TLV2471CD - 2.8MHz RRIO Op Amp | Texas Instruments
MPN: TLV2471CD ✓ פעילTLV2471CD סקירה
An operational amplifier is a voltage-gain building block used for signal conditioning, feedback control, buffering, and analog computation. The TLV2471 belongs to the CMOS operational-amplifier hierarchy, where rail-to-rail input and output operation supports signals close to the supply rails. This makes it useful in portable instrumentation, sensor interfaces, battery-powered monitoring, communications, and industrial control systems.
The principal operating characteristics include single-supply operation up to 6 V, 2.8 MHz gain-bandwidth product, and approximately 600 uA supply current per channel. Rail-to-rail input and output capability increases usable signal range in low-voltage systems. The single-amplifier configuration also keeps the SOIC-8 package appropriate where one amplifier per package offers a practical balance between functionality and board area.
The TLV247x family uses CMOS technology to combine low bias consumption with useful AC performance. Its 2.8 MHz bandwidth supports moderate-frequency signal paths and closed-loop applications requiring more bandwidth than a micropower amplifier, while the 600 uA supply requirement preserves low-power system budgets. Exact offset, input-bias-current, noise, output-current, and overload-recovery figures should be taken from the manufacturer datasheet for the selected operating conditions.
Typical uses include low-side current sensing, portable sensor conditioning, buffered ADC inputs, audio and communication signal paths, and feedback control loops. In a current-sense amplifier, the 2.8 MHz bandwidth helps preserve the useful bandwidth of the measured signal. In a portable sensor interface, low supply consumption reduces the load on the battery while rail-to-rail operation accommodates a broad input range.
Design the decoupling network with short traces and place the supply capacitor close to the device. Check output-current limits, input common-mode range, output swing, stability, and noise requirements at the intended supply voltage and load before finalizing the bias point. The manufacturer pin description and package drawing should be used when assigning PCB tracks and selecting bypass-capacitor placement.
This page combines the manufacturer device description, package and ordering information, commercial guidance, and practical engineering guidance for the TLV2471CD. It also identifies same-family drop-in options and highlights the parameters that must be checked before replacing an amplifier in an existing SOIC-8 design.
חלופות תחליף ישיר עבור TLV2471CD — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TLV2471CD (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Package, Operating Temperature Range, Technology.
TLV2471AIDR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2471ID
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TLV2471AID
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2471IP
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2471CP
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←TLV2471CD דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Single operational amplifier |
| מתח אספקה | Up to 6 V |
| Gain-Bandwidth Product | 2.8 MHz |
| זרם אספקה | 600 uA per channel |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Process Technology | CMOS |
| Number of Channels | 1 channel |
| מארז | 8-pin SOIC (D) |
| סוג הרכבה | Surface mount |
| טווח טמפרטורת פעולה | 0 C to 70 C |
| מספר פינים | 8 pins |
| Shutdown Function | Yes |
מדריך תצורת פינים של TLV2471CD 8-pin soic (d)
תצורת פינים עבור TLV2471CD (מארזת 8-pin soic (d)). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור TLV2471CD.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
TLV2471CD מתאים עבור 6 יישוםs: Battery-Powered Sensor Conditioning, Low-Side Current Sensing, Portable Medical Monitoring, Industrial Data Acquisition, Communications Signal Buffering, Audio and Control Loops.
Battery-Powered Sensor Conditioning
The TLV2471CD fits battery-powered sensor interfaces that need more bandwidth than a micropower amplifier while keeping supply consumption low. Its 600 uA per-channel supply current limits the amplifier's contribution to standby load, and rail-to-rail input and output operation helps preserve signal range in low-voltage systems. A typical circuit buffers or amplifies the output of a resistive sensor before an ADC. The 2.8 MHz gain-bandwidth product is substantially above the signal rate of many temperature, pressure, and occupancy sensors. Design checks should include sensor source impedance, ADC input range, output swing at the selected supply, and the duty cycle of the overall measurement cycle.
מומלץ
Low-Side Current Sensing
The TLV2471CD can amplify the small voltage developed across a low-side current-sense resistor while its 2.8 MHz gain-bandwidth product preserves moderate-frequency signal content. Rail-to-rail input operation is useful when the shunt voltage occupies much of the available signal range near a ground-referenced supply rail. In a typical application, the amplifier raises the shunt differential voltage and drives an ADC or measurement comparator. Engineers should verify the input differential voltage, common-mode range, output swing, resistor tolerance, and the offset contribution relative to the smallest current that must be measured.
מומלץ
Portable Medical Monitoring
The TLV2471CD is applicable to portable monitoring equipment where a sensor front end must operate from a compact, low-voltage supply. Its 600 uA supply current per channel and 2.8 MHz bandwidth provide a practical balance between continuous power use and signal-handling capability, while rail-to-rail input and output behavior improves utilization of the available supply range. A typical use is conditioning a bridge, biopotential, or physiological sensor before digitization. The complete medical system must still address noise, input protection, isolation, leakage, applicable safety requirements, and the accuracy needed for its measurement rather than relying on the amplifier's general-purpose status alone.
מומלץ
Industrial Data Acquisition
The TLV2471CD is well suited to general-purpose industrial data-acquisition blocks that require rail-to-rail input and output operation at a 6 V maximum supply. A single amplifier can buffer sensor lines, amplify transducer outputs, or provide active filtering around an ADC input. Its 2.8 MHz gain-bandwidth product supports moderate-frequency signals, and 600 uA per channel can be valuable in distributed or multi-channel acquisition equipment. Because the commercial-temperature TLV2471CD is specified from 0 C to 70 C, installations with wider temperature ranges should use an appropriately qualified ordering option. Front-end design must also control grounding, noise, and common-mode excursions.
מומלץ
Communications Signal Buffering
The TLV2471CD can serve as a rail-to-rail buffer or gain stage in a low-voltage communications interface. Its 2.8 MHz gain-bandwidth product supports higher-frequency signal paths than a very-low-power amplifier, while the 600 uA supply current per channel helps constrain power in portable or distributed communications equipment. The part may be placed between a driver and receiver, at an ADC input, or in a feedback network around an active filter. Because it is a general-purpose single amplifier, the completed circuit should verify output-current capability, capacitive-load stability, channel separation, and timing margin against the actual communication waveform.
מומלץ
Audio and Control Loops
The TLV2471CD can be used in modest audio and feedback-control paths where low supply current, rail-to-rail operation, and 2.8 MHz bandwidth are more useful than very high slew rate. A typical control application places the amplifier in an active feedback loop, while an audio application can use it as a low-level buffer or filter stage. Rail-to-rail output capability increases headroom in a single-supply design, and the 600 uA supply current can simplify power-budget calculations. Designers should examine noise, output swing, distortion at the required signal level, loop stability, and whether the bandwidth is adequate for the control dynamics or audio bandwidth.
מומלץ
נתוני עזר הנדסיים עבור TLV2471CD — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TLV2471AIDR | TLV2471ID | TLV2471AID | TLV2471IP | TLV2471CP |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Number of Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Supply Voltage | Up to 6 V | Up to 6 V | Up to 6 V | Up to 6 V | Up to 6 V | Up to 6 V |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Supply Current | 600 uA per channel | 600 uA per channel | 600 uA per channel | 600 uA per channel | 600 uA per channel | 600 uA per channel |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shutdown Function | Yes | Yes | Yes | Yes | Yes | Yes |
מבדילים עיקריים
- Low-power operation combined with moderate AC bandwidth (לעומתTLV2471CP)
- Commercial-temperature ordering option in an 8-pin SOIC package (לעומתTLV2471ID)
- Automotive-qualified same-family path without changing the footprint (לעומתTLV2471AIDR)
הערות תכנון
Place the supply-bypass capacitor close to the TLV2471CD power and ground pins, and keep the input and feedback traces short to reduce parasitic coupling. Follow the manufacturer package drawing for the SOIC land pattern and pin orientation. If the amplifier drives a cable, connector, or ADC sampling network, route the sensitive input separately from fast output and switching-supply paths.
Do not treat rail-to-rail input and output wording as an unlimited operating range. The usable signal range still depends on the exact supply voltage, output load, input and output conditions, and the ordering option. Verify common-mode voltage, output swing, load current, and stability against the manufacturer electrical tables before using the amplifier near a supply rail.
Estimated: the amplifier's stated supply current is 600 uA per channel. At a 6 V supply, the amplifier supply-power contribution is approximately 6 V multiplied by 600 uA, or 3.6 mW, before considering output load current and external-circuit losses. Actual system power depends on the operating supply voltage, load, duty cycle, regulator efficiency, and the selected ordering option.
Use a feedback network appropriate for the required closed-loop bandwidth, because the TLV2471CD has 2.8 MHz gain-bandwidth product. Check loop gain and phase margin at the target gain, especially with capacitive loading from long PCB traces, ADC inputs, or cable capacitance. Add an isolation resistor close to the output when driving capacitive loads and verify stability experimentally.
מידע על תאימות
The TLV2471CD is the commercial-temperature ordering option; use an automotive-qualified ordering option when AEC-Q100 qualification is required. No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact MPN.