a solid ground return to prevent the improvement in source drive strength from being offset by excessive board-level loading.

📺

Legacy Data Acquisition Backplane

The SN74HC367N fits legacy data-acquisition backplanes that require multiple unidirectional buffers with controlled bus participation. Two independently enabled output banks support segmented routing without sacrificing the three-state behavior expected by older bus architectures. The 16-PDIP package simplifies repair in equipment designed around through-hole logic boards. During design-in, verify that the 2 V to 6 V supply range matches the backplane, and compare the manufacturer timing and output-current data with the original device. Maintain defined logic states on disabled nets if downstream receivers do not include their own biasing, and account for lead time and long-term availability when maintaining an installed base.

🧩

Embedded Control Signal Fanout

The SN74HC367N is useful for distributing unidirectional control and address signals inside embedded control systems. Its six channels can serve separate loads, and the two output banks allow related signals to be enabled as a group. This arrangement is particularly helpful when several subsystems share a communication or selection line and must not drive simultaneously. The buffered outputs retain the same logic polarity as their inputs, simplifying control logic. Confirm that the controller's source can meet the buffer input requirements and that each driven net remains within the manufacturer's specified load limits. Add suitable termination where long traces or cable connections are unavoidable, and verify startup states to prevent unintended high-impedance behavior.

추천 제품 요약

SN74HC367N Texas Instruments 사용처: Memory Address Bus Buffering, Clock Signal Distribution, Shared Industrial Bus Isolation, Microcontroller Interface Buffering, Legacy Data Acquisition Backplane, Embedded Control Signal Fanout 74HC367N Functionally comparable 74HC367 family option 사용처: Memory Address Bus Buffering, Microcontroller Interface Buffering SN54HC367N Temperature-range alternative for demanding systems 사용처: Clock Signal Distribution, Embedded Control Signal Fanout MM70C97J/883 Legacy functionally equivalent hex driver 사용처: Shared Industrial Bus Isolation SN54HC367 Military-temperature family option 사용처: Legacy Data Acquisition Backplane
What is the SN74HC367N and what does it do?
The SN74HC367N is a six-channel non-inverting CMOS buffer and line driver with three-state outputs. According to the Texas Instruments product page and manufacturer datasheet, it operates from 2 V to 6 V and divides its outputs into two independently enabled banks: one four-driver bank and one two-driver bank. Each bank can drive a bus normally or place its outputs in a high-impedance state for shared-bus operation.
How many output-enable inputs does the SN74HC367N have?
The SN74HC367N has two active-low output-enable inputs, one for its four-driver bank and one for its two-driver bank. The Texas Instruments manufacturer datasheet identifies this two-bank organization, with each bank independently controllable. Asserting an enable places only the associated outputs in the high-impedance state, allowing a four-bit group and a two-bit group to be connected to shared resources without simultaneous output contention.
What is the operating voltage of SN74HC367N?
The SN74HC367N operates from 2 V to 6 V. This range is stated on the Texas Instruments product page and in the manufacturer datasheet. The device is therefore suited to both low-voltage CMOS systems and conventional 5 V logic systems, although designers should use the datasheet timing and output-current limits applicable to the selected supply voltage.
What package is the SN74HC367N manufactured in?
The SN74HC367N is supplied in a 16-pin through-hole PDP package. The DigiKey manufacturer listing explicitly identifies the part as a 16-PDIP, while the Texas Instruments family datasheet covers the SN74HC367 device and its ordering options. The N designation identifies this through-hole ordering option, which differs from surface-mount versions that require a different PCB footprint.
Where can I download the SN74HC367N datasheet PDF?
The official SN74HC367 datasheet is available from Texas Instruments at https://www.ti.com/lit/gpn/SN74HC367. The manufacturer datasheet is the preferred source for the pin description, truth table, electrical characteristics, operating limits, and package information. Use it to confirm the exact SN74HC367N ordering details before assigning signals or designing a replacement board.
Where is the SN74HC367N pinout located?
The SN74HC367N pinout is shown in the pin-configuration section of the Texas Instruments SN74HC367 manufacturer datasheet. The 16-pin PDP package contains eight data inputs, eight corresponding outputs, two active-low output-enable inputs, one supply pin, and one ground pin. Consult that diagram when routing the two independently enabled output banks.
Where can I buy SN74HC367N and check its current lead time?
Use the Request a Quote form on this page to request SN74HC367N availability, current lead time, and order quantities. The request can specify the required 16-PDIP package and Tube or Bulk packaging preference. Commercial terms and inventory should be confirmed at the time of quotation because component availability can change with manufacturer production and distribution cycles.
What is the price of SN74HC367N?
The current SN74HC367N unit price is shown through the Request a Quote form on this page. Submit the required quantity and packaging preference to obtain an actionable quotation. This approach keeps pricing aligned with current market conditions rather than embedding a potentially stale price in technical documentation, and it also allows sourcing staff to confirm exact MPN, package, and delivery requirements.
Is SN74HC367N in stock?
Current SN74HC367N stock should be confirmed through the Request a Quote form on this page. Include the required quantity, 16-PDIP package, and preferred delivery schedule in the request. Because availability and lead time are transaction-specific, the confirmation should cover both the requested quantity and any acceptable manufacturing traceability requirements.
What can replace the SN74HC367N?
A replacement must preserve the 16-pin logic interface, six non-inverting channels, two independently controlled three-state output banks, and the intended supply-voltage range. Cross-reference candidates identified for the SN74HC367 include 74HC367N, SN54HC367N, and MM70C97J/883, but logical equivalence alone does not guarantee identical timing, temperature grade, or sourcing. Validate the manufacturer datasheet and board-level behavior before approving a substitution.
Can CD74HC367E replace SN74HC367N?
The CD74HC367E can provide the same six-channel buffer and two-bank three-state function, but it is not an automatic footprint-identical replacement for the SN74HC367N. The CD74HC367E ordering option is associated with a surface-mount package, whereas the SN74HC367N is specified as a 16-PDIP through-hole part. A PCB change or a verified through-hole equivalent is therefore required before considering it a true drop-in replacement.
When should I choose SN74HC367N instead of 74HC367N?
Choose the manufacturer-labeled SN74HC367N when procurement, traceability, or exact ordering-option identification matters. The 74HC367N appears in cross-reference material as a functionally comparable generic designation, but supplier branding and ordering codes can differ. The SN74HC367N provides a clearly defined Texas Instruments 16-PDIP ordering option, so engineers can evaluate it against the specific requirement for manufacturer, package, temperature range, and qualification.
SN74HC367N versus MM70C97J/883: which is better for a legacy design?
The SN74HC367N is generally the more straightforward choice for a new or modified design because it is identified directly with the Texas Instruments SN74HC367 family and its 16-PDIP package. The MM70C97J/883 is described in TI engineering discussion as functionally equivalent, but a legacy replacement decision still requires checking temperature grade, supply range, timing, output loading, and package construction. Choose the SN74HC367N when current family documentation and standard commercial sourcing are priorities.
Is SN74HC367N suitable for memory address and clock driving?
Yes, the SN74HC367N is suitable for memory-address and clock-driving functions when its specified electrical limits are respected. The Texas Instruments family description identifies the HC367 for improving drive performance and density in three-state memory-address drivers, clock drivers, and bus-oriented interfaces. Confirm propagation delay, output current, capacitive-load limits, and timing margins in the manufacturer datasheet for the actual board.
What are the key specifications of SN74HC367N that engineers should know?
The principal specifications are a 2 V to 6 V operating range, six non-inverting channels, two independently controlled output banks, three-state outputs, and a 16-PDIP package. The four-driver and two-driver organization comes from the Texas Instruments manufacturer datasheet. The device is a digital logic IC rather than a power component, so SOA data is not applicable and thermal analysis is normally less significant than signal-integrity and timing verification.

엔지니어링 참조 데이터: SN74HC367N — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the SN74HC367N for a new 16-PDIP design that requires six non-inverting 3-state channels organized into independently enabled four-driver and two-driver banks. Its 2 V to 6 V range supports common CMOS systems, while the clearly identified Texas Instruments ordering option simplifies procurement and documentation. Select SN54HC367N or SN54HC367 when the installation requires a military-temperature family option, after checking the detailed electrical limits. Consider MM70C97J/883 when maintaining a legacy National Semiconductor-based design and its qualification records, but verify timing and temperature requirements rather than relying only on functional equivalence. The 74HC367N is a closely related family designation, though the SN74HC367N is preferable when exact manufacturer identity and ordering documentation are priorities. None of these devices changes the SN74HC367's basic truth table, so output-enable sequencing and disabled-net states should be validated on the final PCB.

대체품과의 비교

파라미터 이 제품 SN54HC367N 74HC367N MM70C97J/883 SN54HC367
Package 16-PDIP 16-PDIP 16-PDIP 16-PDIP 16-PDIP
Brand Texas Instruments Texas Instruments Texas Instruments National Semiconductor Texas Instruments
Number of Channels 6 6 6 6 6
Output Bank Organization 4 drivers and 2 drivers 4 drivers and 2 drivers 4 drivers and 2 drivers 4 drivers and 2 drivers 4 drivers and 2 drivers
Output Enable Inputs 2 independent active-low inputs 2 independent active-low inputs 2 independent active-low inputs 2 independent active-low inputs 2 independent active-low inputs
Output State 3-state with high-impedance disable 3-state with high-impedance disable 3-state with high-impedance disable 3-state with high-impedance disable 3-state with high-impedance disable
Logic Polarity Non-inverting Non-inverting Non-inverting Non-inverting Non-inverting

주요 차별점

  • Independently controlled four-driver and two-driver banks (vs 74HC367N)
  • Commercial-temperature ordering option (vs SN54HC367N)
  • Current family documentation for design-in (vs MM70C97J/883)

설계 노트

Route each input directly to its associated output and keep the enable inputs away from high-speed switching nets to minimize coupling into output-enable timing. The DIP footprint provides generous routing flexibility, but input and output traces should still be short enough to limit ringing, crosstalk, and propagation-delay variation. Use a continuous ground plane or equivalent low-impedance return path so the six buffered outputs share an effective reference with the driven logic system.

Do not allow two enabled output channels to drive the same net with opposite logic states. The SN74HC367N uses three-state outputs, but the high-impedance condition does not automatically resolve a conflict between two active drivers. Interlock the two output-enable controls where multiple groups share a bus, and specify the required state of disabled nets so downstream receivers do not float during transitions or reset conditions.

Check the complete signal path against the manufacturer timing and output-current data, including input capacitance, trace capacitance, receiving-device input current, and propagation-delay margins. For longer traces or cable-connected loads, measure edge shape at the far endpoint rather than assuming nominal CMOS edge rates. If ringing causes additional settling time, reduce the load or add a source-series termination resistor selected from impedance and edge-rate analysis.

Place the device so that the supply and ground leads have short, low-impedance paths to the system rails. In a through-hole design, excessive lead length can create additional loop area and make switching-node coupling more likely. Confirm that the chosen socket, board, and assembly process support the 16-PDIP footprint, and inspect the seating plane for solder bridges between adjacent high-speed enable and data pins.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The supplied product listings identify the family and package but do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this general-purpose commercial logic device.

데이터 검증일: 2026-11-18 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

sn74hc367n datasheet SN74HC367N pinout SN74HC367N datasheet pdf SN74HC367N equivalent SN74HC367N replacement SN74HC367N cross reference SN74HC367N vs 74HC367N Texas Instruments SN74HC367N SN74HC367N 16-PDIP SN74HC367N 3-state buffer SN74HC367N memory address driver SN74HC367N clock driver SN74HC367N price SN74HC367N stock What does SN74HC367N do?

관련 부품 & 용어

Texas Instruments SN74HC367N SN74HC367 SN54HC367N SN54HC367 74HC367N MM70C97J/883 National Semiconductor hex buffer line driver logic IC digital semiconductor CMOS logic three-state output high-impedance state non-inverting buffer active-low output enable 16-PDIP DIP package through-hole package 2 V to 6 V supply memory address driver clock driver shared bus output-enable sequencing
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기