TLV2401CD - 16V, 5.5kHz MicroPower RRIO Op Amp | TI
MPN: TLV2401CD ✓ AktifTLV2401CD Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2401 belongs to the rail-to-rail-input/output operational-amplifier family, where the input common-mode range and output swing extend toward the supply rails. This category combines signal amplification, impedance buffering, filtering, and closed-loop control functions within a general-purpose analog IC.
The most important feature of the TLV2401 is its low supply current. Texas Instruments describes the TLV2401 family as drawing approximately 880 nA per channel, making it suitable for battery-powered equipment where amplifier standby power materially affects operating time. The 5.5 kHz gain-bandwidth product supports low-frequency signal paths rather than high-speed communications, audio-frequency wideband amplification, or fast data acquisition.
Rail-to-rail inputs are valuable when sensor outputs can approach either supply rail. Rail-to-rail output operation similarly improves usable output swing in single-supply systems, although the datasheet's output-voltage limits must still be respected when driving loads. Reverse-battery protection is included in the family description, helping guard the amplifier against excessive input current caused by improper battery installation.
Typical uses include battery-powered sensing, portable instrumentation, low-frequency active filters, sensor conditioning, threshold detection, and embedded control loops. The 16 V maximum supply rating supports higher-voltage industrial systems, while the 8-pin SOIC package allows conventional surface-mount assembly and straightforward hand-soldering during prototyping.
The primary design trade-off is bandwidth versus power and flexibility. The 5.5 kHz gain-bandwidth product is adequate for slow sensor signals but can create excessive closed-loop gain error or phase margin concerns at higher frequencies. Designers should select feedback values and source impedances that preserve stability, while verifying input and output ranges at the actual supply voltage.
This product overview combines the manufacturer’s device identity and ordering information with package details, application guidance, drop-in replacement analysis, and practical considerations for implementing a low-power rail-to-rail analog signal chain.
Pilihan pengganti yang segera untuk TLV2401CD — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
TLV2401IDG4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TLV2401CD Penilaian maksimum & Ciri-ciri Elektrik
| Number of Channels | 1 channel |
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 16 V |
| Gain-Bandwidth Product | 5.5 kHz |
| Supply Current per Channel | 880 nA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Reverse-Battery Protection | Supported |
| Gambaran Suhu Operasi | 0 °C to 70 °C |
| Kemasan | 8-pin SOIC (D) |
| Jenis Pemasangan | Surface mount |
| Jenis Output | Rail-to-rail |
Konfigurasi Pin TLV2401CD
| Pin 1 | OUT — Operational-amplifier output |
| Pin 2 | IN- — Inverting input |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | V- — Negative supply or ground connection |
| Pin 5 | NC — Not connected |
| Pin 6 | NC — Not connected |
| Pin 7 | V+ — Positive supply input |
| Pin 8 | OUT — Operational-amplifier output |
Aplikasi Biasa
TLV2401CD patut untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Portable Instrumentation, Industrial Limit Detection, Low-Frequency Active Filtering, RS-485 Interface Signal Conditioning, Precision Current Monitoring.
Battery-Powered Sensor Conditioning
The TLV2401CD suits low-energy sensor interfaces because its approximately 880 nA supply current limits amplifier overhead when the battery source is only a few volts. Rail-to-rail inputs allow signals from resistive dividers, photocells, or slow analog sensors to use much of the available supply range without immediate input saturation. Configure the amplifier as a non-inverting or inverting stage with feedback values that keep closed-loop gain appropriate for the 5.5 kHz gain-bandwidth product. A capacitive load at the sensor or ADC input may require a series isolation resistor to prevent instability.
Disebarkan
Portable Instrumentation
The TLV2401CD is appropriate for portable measurement equipment where each analog channel must consume very little power while handling slow sensor or transducer signals. Its single-channel 8-pin SOIC package simplifies routing, while rail-to-rail input and output behavior improves signal utilization in single-supply systems. The 5.5 kHz gain-bandwidth product is well matched to temperature, pressure, and position measurements that do not require wideband amplification. Designers should still account for input offset, bias current, noise, and output-load limits from the manufacturer datasheet when setting the minimum resolvable signal.
Disebarkan
Industrial Limit Detection
A TLV2401CD threshold detector can compare a slowly changing process signal with a reference and generate a clean logic-level transition for downstream monitoring. Rail-to-rail inputs help accommodate signals spanning much of the single-supply range, and the approximately 880 nA operating current supports distributed, low-power monitoring nodes. The 5.5 kHz bandwidth provides margin for slow process dynamics without consuming the power of a high-speed amplifier. Verify input-referred offset and output logic-level compatibility at the selected supply voltage, especially near the decision threshold.
Disebarkan
Low-Frequency Active Filtering
The TLV2401CD can implement low-frequency active filters in sensor and audio-control paths where the target signal bandwidth is well below 5.5 kHz. Rail-to-rail output operation provides useful swing in a single-supply design, and the low approximately 880 nA supply current benefits continuously powered monitoring equipment. Component tolerances and the amplifier's finite gain-bandwidth product affect filter cutoff and phase, so simulation should include realistic source and load impedities. Keep the connected load within the manufacturer-specified operating range and assess stability when driving sampling inputs.
Disebarkan
RS-485 Interface Signal Conditioning
TLV2401CD can amplify or filter the slow, low-level signal presented to a communication interface without introducing a high quiescent-power burden. Its approximately 880 nA supply current is useful in distributed acquisition systems, and the 5.5 kHz bandwidth is appropriate for low-rate supervisory or control signals rather than high-speed data. A separate transceiver handles the physical RS-485 layer, so the amplifier should condition only the analog signal presented to its input. Confirm logic thresholds, supply levels, and isolation requirements before combining the analog and communication sections.
Disebarkan
Precision Current Monitoring
The TLV2401CD can condition a scaled voltage derived from a shunt or current-sensing amplifier when the required bandwidth is low. Rail-to-rail input behavior helps preserve small signals in compact single-supply systems, while the 880 nA per-channel current supports power-constrained monitoring. The 5.5 kHz gain-bandwidth product is suitable for slow current trends and protection thresholds but not for high-bandwidth motor-current waveforms. Select external resistor values for the required current range, verify amplifier input limits, and ensure the upstream current-sense device operates within its own common-mode range.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TLV2401CD — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TLV2401IDG4 |
|---|---|---|
| Package | SOIC-8 (D) | SOIC-8 (D) |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 1 channel | 1 channel |
| Maximum Supply Voltage | 16 V | 16 V |
| Gain-Bandwidth Product | 5.5 kHz | 5.5 kHz |
| Supply Current per Channel | 880 nA | 880 nA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Operating Temperature Range | 0 °C to 70 °C | Industrial-temperature grade |
| Reverse-Battery Protection | Supported | Supported |
Penyeberangsung Jelas
- Lower operating temperature range than the industrial-grade family option (vsTLV2401IDG4)
- Same core family performance in the same 8-pin SOIC footprint (vsTLV2401IDG4)
- Commercial-temperature choice for cost-conscious room-temperature designs (vsTLV2401IDG4)
Catatan Desain
Estimated: using a 3.3 V supply and the manufacturer-described 880 nA channel current, the amplifier's unloaded supply consumption is approximately 2.9 µW. Actual current rises with output load and external bias paths. In battery designs, include the sensor, regulator quiescent current, pull resistors, and any load in the complete power budget rather than treating the amplifier value as the entire system consumption.
Keep the 5.5 kHz gain-bandwidth product in perspective when selecting feedback resistors. Higher closed-loop gain reduces available bandwidth and can alter phase margin, particularly with source capacitance. Place the amplifier close to the source, use short feedback paths, and add a small series isolation resistor when driving an ADC or capacitive sensor input. Validate stability in simulation using the actual source and load models.
Place input and output components close to their corresponding pins to minimize sensitive-node area and trace capacitance. Provide a low-impedance ground reference, route supply current away from high-impedance inputs, and decouple the supply according to the manufacturer application guidance. The SOIC package permits straightforward rework, but thermal performance and input bias current can still affect precision measurements near the thermal limits.
Do not assume that rail-to-rail input and output labels mean every signal can reach either rail exactly. Consult the manufacturer output-swing and input common-mode limits at the actual supply voltage, and account for input offset when making threshold decisions. Avoid using the 880 nA supply-current figure as a load-current capability because output drive and input bias currents are separate specifications.
Maklumat Kesediaan
The device is a general-purpose commercial-temperature operational amplifier rather than an automotive-qualified AEC-Q100 product. Specific environmental and material compliance statuses require confirmation from the manufacturer product documentation.