Texas Instruments

SN74HC540N - 8-Channel 3-State Inverting Buffer | TI

부품 번호: SN74HC540N ✓ 활성
2 V to 6 V Vdss 20-pin DIP through-hole package Package
MOQ: 1 |

SN74HC540N 개요

Texas Instruments SN74HC540N is an octal high-speed CMOS buffer and line driver with eight inverting channels, three-state outputs, and a 2 V to 6 V supply range. It is packaged in a 20-pin through-hole DIP and is designed to provide bus-driving capability while placing inputs and outputs on opposite sides of the package for easier printed-circuit-board routing.

A three-state buffer, also called a tristate logic buffer or bus driver, is a digital logic component that can actively drive a logic 0, actively drive a logic 1, or present a high-impedance state. The high-impedance state allows multiple devices to share a bus without creating contention. The SN74HC540N combines eight channels and common output-enable control in one package, making it useful where several bidirectional or multiplexed data paths require controlled bus access.

The SN74HC540N provides eight inverting channels, tristate outputs, and bus-driver output capability. Its stated operating supply range is 2 V to 6 V, supporting both 2 V, 3 V, and 5 V logic systems. The manufacturer describes the device as a high-speed Si-gate CMOS logic family and identifies the family as compatible with low-power Schottky TTL. Inputs and outputs are located on opposite package sides, reducing routing congestion around the device.

The three-state control gate is implemented as a 2-input NOR function. Consequently, either output-enable input being asserted forces the corresponding outputs into the high-impedance state, while both controls being deasserted allows normal operation. The inverting channel architecture reverses the logic level at every output. These features make the part suitable for bus isolation, data routing, test-interface multiplexing, and systems that need to avoid output contention during parallel-bus transfers.

Typical uses include computer and peripheral bus interfacing, memory-module address or data buffering, test-equipment input isolation, industrial control interfaces, and compact digital systems that require a higher drive capability than standard CMOS gates. The 20-PDIP package is also convenient for prototyping, educational assemblies, through-hole production, and repair work where a socketed package is preferred.

PCB layout should preserve the separation between the input side and output side of the device. Keep output-enable traces away from high-speed data paths where possible, and terminate any long traces in a manner appropriate to the signal edge rate. Because the logic family operates from 2 V to 6 V, verify every attached device uses compatible supply and input thresholds before replacing an existing TTL or LSTTL buffer.

This page combines manufacturer specifications, device-family information, direct replacement considerations, package details, and practical routing guidance. It also distinguishes verified electrical facts from parameters that must be checked in the manufacturer datasheet, helping engineers select and implement the SN74HC540N without confusing a generic 74HC function with the exact ordering code and package.

드롭인 대체품: SN74HC540N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

SN74HCT540N

✅ 드롭인
📦 20-PDIP
Same 8-channel, inverting, three-state function and 20-pin package (0 channel difference), but the HCT family uses TTL-compatible input thresholds rather than the HC family thresholds

📋 참조 대체품 (카탈로그에 없음)

CD74HC540E

✅ 드롭인
📦 20-PDIP
Same 8-channel, inverting, three-state function and 20-pin package (0 channel difference); manufacturer-specific timing and drive-current values require comparison

📋 참조 대체품 (카탈로그에 없음)

74HC540N

✅ 드롭인
📦 20-PDIP
Same 8-channel, inverting, three-state function and 20-pin package (0 channel difference); manufacturer-specific propagation-delay and output-drive values require comparison

📋 참조 대체품 (카탈로그에 없음)

SN74HC540N 최대 정격 & 전기적 특성

Number of Channels 8 channels
Output Polarity Inverting, 1 inversion per channel
Output State 3-state output, including high-impedance state
Supply Voltage Range 2 V to 6 V
Logic Family HC, high-speed Si-gate CMOS
Output Capability 8 bus-driver channels
패키지 20-pin DIP through-hole package
핀 수 20 pins
Output Enable Gate 2-input NOR gate
Pin Arrangement Inputs and outputs on opposite package sides
Logic Compatibility Compatible with low-power Schottky TTL family
Technology Si-gate CMOS, 1 process family
Standard JEDEC standard no. 7A
실장 유형 Through-hole, 1 mounting style
RoHS 상태 unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

SN74HC540N 20-pin dip through-hole package 핀 구성 가이드

SN74HC540N(20-pin dip through-hole package 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.

SN74HC540N의 20-pin dip through-hole package 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: SN74HC540N.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

SN74HC540N 적합 용도: 6 애플리케이션s: Shared Parallel Data Bus, Computer Peripheral Interfacing, Test and Measurement Signal Isolation, Industrial Control Signal Routing, Memory and Processor Data Buffering, Educational and Legacy Through-Hole Systems.

🖥️

Shared Parallel Data Bus

The SN74HC540N is suitable for a shared parallel data bus because eight inverting channels can be placed in a high-impedance state when another device owns the bus. The 2-input NOR output-enable arrangement provides a convenient way to disable all eight outputs through common control logic. Keeping inputs and outputs on opposite package sides simplifies routing into and out of the device. The design must guarantee that no two enabled drivers simultaneously drive the same node. Check enable timing against the receiving device's setup and hold requirements, and verify output-drive capability against the actual bus capacitance and trace length.

🖥️

Computer Peripheral Interfacing

The SN74HC540N can buffer data lines between a computer bus and a peripheral interface while preserving the octal organization of the original logic design. Its eight inverting channels operate from 2 V to 6 V, allowing use in several legacy CMOS systems, while the tristate outputs permit isolation from the shared bus. The opposite-side input and output arrangement reduces PCB routing congestion. For a reliable interface, calculate the capacitive loading presented by connectors and cables, confirm that the selected logic family has compatible thresholds, and account for propagation delay when the bus timing was designed around the original device.

🔧

Test and Measurement Signal Isolation

The SN74HC540N can isolate groups of test signals from a common measurement bus by placing its eight outputs in the high-impedance state unless the selected group is enabled. This makes it useful in test fixtures, diagnostic interfaces, and legacy automated test equipment where multiple stimulus sources may connect to the same conductors. Its 2 V to 6 V operating range supports multiple logic rails, while the bus-driver output capability is useful for driving fixture wiring. Disable inactive channels before they are connected, observe the device's enable timing, and verify that the load does not exceed the output-drive and capacitive-loading limits in the manufacturer datasheet.

🏭

Industrial Control Signal Routing

The SN74HC540N can serve as a routing stage between industrial control logic and a multiplexed field-bus or peripheral interface. Eight three-state outputs allow the controller to participate in a shared line only during the assigned communication interval, while the inverting channels reproduce the logic convention of the original 74HC design. The 20-pin DIP package is especially useful for legacy industrial controller cards and prototype assemblies. Confirm that the 2 V to 6 V operating range covers the controller rail, review input thresholds for every connected device, and provide adequate rise-time margin for the installed cable or wiring harness.

🖥️

Memory and Processor Data Buffering

The SN74HC540N can provide octal tristate buffering between memory, processor, or peripheral logic and a shared internal bus. Placing data inputs and outputs on opposite sides of the package supports straightforward board partitioning, while three-state outputs allow the device to release the bus during another module's access cycle. The HC family supports a 2 V to 6 V range, but the exact edge-rate behavior must be matched to the memory or processor interface. Confirm setup and hold margins, output-drive capability, bus capacitance, and enable timing, especially in designs that originally used a specific manufacturer or logic-threshold family.

🧩

Educational and Legacy Through-Hole Systems

The SN74HC540N is practical for educational breadboards, legacy controller boards, socketed logic experiments, and repair assemblies that benefit from a through-hole package. Eight accessible channels allow students to investigate inversion, bus contention, output enable, and high-impedance behavior in a single 20-pin DIP device. Its 2 V to 6 V supply range provides flexibility for common laboratory rails. Build prototypes with a regulated supply, common ground, and deliberate pull resistors where required by the surrounding bus. Before connecting an older TTL circuit, select HC or HCT threshold behavior according to the source voltage and verify timing at the intended frequency.

추천 제품 요약

SN74HC540N Texas Instruments 사용처: Shared Parallel Data Bus, Computer Peripheral Interfacing, Test and Measurement Signal Isolation, Industrial Control Signal Routing, Memory and Processor Data Buffering, Educational and Legacy Through-Hole Systems CD74HC540E Alternate-source tristate buffer 사용처: Shared Parallel Data Bus, Computer Peripheral Interfacing, Industrial Control Signal Routing, Memory and Processor Data Buffering, Educational and Legacy Through-Hole Systems 74HC540N Alternate-source tristate buffer 사용처: Shared Parallel Data Bus, Test and Measurement Signal Isolation, Industrial Control Signal Routing, Educational and Legacy Through-Hole Systems SN74HCT540N TTL-threshold alternative 사용처: Computer Peripheral Interfacing, Test and Measurement Signal Isolation, Memory and Processor Data Buffering
What is the SN74HC540N?
The SN74HC540N is an eight-channel, inverting CMOS buffer and line driver with three-state outputs. According to the Texas Instruments SN74HC540 datasheet, it operates from 2 V to 6 V, provides bus-driver output capability, and places inputs and outputs on opposite sides of a 20-pin DIP package. The high-impedance output state allows the device to share a bus without causing contention when another buffer is active.
What is the operating voltage of SN74HC540N?
The SN74HC540N operates from 2 V to 6 V, according to the Texas Instruments product page and manufacturer datasheet. This range supports common low-voltage CMOS logic systems, including nominal 2 V, 3 V, and 5 V rails. The operating voltage of attached devices must remain compatible with the SN74HC540N input thresholds and output levels, so verify the complete interface before substituting it into an existing board.
What are the key specifications of SN74HC540N that engineers should know?
The SN74HC540N is an eight-channel, inverting, 3-state buffer and line driver operating from 2 V to 6 V. The Texas Instruments datasheet identifies a 20-pin DIP package, bus-driver output capability, a 2-input NOR output-enable gate, and inputs and outputs on opposite package sides. It belongs to the high-speed Si-gate CMOS HC family and is described as compatible with low-power Schottky TTL.
Where to download the SN74HC540N datasheet PDF?
Download the SN74HC540N datasheet PDF from the official Texas Instruments document link on this page. The manufacturer document is titled “SNx4HC540 Octal Buffers and Line Drivers With 3-State Outputs” and describes the device family, electrical characteristics, pinout, and operating recommendations. Use the ordering-information section to confirm that the SN74HC540N suffix corresponds to the required 20-pin DIP package and temperature grade.
Where can I find the SN74HC540N pinout?
The SN74HC540N pinout is shown in the pin-configuration section of the Texas Instruments SN74HC540 manufacturer datasheet. The package contains 20 pins, with the eight data inputs on one side and eight inverting outputs on the other side. Because no complete manufacturer pin table is reproduced on this page, use the datasheet diagram and pin-description table when assigning PCB tracks or socket connections.
Is SN74HC540N the same as CD74HC540E?
The SN74HC540N and CD74HC540E implement the same octal inverting buffer-and-line-driver function with three-state outputs, but they are offered by different manufacturers and must be checked for device-specific electrical and qualification differences. A direct board substitution requires the same 20-pin DIP pinout, compatible 2 V to 6 V operation, compatible enable-control logic, and acceptable output timing and drive specifications. The Texas Instruments and CD74HC540E datasheets should control the final choice.
SN74HC540N vs CD74HC540E - which is better for a legacy 5 V bus?
The SN74HC540N is generally the preferred choice when the design already uses Texas Instruments logic and requires a documented manufacturer datasheet, while the CD74HC540E can serve as an alternate-source candidate. Both provide eight inverting channels with three-state outputs and use a 20-pin DIP arrangement for the compared ordering codes. Final selection depends on matching propagation delay, output-drive current, supply-current behavior, and enable timing to the original device.
What is the difference between SN74HC540N and SN74HCT540N?
The principal difference is the logic family: SN74HC540N is an HC CMOS device, while SN74HCT540N is the HCT counterpart designed around TTL-compatible input thresholds. Both provide eight inverting channels with three-state outputs in the compared through-hole format. Use SN74HCT540N when the driving source has conventional TTL levels, and confirm its exact supply-voltage and timing ratings against the design before making the substitution.
What can replace SN74HC540N?
The CD74HC540E is a practical cross-manufacturer replacement candidate because it implements the same octal inverting tristate-buffer function in a 20-pin DIP package. The 74HC540N and SN74HCT540N are additional family options with different sourcing or logic-threshold characteristics. A drop-in replacement must still be checked for pinout, enable polarity, propagation delay, output drive, supply range, and operating temperature rather than relying only on the 74HC family name.
When should I choose SN74HC540N over CD74HC540E?
Choose SN74HC540N when you want a Texas Instruments-specified octal inverting tristate buffer for a 2 V to 6 V logic design and have already qualified that manufacturer's device. Choose the CD74HC540E when its timing, output-drive, availability, or qualification characteristics better match the target system. Both use a 20-pin DIP configuration, so PCB compatibility is likely, but electrical equivalence must be established from each manufacturer's datasheet.
Where to buy SN74HC540N online and what is its lead time?
Use the Request a Quote form on this page to request SN74HC540N availability, current lead time, minimum order quantity, and a formal quotation. The request identifies the exact SN74HC540N ordering code, reducing ambiguity between the 20-PDIP package and other package or suffix variants. Manufacturing schedule and stock can vary by lot, so confirm the required quantity and delivery target with a written quotation before committing the order.
What is the price of SN74HC540N?
The current SN74HC540N quotation is obtained through the Request a Quote form on this page. Submit the required quantity, target package, and shipment location so the order can be evaluated against the exact manufacturer part number. This avoids relying on a generic 74HC price that could refer to a different package, logic threshold, temperature grade, or manufacturer.
Is SN74HC540N in stock?
Current SN74HC540N stock status should be confirmed through the Request a Quote form on this page. A distributor search result showing availability is not a guaranteed warehouse allocation for a later order, particularly for standard logic ICs subject to supply-chain changes. Include your required quantity, date code preference, and acceptable delivery schedule with the request for a manufacturing-aware response.
Is SN74HC540N suitable for high-impedance bus interfaces?
Yes, the SN74HC540N is suitable for controlled high-impedance bus interfaces because all eight channels provide three-state outputs. The Texas Instruments datasheet describes a 2-input NOR output-enable arrangement, allowing bus drivers to be disabled when another device must control the shared line. Ensure that only one enabled driver is connected to a node at a time and that all enable signals meet the device's input timing requirements.
What design constraints matter when using SN74HC540N in a 5 V system?
The principal design constraints are logic-level compatibility, enable timing, output contention, and board layout. The SN74HC540N operates within a 2 V to 6 V range, but every connected source and receiver must share compatible thresholds. Place the device according to the opposite-side input/output arrangement, keep enable routing away from critical data nets when practical, and check drive strength and propagation delay against the bus loading before finalizing the layout.

엔지니어링 참조 데이터: SN74HC540N — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose SN74HC540N when the PCB requires an eight-channel inverting tristate buffer in a 20-pin DIP and the system operates from the HC family's 2 V to 6 V range. Choose SN74HCT540N when the driving source uses conventional TTL levels and TTL-compatible input thresholds are more important than native HC thresholds. Consider CD74HC540E as a Texas Instruments alternate-source candidate when its timing, drive, and qualification characteristics match the target application, and consider the NXP 74HC540N when its device-specific electrical data better fits the design. All three candidates preserve the core eight-channel, inverting, three-state function and 20-pin package arrangement. Before replacing the original device, verify pin numbering, enable polarity, propagation delay, output-drive current, supply-current behavior, operating temperature, and the availability of suitable decoupling and bus termination.

대체품과의 비교

파라미터 이 제품 SN74HCT540N CD74HC540E 74HC540N
Package 20-PDIP 20-PDIP 20-PDIP 20-PDIP
Brand Texas Instruments Texas Instruments Texas Instruments NXP Semiconductors
Number of Channels 8 channels 8 channels 8 channels 8 channels
Output Polarity Inverting Inverting Inverting Inverting
Output State 3-state output 3-state output 3-state output 3-state output
Logic Family HC, high-speed Si-gate CMOS HCT, high-speed Si-gate CMOS HC, high-speed Si-gate CMOS HC, high-speed Si-gate CMOS

주요 차별점

  • Common three-state bus control (vs SN74HCT540N)
  • Wide CMOS supply range (vs CD74HC540E)
  • Opposite-side signal organization (vs 74HC540N)

설계 노트

Route the eight data inputs from one side of the SN74HC540N and the eight inverting outputs from the opposite side. This arrangement is a defining feature of the device and helps avoid crossing data paths on the PCB. Place protection or series-resistance components where signal integrity requires them, and keep the two output-enable inputs on a controlled routing path. Confirm that the final footprint matches the 20-pin DIP lead spacing and pin-1 orientation before fabrication.

Never allow two enabled output channels to drive the same bus node simultaneously. The tristate outputs remove contention only when the conflicting driver is placed in its high-impedance state. The 2-input NOR enable arrangement means either asserted enable input can disable the outputs, so verify control polarity in firmware or hardware before assuming an asserted signal enables the bus. Also account for output propagation delay when sequencing bus owners.

Check capacitive loading, trace length, and receiver thresholds rather than treating the SN74HC540N as an unlimited bus driver. Its 2 V to 6 V operation supports several logic rails, but the connected source must remain compatible with the HC input thresholds. At higher bus speeds, use short traces, a suitable topology, and the propagation-delay and output-drive limits from the manufacturer datasheet. A resistor may be appropriate on a lightly loaded control line, but it must not be added in a way that conflicts with the output-enable timing.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The family documentation identifies JEDEC standard no. 7A. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact ordering code are not stated and require confirmation from the manufacturer or authorized supply documentation.

데이터 검증일: 2026-11-18 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

sn74hc540n datasheet sn74hc540n pinout sn74hc540n datasheet pdf sn74hc540n equivalent sn74hc540n replacement sn74hc540n vs cd74hc540e sn74hc540n vs sn74hct540n sn74hc540n 20-dip pinout sn74hc540n tristate buffer application sn74hc540n price sn74hc540n stock texas instruments sn74hc540n

관련 부품 & 용어

Texas Instruments SN74HC540N SN74HCT540N CD74HC540E 74HC540N octal buffer line driver three-state logic tristate output high-impedance state inverting logic CMOS logic Si-gate CMOS HC logic family HCT logic family TTL-compatible input thresholds JEDEC standard no. 7A 20-PDIP package DIP package family through-hole package bus driver 2-input NOR gate output enable parallel data bus industrial control
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기