TLV2461CP - 6.4MHz RRIO Op Amp | Texas Instruments
MPN: TLV2461CP ✓ AktifTLV2461CP Ringkasan
An operational amplifier is an active analog circuit block that amplifies the voltage difference between its inverting and non-inverting inputs. Rail-to-rail input operation allows signals to approach the supply rails, while rail-to-rail output operation gives designers additional output swing near the limits of the available supply voltage. In the broader device hierarchy, the TLV2461CP belongs to the operational-amplifier and analog-signal-chain categories rather than the digital IC or power-management categories.
The TLV2461 family is identified by Texas Instruments as a family of low-power, rail-to-rail input/output operational amplifiers with shutdown capability. The TLV2461CP provides one amplifier circuit in a through-hole PDIP package, which supports prototyping, educational platforms, and industrial assemblies where leaded components are preferred. Its stated 6.4 MHz bandwidth provides substantially more signal-path flexibility than low-frequency general-purpose amplifiers.
A 6 V maximum supply rating supports operation from low-voltage portable systems, while the single-amplifier configuration avoids unused circuitry in applications needing one signal channel. Rail-to-rail inputs are useful when sensing small signals near a lower supply rail, and rail-to-rail outputs help preserve dynamic range when driving a subsequent analog stage. The 8-pin PDIP format also simplifies socket-based construction and hand-soldered prototype assembly compared with a fine-pitch surface-mount package.
Typical uses include low-voltage sensor interfaces, portable measurement equipment, audio and communication signal conditioning, buffer stages, and active filtering. In a portable sensor circuit, the amplifier can sit close to the sensor and process a weak bipolar or unipolar signal before further conditioning. In an active-filter design, its 6.4 MHz bandwidth provides the transition-frequency and phase-margin margin needed for moderate-bandwidth filtering stages.
Design should account for common-mode range, output swing, input bias current, noise, stability, and load capability under the actual supply voltage. Decoupling capacitors should be placed close to the supply pins, and signal routing should minimize parasitic capacitance. Because the TLV2461CP is a leaded PDIP device, board designers should also preserve adequate hole spacing and verify the orientation mark before soldering.
This product page combines the manufacturer identity, ordering package, primary electrical headline, lifecycle context, sourcing guidance, and practical design considerations. It also distinguishes genuine same-package alternatives from parts that merely perform a similar function, helping engineers evaluate replacement decisions without assuming that package compatibility alone guarantees equivalent performance.
Pilihan pengganti yang segera untuk TLV2461CP — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera TLV2461CP (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Input Common-Mode Range, Output Swing.
TLV2461IP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →TLV2461AIP
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
TLV2461CPD
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif rujukan (tidak dalam katalog)
TLV2461CP Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Single-circuit general-purpose operational amplifier |
| Number of Channels | 1 channel |
| Supply Voltage Maximum | 6 V |
| Gain-Bandwidth Product | 6.4 MHz |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Power Class | Low-power operational amplifier |
| Shutdown Function | Available in the TLV246x family |
| Package Type | 8-pin PDIP |
| Kiraan Pin | 8 pins |
| Jenis Pemasangan | Through-hole |
| Status RoHS | Compliant |
Panduan Konfigurasi Pin TLV2461CP 8-pin pdip
Konfigurasi pin untuk TLV2461CP (8-pin pdip pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk TLV2461CP.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TLV2461CP patut untuk 6 aplikasis: Portable Sensor Signal Conditioning, Portable Measurement Instrumentation, Audio Signal Conditioning, Communication Interface Conditioning, Active Filter and Equalization, Industrial Control Analog Front End.
Portable Sensor Signal Conditioning
The TLV2461CP fits low-voltage sensor interfaces because its rail-to-rail inputs can process signals near the supply limits and its 6.4 MHz gain-bandwidth product provides more bandwidth than typical low-frequency general-purpose amplifiers. It can amplify a weak sensor output close to the analog front end before conversion or filtering. The principal checks are sensor source impedance, input bias current, noise behavior, and the input common-mode range at the selected supply voltage.
Disebarkan
Portable Measurement Instrumentation
The TLV2461CP is appropriate for compact instrumentation in which a 6 V supply, a single amplifier channel, and a through-hole package simplify construction. Its 6.4 MHz bandwidth supports moderate-frequency measurement and buffer stages, while rail-to-rail input and output operation improves utilization of a low supply voltage. The PDIP format is particularly useful for socketed prototypes, educational equipment, and assemblies that favor easy inspection or manual rework.
Disebarkan
Audio Signal Conditioning
The TLV2461CP can serve as a low-voltage gain or buffer stage in portable audio signal paths. Its 6.4 MHz gain-bandwidth product covers a substantially wider range than audio-band amplifiers and allows the same device to handle moderate ancillary signals in a mixed analog system. Rail-to-rail output capability can improve available swing, although output-current limits, capacitive-load stability, distortion, and noise must be checked before driving a particular audio load.
Disebarkan
Communication Interface Conditioning
The TLV2461CP is suitable for low-voltage communication circuitry when a signal must be buffered or amplified before entering an analog or digital interface. Its 6.4 MHz bandwidth supports moderate data rates, and rail-to-rail operation is helpful in systems whose signal levels occupy much of the available 6 V supply range. PCB placement should minimize trace length around the amplifier, preserve a continuous ground return, and provide local supply bypassing to avoid adding noise to the communication channel.
Disebarkan
Active Filter and Equalization
The TLV2461CP can implement moderate-bandwidth active filters or equalization stages because its 6.4 MHz gain-bandwidth product provides useful closed-loop bandwidth beyond the audio range. The unity-gain bandwidth is a design resource, not a guaranteed usable filter corner frequency; actual response depends on noise gain, phase margin, load, and tolerances. Prototype on a grounded board and verify stability, gain peaking, and output swing across the intended frequency range.
Disebarkan
Industrial Control Analog Front End
The TLV2461CP can condition low-level analog signals in industrial control boards that require a low-voltage, general-purpose amplifier with a leaded package. Its single-channel configuration avoids allocating multiple amplifier sections, while the 6.4 MHz bandwidth supports faster feedback loops than slow precision-only amplifiers. Industrial deployment should confirm the selected temperature grade, noise and offset requirements, isolation boundaries, grounding strategy, and reliability targets for the finished system.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TLV2461CP — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TLV2461IP | TLV2461AIP | TLV2461CPD |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Amplifier Channels | 1 channel | 1 channel | 1 channel | 1 channel |
| Maximum Supply Voltage | 6 V | 6 V | 6 V | 6 V |
| Gain-Bandwidth Product | 6.4 MHz | 6.4 MHz | 10 MHz | 6.4 MHz |
| Input Common-Mode Range | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input | Rail-to-rail input |
| Output Swing | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
Penyeberangsung Jelas
- Combines 6.4 MHz bandwidth with rail-to-rail input and output operation (vsTLV2461IP)
- Supports a wider operating temperature range than the industrial-grade alternative (vsTLV2461IP)
- Provides additional closed-loop bandwidth margin over the original device (vsTLV2461AIP)
Catatan Desain
Place the input, output, and supply compensation components close to their associated TLV2461CP pins. Keep the ground return short and use a common ground plane for analog routing where practical. Because this is an 8-pin PDIP device, preserve the manufacturer's hole pattern and orient pin 1 from the package notch. Avoid long exposed input traces next to digital return currents to reduce coupled noise.
Decouple each supply connection with local ceramic capacitance and add bulk capacitance where the power source has appreciable impedance. Keep the operating voltage below the 6 V maximum rating, and verify the derating margin at the highest temperature. Rail-to-rail operation improves signal range, but it does not remove the need to check output swing, load current, and input common-mode limits at the actual supply voltage.
Do not treat the 6.4 MHz gain-bandwidth figure as the final closed-loop bandwidth for every circuit. Noise gain, capacitive loading, operating gain, and loop stability determine the usable response. Before replacing TLV2461CP with TLV2461AIP, recalculate filter poles and check phase margin because the alternative has a different bandwidth grade. Also verify pin functions and the exact PDIP footprint rather than relying only on the generic operational-amplifier symbol.
For small-sensor interfaces, minimize the distance from the sensor to the TLV2461CP input and use guarding or a driven guard where leakage from PCB contamination matters. Bias-current error is governed by sensor source impedance, so verify the complete source impedance rather than only the nominal sensor resistance. Add output isolation or filtering if the next stage presents significant capacitance or a nonlinear load.
Maklumat Kesediaan
RoHS compliance is associated with the product listing; no separate REACH, halogen-free, conflict-minerals, or automotive qualification statement was established.