SN74HC540N - 8-Channel 3-State Inverting Buffer | TI
MPN: SN74HC540N ✓ AktifSN74HC540N Ringkasan
A three-state buffer, also called a tristate logic buffer or bus driver, is a digital logic component that can actively drive a logic 0, actively drive a logic 1, or present a high-impedance state. The high-impedance state allows multiple devices to share a bus without creating contention. The SN74HC540N combines eight channels and common output-enable control in one package, making it useful where several bidirectional or multiplexed data paths require controlled bus access.
The SN74HC540N provides eight inverting channels, tristate outputs, and bus-driver output capability. Its stated operating supply range is 2 V to 6 V, supporting both 2 V, 3 V, and 5 V logic systems. The manufacturer describes the device as a high-speed Si-gate CMOS logic family and identifies the family as compatible with low-power Schottky TTL. Inputs and outputs are located on opposite package sides, reducing routing congestion around the device.
The three-state control gate is implemented as a 2-input NOR function. Consequently, either output-enable input being asserted forces the corresponding outputs into the high-impedance state, while both controls being deasserted allows normal operation. The inverting channel architecture reverses the logic level at every output. These features make the part suitable for bus isolation, data routing, test-interface multiplexing, and systems that need to avoid output contention during parallel-bus transfers.
Typical uses include computer and peripheral bus interfacing, memory-module address or data buffering, test-equipment input isolation, industrial control interfaces, and compact digital systems that require a higher drive capability than standard CMOS gates. The 20-PDIP package is also convenient for prototyping, educational assemblies, through-hole production, and repair work where a socketed package is preferred.
PCB layout should preserve the separation between the input side and output side of the device. Keep output-enable traces away from high-speed data paths where possible, and terminate any long traces in a manner appropriate to the signal edge rate. Because the logic family operates from 2 V to 6 V, verify every attached device uses compatible supply and input thresholds before replacing an existing TTL or LSTTL buffer.
This page combines manufacturer specifications, device-family information, direct replacement considerations, package details, and practical routing guidance. It also distinguishes verified electrical facts from parameters that must be checked in the manufacturer datasheet, helping engineers select and implement the SN74HC540N without confusing a generic 74HC function with the exact ordering code and package.
Pilihan pengganti yang segera untuk SN74HC540N — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
SN74HCT540N
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
CD74HC540E
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
74HC540N
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
SN74HC540N Penilaian maksimum & Ciri-ciri Elektrik
| Number of Channels | 8 channels |
| Output Polarity | Inverting, 1 inversion per channel |
| Output State | 3-state output, including high-impedance state |
| Supply Voltage Range | 2 V to 6 V |
| Logic Family | HC, high-speed Si-gate CMOS |
| Output Capability | 8 bus-driver channels |
| Kemasan | 20-pin DIP through-hole package |
| Kiraan Pin | 20 pins |
| Output Enable Gate | 2-input NOR gate |
| Pin Arrangement | Inputs and outputs on opposite package sides |
| Logic Compatibility | Compatible with low-power Schottky TTL family |
| Technology | Si-gate CMOS, 1 process family |
| Standard | JEDEC standard no. 7A |
| Jenis Pemasangan | Through-hole, 1 mounting style |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Panduan Konfigurasi Pin SN74HC540N 20-pin dip through-hole package
Konfigurasi pin untuk SN74HC540N (20-pin dip through-hole package pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk SN74HC540N.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
SN74HC540N patut untuk 6 aplikasis: Shared Parallel Data Bus, Computer Peripheral Interfacing, Test and Measurement Signal Isolation, Industrial Control Signal Routing, Memory and Processor Data Buffering, Educational and Legacy Through-Hole Systems.
Shared Parallel Data Bus
The SN74HC540N is suitable for a shared parallel data bus because eight inverting channels can be placed in a high-impedance state when another device owns the bus. The 2-input NOR output-enable arrangement provides a convenient way to disable all eight outputs through common control logic. Keeping inputs and outputs on opposite package sides simplifies routing into and out of the device. The design must guarantee that no two enabled drivers simultaneously drive the same node. Check enable timing against the receiving device's setup and hold requirements, and verify output-drive capability against the actual bus capacitance and trace length.
Disebarkan
Computer Peripheral Interfacing
The SN74HC540N can buffer data lines between a computer bus and a peripheral interface while preserving the octal organization of the original logic design. Its eight inverting channels operate from 2 V to 6 V, allowing use in several legacy CMOS systems, while the tristate outputs permit isolation from the shared bus. The opposite-side input and output arrangement reduces PCB routing congestion. For a reliable interface, calculate the capacitive loading presented by connectors and cables, confirm that the selected logic family has compatible thresholds, and account for propagation delay when the bus timing was designed around the original device.
Disebarkan
Test and Measurement Signal Isolation
The SN74HC540N can isolate groups of test signals from a common measurement bus by placing its eight outputs in the high-impedance state unless the selected group is enabled. This makes it useful in test fixtures, diagnostic interfaces, and legacy automated test equipment where multiple stimulus sources may connect to the same conductors. Its 2 V to 6 V operating range supports multiple logic rails, while the bus-driver output capability is useful for driving fixture wiring. Disable inactive channels before they are connected, observe the device's enable timing, and verify that the load does not exceed the output-drive and capacitive-loading limits in the manufacturer datasheet.
Disebarkan
Industrial Control Signal Routing
The SN74HC540N can serve as a routing stage between industrial control logic and a multiplexed field-bus or peripheral interface. Eight three-state outputs allow the controller to participate in a shared line only during the assigned communication interval, while the inverting channels reproduce the logic convention of the original 74HC design. The 20-pin DIP package is especially useful for legacy industrial controller cards and prototype assemblies. Confirm that the 2 V to 6 V operating range covers the controller rail, review input thresholds for every connected device, and provide adequate rise-time margin for the installed cable or wiring harness.
Disebarkan
Memory and Processor Data Buffering
The SN74HC540N can provide octal tristate buffering between memory, processor, or peripheral logic and a shared internal bus. Placing data inputs and outputs on opposite sides of the package supports straightforward board partitioning, while three-state outputs allow the device to release the bus during another module's access cycle. The HC family supports a 2 V to 6 V range, but the exact edge-rate behavior must be matched to the memory or processor interface. Confirm setup and hold margins, output-drive capability, bus capacitance, and enable timing, especially in designs that originally used a specific manufacturer or logic-threshold family.
Disebarkan
Educational and Legacy Through-Hole Systems
The SN74HC540N is practical for educational breadboards, legacy controller boards, socketed logic experiments, and repair assemblies that benefit from a through-hole package. Eight accessible channels allow students to investigate inversion, bus contention, output enable, and high-impedance behavior in a single 20-pin DIP device. Its 2 V to 6 V supply range provides flexibility for common laboratory rails. Build prototypes with a regulated supply, common ground, and deliberate pull resistors where required by the surrounding bus. Before connecting an older TTL circuit, select HC or HCT threshold behavior according to the source voltage and verify timing at the intended frequency.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk SN74HC540N — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | SN74HCT540N | CD74HC540E | 74HC540N |
|---|---|---|---|---|
| Package | 20-PDIP | 20-PDIP | 20-PDIP | 20-PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels |
| Output Polarity | Inverting | Inverting | Inverting | Inverting |
| Output State | 3-state output | 3-state output | 3-state output | 3-state output |
| Logic Family | HC, high-speed Si-gate CMOS | HCT, high-speed Si-gate CMOS | HC, high-speed Si-gate CMOS | HC, high-speed Si-gate CMOS |
Penyeberangsung Jelas
- Common three-state bus control (vsSN74HCT540N)
- Wide CMOS supply range (vsCD74HC540E)
- Opposite-side signal organization (vs74HC540N)
Catatan Desain
Route the eight data inputs from one side of the SN74HC540N and the eight inverting outputs from the opposite side. This arrangement is a defining feature of the device and helps avoid crossing data paths on the PCB. Place protection or series-resistance components where signal integrity requires them, and keep the two output-enable inputs on a controlled routing path. Confirm that the final footprint matches the 20-pin DIP lead spacing and pin-1 orientation before fabrication.
Never allow two enabled output channels to drive the same bus node simultaneously. The tristate outputs remove contention only when the conflicting driver is placed in its high-impedance state. The 2-input NOR enable arrangement means either asserted enable input can disable the outputs, so verify control polarity in firmware or hardware before assuming an asserted signal enables the bus. Also account for output propagation delay when sequencing bus owners.
Check capacitive loading, trace length, and receiver thresholds rather than treating the SN74HC540N as an unlimited bus driver. Its 2 V to 6 V operation supports several logic rails, but the connected source must remain compatible with the HC input thresholds. At higher bus speeds, use short traces, a suitable topology, and the propagation-delay and output-drive limits from the manufacturer datasheet. A resistor may be appropriate on a lightly loaded control line, but it must not be added in a way that conflicts with the output-enable timing.
Maklumat Kesediaan
The family documentation identifies JEDEC standard no. 7A. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact ordering code are not stated and require confirmation from the manufacturer or authorized supply documentation.