SN75119D - Differential Line Transceiver | Texas Instruments
MPN: SN75119D ✓ AktifSN75119D Ringkasan
A differential line transceiver is an interface IC that combines a transmitter and receiver for communication over a balanced pair of conductors. It belongs to the broader transceiver and interface-controller hierarchy, where differential signaling improves noise immunity by rejecting common-mode voltage disturbances. The SN75119D supports this function by combining differential line operation with a three-state driver output that can be disabled when multiple devices share a bus.
Key features include operation from a single 5 V supply, three-state driver output circuitry, TTL-compatible driver inputs, and a TTL-compatible receiver output. The enable function allows the receiver to participate in shared-bus communication systems where bus contention must be controlled. These characteristics make the device suitable for legacy industrial data buses, point-to-point balanced links, and systems that require controlled driver states rather than always-active outputs.
The architecture supports both transmitting and receiving on a differential line. The driver accepts TTL-level control signals and places complementary signals onto the bus, while the receiver reconstructs a logic output from the differential pair. Three-state operation provides a high-impedance state when the driver is disabled, allowing multiple transmitters to share the same pair of wires under controlled address or arbitration schemes. The related SN75118 family member uses an enable arrangement as well, while SN75116 and SN75117 devices provide receiver output strobe control.
Typical applications include party-line industrial control buses, data acquisition networks, peripheral-interface equipment, test systems, and legacy communications equipment. The part is also appropriate where a controller must switch a differential transmitter on and off while several nodes remain connected to the same bus. System designers should coordinate enable timing to avoid unwanted driver overlap and preserve signal integrity.
For PCB implementation, place the transceiver close to the connector or bus transceiver to minimize exposed stub length and reduce susceptibility to reflected signals. Follow the manufacturer's pin-description table and recommended decoupling arrangement when assigning tracks. The single 5 V rail should be filtered locally, and unused digital inputs should be held at defined logic levels rather than left floating.
This page organizes the confirmed operating characteristics, package information, sourcing paths, functional-use guidance, and design considerations into a practical engineering reference. It also distinguishes the SN75119 enable architecture from the receiver-strobe behavior of related family members and highlights the design decisions that matter when deploying the SN75119D on a shared differential bus.
Pilihan pengganti yang segera untuk SN75119D — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera SN75119D (sama faktor bentuk dan kaki) — berbeza dalam Product Type, Operating Temperature Range, Package.
SN75118D
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
SN75117D
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →SN75116D
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →SN75119D Spesifikasi
| Product Type | Single-channel differential line transceiver |
| Tegangan Pemberi Arus | 5 V |
| Driver Output State | 3-state |
| Driver Input Compatibility | TTL-compatible |
| Receiver Output Compatibility | TTL-compatible |
| Line Signaling | Differential |
| Control Function | Enable |
| Bilangan Pin | 8 pins |
| Kemasan | 8-SOIC |
| Jenis Pemasangan | Surface mount |
| Gambaran Suhu Operasi | 0 °C to 70 °C |
Panduan Konfigurasi Pin SN75119D 8-soic
Konfigurasi pin untuk SN75119D (8-soic pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk SN75119D.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
SN75119D patut untuk 6 aplikasis: Party-Line Industrial Data Bus, Legacy Data Acquisition Equipment, Peripheral Communication Interface, Balanced Point-to-Point Link, Process-Control Communication, Test and Diagnostic Systems.
Party-Line Industrial Data Bus
The SN75119D fits a shared party-line data bus because it combines a differential driver with a three-state output and an enable control function. The bus controller can disable a transmitter so it presents a high-impedance state while another node communicates over the same conductor pair. Operating from a single 5 V rail also simplifies the interface between industrial equipment and TTL-compatible logic. Design the enable sequence so only one active driver drives the line at a time, and place the IC close to the bus connector to minimize stub length, reflections, and susceptibility to externally coupled noise.
Disebarkan
Legacy Data Acquisition Equipment
The SN75119D can connect older balanced measurement and control equipment to modern digital logic while preserving the distinctive characteristics of a differential line interface. Its driver accepts TTL-compatible control signals, and its receiver produces a TTL-compatible output, allowing the recovered bus state to feed counters, processors, or recording equipment. Differential line operation helps reject common-mode disturbances encountered near industrial machinery. Keep power and return paths appropriately referenced, place the transceiver near the cable entry, and verify that the bus timing and termination arrangement remain compatible with the connected equipment.
Disebarkan
Peripheral Communication Interface
The SN75119D is appropriate for legacy peripheral links that use a balanced pair rather than a single-ended signal. The transmitter places complementary signals onto the line, while the receiver reconstructs a logic level for the host interface. Because the driver supports a three-state condition, the same board can accommodate bus sharing, test isolation, or controlled connection to another peripheral. Confirm the enable polarity and sequencing in the manufacturer documentation, use a clean 5 V supply, and avoid routing the differential pair alongside high-energy switching nodes.
Disebarkan
Balanced Point-to-Point Link
For a point-to-point balanced connection, the SN75119D provides the transmitter and receiver functions needed to communicate over a differential pair. TTL-compatible driver inputs allow ordinary digital control signals to operate the bus, while the TTL-compatible receiver output can connect directly to suitable digital logic. The differential signaling arrangement can improve common-mode noise rejection compared with a single-ended connection. Maintain a controlled return arrangement, follow the recommended power decoupling, and keep the route from the IC to the connector short to preserve signal quality and minimize reflected behavior.
Disebarkan
Process-Control Communication
The SN75119D can support older process-control equipment that distributes commands and measurements over a shared differential bus. Its enable control permits the system to isolate a transmitting node while keeping the receiver available for monitoring bus activity. The single 5 V supply requirement simplifies integration with logic-level control systems, and the three-state driver avoids active contention when multiple nodes are connected. In installations with motors, relays, or long cable runs, place the transceiver near the line interface, use appropriate protection at the connector, and coordinate enable timing to avoid simultaneous drive states.
Disebarkan
Test and Diagnostic Systems
The SN75119D can serve as the bus interface in test and diagnostic systems that need to interrogate a balanced line while sharing the conductor pair with other equipment. Its receiver reports the recovered bus state to test logic, while the three-state driver allows the system to remain passive during portions of the test sequence. This makes bus-node selection and fault isolation more practical. Use controlled enable signals in the test controller, avoid contention during transition periods, and verify receiver timing against the equipment under test before automating repetitive measurements.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk SN75119D — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini |
|---|---|
| Brand | Texas Instruments |
| Package | 8-SOIC |
| Product Type | Differential line transceiver |
| Number of Pins | 8 pins |
| Supply Voltage | Single 5 V supply |
| Driver Output | 3-state |
| Driver Input | TTL-compatible |
| Receiver Output | TTL-compatible |
| Line Mode | Differential |
| Control Function | Enable |
| Primary Application | Party-line and data-bus communication |
| Operating Temperature Range | 0 °C to 70 °C |
Penyeberangsung Jelas
- Enable-based control distinguishes the SN75119 from receiver-strobe family members (vsSN75116)
- Three-state driver supports shared differential conductors (vsSN75117)
- Single 5 V operation simplifies digital-interface integration (vsSN75118)
Catatan Desain
Coordinate driver-enable timing so that no two connected nodes actively drive the differential pair simultaneously. The three-state output permits bus sharing, but incorrect sequencing can still create contention, excess current, and distorted communication. Use the manufacturer's control timing and receiver output behavior when defining the transition sequence, and include a fail-safe disable state during reset or fault conditions.
Place the SN75119D close to the external line connector and route the differential conductors as a compact pair. Minimize stubs and avoid discontinuities between the transceiver pins and connector. Provide local supply decoupling at the device and maintain a low-impedance return path beneath or near the signal route. These layout practices reduce reflections and improve noise immunity on the balanced bus.
Confirm the bus termination and cable arrangement with the manufacturer recommendations and the connected equipment specifications. The receiver's frequency-response characteristics can affect noise immunity and usable signaling rate, so do not infer performance from the 5 V supply rating alone. Validate timing and common-mode limits in the final cable, connector, grounding, and termination environment before treating the interface as production-ready.
Maklumat Kesediaan
The manufacturer product page identifies the SN75119 family and its 8-pin PDIP configuration, while the SN75119D distributor entry identifies an 8-SOIC package. Explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not present in the available product information.