Texas Instruments

TLV2471CD - 2.8MHz RRIO Op Amp | Texas Instruments

MPN: TLV2471CD ✓ Aktif
Up to 6 V Vdss 600 uA per channel Id 8-pin SOIC (D) Package
MOQ: 1 |

TLV2471CD Ringkasan

Texas Instruments TLV2471CD is a single, 6 V, 2.8 MHz rail-to-rail input and output operational amplifier packaged in an 8-pin SOIC. It combines 600 uA per channel supply consumption with a 2.8 MHz gain-bandwidth product, positioning it between low-power and higher-speed CMOS amplifier families.

An operational amplifier is a voltage-gain building block used for signal conditioning, feedback control, buffering, and analog computation. The TLV2471 belongs to the CMOS operational-amplifier hierarchy, where rail-to-rail input and output operation supports signals close to the supply rails. This makes it useful in portable instrumentation, sensor interfaces, battery-powered monitoring, communications, and industrial control systems.

The principal operating characteristics include single-supply operation up to 6 V, 2.8 MHz gain-bandwidth product, and approximately 600 uA supply current per channel. Rail-to-rail input and output capability increases usable signal range in low-voltage systems. The single-amplifier configuration also keeps the SOIC-8 package appropriate where one amplifier per package offers a practical balance between functionality and board area.

The TLV247x family uses CMOS technology to combine low bias consumption with useful AC performance. Its 2.8 MHz bandwidth supports moderate-frequency signal paths and closed-loop applications requiring more bandwidth than a micropower amplifier, while the 600 uA supply requirement preserves low-power system budgets. Exact offset, input-bias-current, noise, output-current, and overload-recovery figures should be taken from the manufacturer datasheet for the selected operating conditions.

Typical uses include low-side current sensing, portable sensor conditioning, buffered ADC inputs, audio and communication signal paths, and feedback control loops. In a current-sense amplifier, the 2.8 MHz bandwidth helps preserve the useful bandwidth of the measured signal. In a portable sensor interface, low supply consumption reduces the load on the battery while rail-to-rail operation accommodates a broad input range.

Design the decoupling network with short traces and place the supply capacitor close to the device. Check output-current limits, input common-mode range, output swing, stability, and noise requirements at the intended supply voltage and load before finalizing the bias point. The manufacturer pin description and package drawing should be used when assigning PCB tracks and selecting bypass-capacitor placement.

This page combines the manufacturer device description, package and ordering information, commercial guidance, and practical engineering guidance for the TLV2471CD. It also identifies same-family drop-in options and highlights the parameters that must be checked before replacing an amplifier in an existing SOIC-8 design.

Pilihan pengganti yang segera untuk TLV2471CD — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera TLV2471CD (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Package, Operating Temperature Range, Technology.

Texas Instruments
Amplifier Type: Single-channel general-purpose operational amplifier
Package: 8-pin PDIP
Technology: LiNCMOS
Bandingkan Dengan TLV2471CD →
Texas Instruments
Operating Temperature Range: -40 °C to +125 °C
Technology: CMOS
Bandingkan Dengan TLV2471CD →

TLV2471AIDR

✅ Masuk Drop-In
📦 8-pin SOIC (D)
Automotive-qualified ordering option with 0% change to the stated 6 V supply, 2.8 MHz bandwidth, and 600 uA per channel

📋 Alternatif rujukan (tidak dalam katalog)

TLV2471ID

✅ Masuk Drop-In
Texas Instruments
📦 8-pin SOIC (D)
Single operational amplifier · 1 circuit · 6 V · 2.8 MHz · 600 µA · Rail-to-rail · Rail-to-rail · CMOS

Hubungi untuk harga

Lihat Datasheet →

TLV2471AID

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin SOIC (D)
Automotive-qualified family option with 0% change to the stated 6 V supply, 2.8 MHz bandwidth, and 600 uA per channel

📋 Alternatif rujukan (tidak dalam katalog)

TLV2471IP

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
📦 8-pin SOIC (D)
Industrial-temperature family option with 0% change to the stated 6 V supply, 2.8 MHz bandwidth, and 600 uA per channel

📋 Alternatif rujukan (tidak dalam katalog)

TLV2471CP

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 8-pin SOIC (D)
Single-channel general-purpose operational amplifier · 1 channel · 6 V · 2.8 MHz · Yes · Yes · 78 dB · 15 nV/√Hz

Hubungi untuk harga

Lihat Datasheet →

TLV2471CD Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type Single operational amplifier
Tegangan Pemberi Arus Up to 6 V
Gain-Bandwidth Product 2.8 MHz
Arus Pemberi Arus 600 uA per channel
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Process Technology CMOS
Number of Channels 1 channel
Kemasan 8-pin SOIC (D)
Jenis Pemasangan Surface mount
Gambaran Suhu Operasi 0 C to 70 C
Bilangan Pin 8 pins
Shutdown Function Yes

Panduan Konfigurasi Pin TLV2471CD 8-pin soic (d)

Konfigurasi pin untuk TLV2471CD (8-pin soic (d) pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8-pin soic (d) untuk TLV2471CD

Tiada data garisan pin yang diperoleh untuk TLV2471CD.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

TLV2471CD patut untuk 6 aplikasis: Battery-Powered Sensor Conditioning, Low-Side Current Sensing, Portable Medical Monitoring, Industrial Data Acquisition, Communications Signal Buffering, Audio and Control Loops.

🧩

Battery-Powered Sensor Conditioning

The TLV2471CD fits battery-powered sensor interfaces that need more bandwidth than a micropower amplifier while keeping supply consumption low. Its 600 uA per-channel supply current limits the amplifier's contribution to standby load, and rail-to-rail input and output operation helps preserve signal range in low-voltage systems. A typical circuit buffers or amplifies the output of a resistive sensor before an ADC. The 2.8 MHz gain-bandwidth product is substantially above the signal rate of many temperature, pressure, and occupancy sensors. Design checks should include sensor source impedance, ADC input range, output swing at the selected supply, and the duty cycle of the overall measurement cycle.

⚡

Low-Side Current Sensing

The TLV2471CD can amplify the small voltage developed across a low-side current-sense resistor while its 2.8 MHz gain-bandwidth product preserves moderate-frequency signal content. Rail-to-rail input operation is useful when the shunt voltage occupies much of the available signal range near a ground-referenced supply rail. In a typical application, the amplifier raises the shunt differential voltage and drives an ADC or measurement comparator. Engineers should verify the input differential voltage, common-mode range, output swing, resistor tolerance, and the offset contribution relative to the smallest current that must be measured.

💊

Portable Medical Monitoring

The TLV2471CD is applicable to portable monitoring equipment where a sensor front end must operate from a compact, low-voltage supply. Its 600 uA supply current per channel and 2.8 MHz bandwidth provide a practical balance between continuous power use and signal-handling capability, while rail-to-rail input and output behavior improves utilization of the available supply range. A typical use is conditioning a bridge, biopotential, or physiological sensor before digitization. The complete medical system must still address noise, input protection, isolation, leakage, applicable safety requirements, and the accuracy needed for its measurement rather than relying on the amplifier's general-purpose status alone.

🏭

Industrial Data Acquisition

The TLV2471CD is well suited to general-purpose industrial data-acquisition blocks that require rail-to-rail input and output operation at a 6 V maximum supply. A single amplifier can buffer sensor lines, amplify transducer outputs, or provide active filtering around an ADC input. Its 2.8 MHz gain-bandwidth product supports moderate-frequency signals, and 600 uA per channel can be valuable in distributed or multi-channel acquisition equipment. Because the commercial-temperature TLV2471CD is specified from 0 C to 70 C, installations with wider temperature ranges should use an appropriately qualified ordering option. Front-end design must also control grounding, noise, and common-mode excursions.

🌐

Communications Signal Buffering

The TLV2471CD can serve as a rail-to-rail buffer or gain stage in a low-voltage communications interface. Its 2.8 MHz gain-bandwidth product supports higher-frequency signal paths than a very-low-power amplifier, while the 600 uA supply current per channel helps constrain power in portable or distributed communications equipment. The part may be placed between a driver and receiver, at an ADC input, or in a feedback network around an active filter. Because it is a general-purpose single amplifier, the completed circuit should verify output-current capability, capacitive-load stability, channel separation, and timing margin against the actual communication waveform.

🎧

Audio and Control Loops

The TLV2471CD can be used in modest audio and feedback-control paths where low supply current, rail-to-rail operation, and 2.8 MHz bandwidth are more useful than very high slew rate. A typical control application places the amplifier in an active feedback loop, while an audio application can use it as a low-level buffer or filter stage. Rail-to-rail output capability increases headroom in a single-supply design, and the 600 uA supply current can simplify power-budget calculations. Designers should examine noise, output swing, distortion at the required signal level, loop stability, and whether the bandwidth is adequate for the control dynamics or audio bandwidth.

What is the TLV2471CD?
The TLV2471CD is a single, 6 V, 2.8 MHz rail-to-rail input and output CMOS operational amplifier from Texas Instruments. According to the manufacturer product page, the device is offered in an 8-pin SOIC package and consumes 600 uA per channel. It is intended for low-voltage signal-conditioning, sensing, buffering, and control applications where rail-to-rail operation and moderate AC performance are important.
What are the key specifications of TLV2471CD that engineers should know?
The key TLV2471CD specifications are single-channel operation, a 6 V maximum supply, 2.8 MHz gain-bandwidth product, 600 uA supply current per channel, and rail-to-rail input and output behavior. Texas Instruments identifies the device as a CMOS operational amplifier in an 8-pin SOIC package. Its 0 C to 70 C ordering range makes it suitable for commercial-temperature equipment, while precision offset, noise, and output-current limits should be confirmed from the manufacturer datasheet.
Where can I download the TLV2471CD datasheet PDF?
The official TLV2471CD datasheet can be obtained from the Texas Instruments product page or the manufacturer datasheet link. The manufacturer describes the TLV2471 as a single, 6 V, 2.8 MHz rail-to-rail input and output operational amplifier. Use the TLV2471 family document for the electrical characteristics, pin descriptions, typical application circuits, ordering information, and package drawings applicable to the TLV2471CD.
Where can I find the TLV2471CD pinout?
The TLV2471CD pinout is published in the Texas Instruments TLV2471 family datasheet, which shows the 8-pin SOIC connection diagram and pin table. Texas Instruments identifies the TLV2471CD as an 8-pin SOIC device. Use that diagram when assigning the supply, ground, input, output, and shutdown connections, and verify the exposed package dimensions and recommended land pattern before fabrication.
Is the TLV2471CD suitable for battery-powered sensor applications?
The TLV2471CD is suitable for many battery-powered sensor interfaces because it consumes 600 uA per channel and supports rail-to-rail input and output operation. Texas Instruments identifies it as a single, 6 V, 2.8 MHz CMOS operational amplifier. Its bandwidth is adequate for many moderate-frequency sensing paths, while battery life also depends on the sensor, regulator, load, duty cycle, and total application leakage.
TLV2471CD vs TLV2471AIDR — which is better for automotive use?
TLV2471AIDR is the more appropriate candidate for automotive use because the AIDR ordering option denotes the automotive-qualified version, while TLV2471CD is specified for 0 C to 70 C commercial-temperature operation. Both devices use the same 8-pin SOIC format and belong to the TLV2471 family. Before substitution, verify the automotive qualification, temperature range, electrical limits, and shutdown behavior in the manufacturer documentation.
What is the difference between TLV2471CD and TLV2471ID?
The principal documented ordering difference between TLV2471CD and TLV2471ID is their temperature grade: TLV2471CD is specified for 0 C to 70 C, while TLV2471ID extends to the industrial temperature range. Both are single 6 V, 2.8 MHz rail-to-rail CMOS operational amplifiers in 8-pin SOIC packages with 600 uA supply current per channel. Verify the complete electrical tables before treating either ordering option as a replacement.
When should I choose TLV2471CD over TLV2471AIDR?
Choose TLV2471CD when the circuit operates within the commercial 0 C to 70 C range and does not require the automotive-qualified ordering option. Choose TLV2471AIDR when the design requires automotive qualification or a broader environmental range. Both use the same 8-pin SOIC footprint, so the distinction is primarily qualification and temperature coverage rather than a change in the basic amplifier function.
Is TLV2471CD suitable for low-side current sensing?
The TLV2471CD is suitable for many low-side current-sensing circuits because its rail-to-rail input and output operation supports small signals around a low-side shunt. Its 2.8 MHz gain-bandwidth product provides more signal bandwidth than a typical micropower amplifier. The completed design must still verify common-mode limits, shunt-induced offset, output swing, gain error, and whether the selected gain produces stable operation.
What can replace TLV2471CD?
TLV2471AIDR and TLV2471ID are the closest documented same-family replacements for many TLV2471CD sockets because they use the 8-pin SOIC format and retain the TLV2471 amplifier architecture. TLV2471CD covers 0 C to 70 C, TLV2471ID covers the industrial range, and TLV2471AIDR provides the automotive-qualified ordering option. Verify every electrical limit and the shutdown pin before replacing a part in production equipment.
What is the best Texas Instruments equivalent for TLV2471CD?
TLV2471AIDR is the best same-family Texas Instruments option when an automotive-qualified part is required, while TLV2471ID is preferable when industrial-temperature coverage is needed. Each uses an 8-pin SOIC package and supports the same 6 V, 2.8 MHz, rail-to-rail operational-amplifier concept. The appropriate choice depends on qualification requirements, operating temperature, production conditions, and any order-code-specific changes.
Does the TLV2471CD support shutdown?
Yes, the TLV2471 family includes a shutdown function, as identified in the Texas Instruments family documentation. The TLV2471CD combines that function with 2.8 MHz gain-bandwidth product, 600 uA supply current per channel, and rail-to-rail input and output operation. Confirm the shutdown logic levels, timing, and inactive-state behavior in the manufacturer pin and electrical tables before using the function in a power-sequencing circuit.
Is TLV2471CD in stock and what is its lead time?
Current stock, minimum order quantity, and lead time should be confirmed through the Request a Quote form on this page. Texas Instruments lists TLV2471CD as an orderable 8-pin SOIC device, while channel inventory can change. Providing the required quantity, target date, and approved source in the quote request enables a current supply assessment without relying on an outdated stock indication.
How much does TLV2471CD cost?
Use the Request a Quote form on this page for the current TLV2471CD unit price and quantity pricing. Commercial terms can vary with volume, package quantity, delivery date, and supply conditions. The manufacturer ordering page identifies TLV2471CD as the commercial-temperature, 8-pin SOIC version, so include that exact ordering code in the request to avoid confusion with industrial or automotive variants.
Where can I buy TLV2471CD online?
The Request a Quote form on this page is the preferred route for obtaining TLV2471CD and current commercial terms. Submit the exact MPN, required quantity, shipping destination, and target delivery date. Texas Instruments identifies TLV2471CD as the single, 6 V, 2.8 MHz rail-to-rail operational amplifier in an 8-pin SOIC package, allowing the quote request to identify the correct orderable device.

Data referensi kejuruteraan untuk TLV2471CD — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose TLV2471CD for commercial-temperature, single-amplifier designs that need a 6 V maximum supply, 2.8 MHz gain-bandwidth product, rail-to-rail input and output operation, and 600 uA supply current per channel. Its 8-pin SOIC package makes it appropriate for conventional PCB layouts requiring one amplifier per package. Choose TLV2471ID when industrial-temperature coverage is required, or TLV2471AIDR when an automotive-qualified ordering option is needed. The TLV2471AID and TLV2471IP family options provide matching package and core amplifier characteristics for automotive and industrial requirements, respectively. TLV2471CP is the closest commercial-temperature family option. Before replacing any of these parts, verify the exact order-code electrical table, shutdown behavior, temperature grade, qualification, package drawing, and sourcing conditions.

Perbandingan dengan Gantian

Parametr Produk Ini TLV2471AIDR TLV2471ID TLV2471AID TLV2471IP TLV2471CP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D) 8-pin SOIC (D)
Number of Channels 1 channel 1 channel 1 channel 1 channel 1 channel 1 channel
Supply Voltage Up to 6 V Up to 6 V Up to 6 V Up to 6 V Up to 6 V Up to 6 V
Gain-Bandwidth Product 2.8 MHz 2.8 MHz 2.8 MHz 2.8 MHz 2.8 MHz 2.8 MHz
Supply Current 600 uA per channel 600 uA per channel 600 uA per channel 600 uA per channel 600 uA per channel 600 uA per channel
Input Common-Mode Range Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Shutdown Function Yes Yes Yes Yes Yes Yes

Penyeberangsung Jelas

  • Low-power operation combined with moderate AC bandwidth (vsTLV2471CP)
  • Commercial-temperature ordering option in an 8-pin SOIC package (vsTLV2471ID)
  • Automotive-qualified same-family path without changing the footprint (vsTLV2471AIDR)

Catatan Desain

Place the supply-bypass capacitor close to the TLV2471CD power and ground pins, and keep the input and feedback traces short to reduce parasitic coupling. Follow the manufacturer package drawing for the SOIC land pattern and pin orientation. If the amplifier drives a cable, connector, or ADC sampling network, route the sensitive input separately from fast output and switching-supply paths.

Do not treat rail-to-rail input and output wording as an unlimited operating range. The usable signal range still depends on the exact supply voltage, output load, input and output conditions, and the ordering option. Verify common-mode voltage, output swing, load current, and stability against the manufacturer electrical tables before using the amplifier near a supply rail.

Estimated: the amplifier's stated supply current is 600 uA per channel. At a 6 V supply, the amplifier supply-power contribution is approximately 6 V multiplied by 600 uA, or 3.6 mW, before considering output load current and external-circuit losses. Actual system power depends on the operating supply voltage, load, duty cycle, regulator efficiency, and the selected ordering option.

Use a feedback network appropriate for the required closed-loop bandwidth, because the TLV2471CD has 2.8 MHz gain-bandwidth product. Check loop gain and phase margin at the target gain, especially with capacitive loading from long PCB traces, ADC inputs, or cable capacitance. Add an isolation resistor close to the output when driving capacitive loads and verify stability experimentally.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The TLV2471CD is the commercial-temperature ordering option; use an automotive-qualified ordering option when AEC-Q100 qualification is required. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact MPN.

Data disahkan pada: 2026-11-15 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

TLV2471CD datasheet TLV2471CD pinout TLV2471CD datasheet pdf TLV2471CD equivalent TLV2471CD replacement TLV2471CD vs TLV2471AIDR TLV2471CD vs TLV2471ID TLV2471CD price TLV2471CD stock Texas Instruments TLV2471CD TLV2471CD 8-SOIC footprint TLV2471CD 2.8MHz amplifier

Komponen dan Tanda berkaitan

Texas Instruments TLV2471CD TLV2471AIDR TLV2471ID TLV2471AID TLV2471IP TLV2471CP operational amplifier CMOS operational amplifier rail-to-rail input rail-to-rail output single amplifier 2.8 MHz gain-bandwidth product 600 uA supply current 8-pin SOIC SOIC package family surface-mount package signal conditioning low-side current sensing battery-powered instrumentation industrial data acquisition shutdown function Texas Instruments TLV2471 family
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ