Texas Instruments

TLV2760ID - 500kHz RRIO Op Amp with Shutdown | Texas Instruments

MPN: TLV2760ID ✓ Aktif
3.6 V Vdss 20 µA Id 8-pin SOIC Package
MOQ: 1 |

TLV2760ID Ringkasan

The Texas Instruments TLV2760ID is a single, micropower rail-to-rail input and output operational amplifier with shutdown, 500 kHz gain-bandwidth product, 20 µA typical supply current, and a maximum supply voltage of 3.6 V. It is housed in an 8-pin SOIC package and is intended for low-voltage, low-power signal-conditioning systems.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Rail-to-rail input and output, commonly abbreviated RRIO, allows the input common-mode range and output swing to approach the supply rails. This makes the TLV2760ID useful in portable instrumentation, sensor interfaces, battery-powered monitoring, and low-voltage control systems where the usable signal range is limited.

Key characteristics include a 500 kHz bandwidth, operation down to 1.8 V, a 3.6 V maximum recommended supply voltage, and approximately 20 µA of supply current. The shutdown function provides a way to reduce power consumption when the amplifier is not needed. According to the manufacturer datasheet, the TLV2760ID is specified for an industrial temperature range of -40°C to +85°C and offers 3500 µV typical input offset voltage.

The TLV2760ID combines a single amplifier with rail-to-rail inputs and outputs in an 8-pin SOIC footprint. Its 500 kHz bandwidth is sufficient for general-purpose signal conditioning, active filtering, low-frequency sensor amplification, and embedded analog measurement. The shutdown control makes it particularly useful in duty-cycled systems where the analog channel must be disabled between measurements.

Typical applications include battery-operated sensor interfaces, portable medical monitoring, industrial control modules, low-voltage data acquisition, buffer stages, and active filters. Its 1.8 V minimum operating supply supports systems powered from one lithium cell or from low-voltage energy-harvesting rails. The maximum recommended supply of 3.6 V prevents accidental operation from a higher-voltage source without proper regulation.

When using the TLV2760ID, check the input and output common-mode limits for the actual supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and the shutdown logic must remain in a defined state during startup. Output loading and capacitive loads can affect stability, so verify the final circuit against the application information in the manufacturer datasheet.

This page combines the principal electrical and packaging details with application guidance, design checks, and carefully qualified replacement options. It also highlights where shutdown polarity, supply voltage, bandwidth, and package compatibility must be reviewed before treating another amplifier as a true drop-in replacement.

Pilihan pengganti yang segera untuk TLV2760ID — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera TLV2760ID (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type, Package, Operating Temperature Range, Input Common-Mode Range, Supply Voltage Range.

Texas Instruments
Amplifier Type: General Purpose Operational Amplifier, Rail-to-Rail Input/Output
Package: 8-SOIC (0.154 in, 3.90 mm width)
Operating Temperature Range: 0 °C to 70 °C
Bandingkan Dengan TLV2760ID →
Texas Instruments
Amplifier Type: Single voltage-feedback operational amplifier
Package: 8-pin SOIC (D)
Supply Voltage Range: 1.8 V to 3.6 V recommended maximum
Bandingkan Dengan TLV2760ID →

TLV2761ID

✅ Masuk Drop-In ⚠️ Spesifikasi Tidak Disahkan
Texas Instruments
📦 8-pin SOIC
Single voltage-feedback operational amplifier · 1 circuit · 1.8 V to 3.6 V recommended maximum · 3.6 V · 1.8 V · 500 kHz · 20 µA · Rail-to-rail input

Hubungi untuk harga

Lihat Datasheet →

TLV2760ID Penilaian maksimum & Ciri-ciri Elektrik

Amplifier Type 1 circuit operational amplifier
Maximum Recommended Supply Voltage 3.6 V
Minimum Operating Supply Voltage 1.8 V
Gain-Bandwidth Product 500 kHz
Typical Supply Current 20 µA
Input Offset Voltage 3500 µV typical
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Shutdown Function 1 shutdown control function
Gambaran Suhu Operasi -40°C to +85°C
Kemasan 8-pin SOIC
Jenis Pemasangan Surface mount
Supply Voltage Characterization Single supply operation

Konfigurasi Pin TLV2760ID

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OUT — Amplifier output
Pin 2 V- — Negative supply or ground connection
Pin 3 V+ — Positive supply connection
Pin 4 SD — Shutdown control input
Pin 5 NC — Not connected
Pin 6 IN- — Inverting input
Pin 7 IN+ — Non-inverting input
Pin 8 NC — Not connected

Aplikasi Biasa

TLV2760ID patut untuk 6 aplikasis: Battery-Powered Sensor Signal Conditioning, Portable Medical Monitoring, Industrial Sensor Interface, Low-Power Active Filtering, Portable Data Acquisition, Low-Voltage Embedded Control.

🔋

Battery-Powered Sensor Signal Conditioning

The TLV2760ID is well suited to conditioning signals from low-voltage sensors because it operates from 1.8 V, consumes approximately 20 µA, and accepts inputs through a rail-to-rail common-mode range. Place the amplifier close to the sensor output to minimize pickup and board contamination before filtering or level shifting. A 1.8 V system allows nearly the full sensor output span to reach the input stage. The design must still account for the amplifier's 3500 µV typical input offset, input bias effects, and settling time. Shutdown can disable the channel between measurements when the sensor itself remains active.

💊

Portable Medical Monitoring

The TLV2760ID can serve as a low-power gain or buffer stage in portable monitoring equipment operating from a 1.8 V to 3.6 V supply. Its rail-to-rail input and output characteristics preserve weak biological-sensor signals without requiring a higher-voltage amplifier or an additional signal-range translation stage. The approximately 20 µA supply current helps limit energy use in wearable and handheld systems. Validate input bias current, noise, common-mode behavior, and output settling for the selected electrode or sensor. Medical-system qualification also requires application-specific safety and quality controls beyond the component temperature rating.

🏭

Industrial Sensor Interface

The TLV2760ID provides a compact analog front end for low-voltage industrial sensors whose signals span most of the available supply range. Rail-to-rail inputs accept signals near either supply rail, while the rail-to-rail output allows greater use of the 3.6 V maximum operating supply. Its 500 kHz gain-bandwidth product supports general-purpose amplification and first-order active filtering rather than demanding high-speed instrumentation performance. Use short, guarded traces and a single-point ground strategy to reduce noise pickup, and verify offset accuracy against the smallest signal that must be resolved. The -40°C to +85°C rating supports industrial temperature environments.

📡

Low-Power Active Filtering

The TLV2760ID can implement active filters and gain blocks in portable or low-voltage acquisition systems. Its 500 kHz bandwidth gives sufficient loop bandwidth for many audio-band, control-band, and low-frequency sensor applications, while approximately 20 µA supply current supports constrained power budgets. Gain-bandwidth, noise, and load stability must be checked against the actual filter topology, especially at high Q or with capacitive loading. Place input, feedback, and compensation components close to the amplifier to minimize parasitic feedback. If the amplifier is only active during a measurement interval, use the shutdown control to reduce system consumption.

🖥️

Portable Data Acquisition

The TLV2760ID is appropriate for multiplexing small, low-amplitude signals in compact data-acquisition equipment operating at 1.8 V or above. Rail-to-rail inputs increase the usable range for sensor channels, and the 500 kHz bandwidth supports conditioning signals below the acquisition system's full conversion bandwidth. The amplifier's offset and bias characteristics must be included in the error budget for high-resolution measurements. Place it near the analog input connector or multiplexer to avoid adding noise after the signal has been amplified. Shutdown is useful when multiple channels are sampled sequentially and inactive channels must consume less power.

🤖

Low-Voltage Embedded Control

The TLV2760ID can condition analog feedback or monitoring signals in embedded systems powered by 1.8 V to 3.6 V. Its approximately 20 µA supply current is valuable in battery-operated controllers, while the shutdown terminal permits direct connection to a microcontroller or power-management signal. Rail-to-rail operation allows the amplifier to work with ADC inputs that use nearly the complete supply range. Confirm logic compatibility of the shutdown control, check the output drive required by the ADC input, and maintain a stable reference for ratiometric measurements. The amplifier should be decoupled locally to prevent supply perturbations from affecting the controlled system.

What are the key specifications of TLV2760ID that engineers should know?
The TLV2760ID is a single RRIO operational amplifier with 500 kHz gain-bandwidth product, 20 µA typical supply current, operation down to 1.8 V, and a 3.6 V maximum recommended supply. It includes shutdown and comes in an 8-pin SOIC package. According to the Texas Instruments datasheet, the industrial-grade TLV2760ID is specified from -40°C to +85°C, with typical input offset voltage of 3500 µV. These characteristics place it in the micropower, low-voltage general-purpose amplifier category.
What is the operating voltage range of TLV2760ID?
The TLV2760ID operates from 1.8 V up to the 3.6 V maximum recommended supply voltage. According to the Texas Instruments datasheet, the family is characterized down to 1.8 V, allowing operation from two alkaline cells, one lithium cell, or a regulated low-voltage rail. The 3.6 V maximum is a recommended operating limit and should not be exceeded without additional device-specific protection or a higher-voltage-rated amplifier.
Where can I download the TLV2760ID datasheet PDF?
The official TLV2760ID datasheet PDF is available from the Texas Instruments document link on this page. It contains the complete electrical characteristics, ordering information, pin configuration, typical performance curves, application guidance, and family comparison for the TLV276x micropower operational amplifiers. Use the manufacturer document rather than an unofficial mirror when determining pin functions, shutdown behavior, input range, output swing, or recommended decoupling.
Where can I find the TLV2760ID pinout?
The TLV2760ID pin configuration is shown in the pin-description table and package drawing in the Texas Instruments datasheet. The device uses an 8-pin SOIC package, with pins assigned to the output, supply rails, input terminals, shutdown control, and no-connect positions. Use that manufacturer pin table when assigning PCB tracks because the SOIC footprint alone does not establish the functional meaning of every terminal.
What does RRIO mean for the TLV2760ID?
RRIO means that both the input common-mode range and the output swing extend toward the positive and negative supply rails. The TLV2760ID therefore accepts input signals close to its supply limits and can produce output swing near those limits, subject to output load and headroom. According to the Texas Instruments datasheet, this rail-to-rail behavior is useful in low-voltage systems where conventional input and output ranges would waste much of the available signal span.
Why should I choose the TLV2760ID for a low-voltage sensor interface?
The TLV2760ID fits low-voltage sensor interfaces because it operates down to 1.8 V, draws approximately 20 µA, and provides rail-to-rail input and output behavior. Those characteristics preserve signal range in battery-powered systems and permit a direct interface to sensors whose output approaches either supply rail. Confirm that the sensor output, amplifier gain, settling requirements, and shutdown timing remain within the device's electrical limits.
What can replace the TLV2760ID?
The closest qualified same-package replacement is the Texas Instruments TLV2761ID, which uses the same 8-pin SOIC format and belongs to the same micropower RRIO family. Its shutdown-control behavior must be checked against the original circuit because the family offers different shutdown options. Cross-brand drop-in alternatives were not established from the available manufacturer and distributor information, so a replacement should not be selected solely by matching the SOIC-8 package.
Is the TLV2761ID the same as the TLV2760ID?
The TLV2761ID is a close family member of the TLV2760ID and is packaged in the same 8-pin SOIC format, but it is not necessarily interchangeable in every circuit. The principal selection issue is the shutdown-control configuration and associated logic requirements. According to the family datasheet, engineers should compare the pin descriptions, supply current, and shutdown polarity before treating the TLV2761ID as a drop-in substitution.
When should I choose TLV2760ID over TLV2761ID?
Choose the TLV2760ID when the circuit requires the specific shutdown-control polarity and functional behavior of that device; choose the TLV2761ID when its shutdown configuration better matches the available control logic. Both are low-voltage, micropower, rail-to-rail amplifiers in the 8-pin SOIC family. The decision should be based on the family pin table and electrical table rather than package appearance, especially when shutdown is used during periodic sampling.
Is TLV2760ID suitable for battery-powered equipment?
Yes, the TLV2760ID is suitable for battery-powered equipment because its supply current is approximately 20 µA and its operating supply can be as low as 1.8 V. Shutdown can further reduce consumption when the measurement channel is inactive. For a complete battery design, also evaluate the shutdown-state current, sensor quiescent current, regulator efficiency, leakage at the input, and the system duty cycle; the amplifier rating alone does not determine total battery life.
Where can I buy TLV2760ID online and check its availability?
Use the Request a Quote form on this page to ask about TLV2760ID availability, order quantity, and lead time for the 8-pin SOIC device. The form allows purchasing teams to request current commercial confirmation without relying on a static listing or an outdated inventory record. Engineers should include the required quantity, target delivery date, and acceptable packaging details in the request.
What is the price of TLV2760ID?
Use the Request a Quote form on this page for the current TLV2760ID price and quantity availability. Commercial pricing can vary with order quantity, packaging, production volume, and supply conditions, so a static figure should not be used for budgeting or purchasing approval. Include the required part number TLV2760ID and your target order quantity to receive a current quotation.
What is the lead time for TLV2760ID?
Request the current lead time and minimum order quantity for TLV2760ID through the Request a Quote form on this page. Lead time can change with manufacturer production conditions and order size, so a schedule commitment should be obtained for the planned quantity rather than inferred from a generic catalog entry. Include the required delivery date and any acceptable alternate assembly schedule with the request.
Is TLV2760ID in stock?
Submit the TLV2760ID part number and required quantity through the Request a Quote form on this page to request current stock confirmation. The manufacturer lists the device as active, but real-time inventory and available production quantity should be confirmed for the specific order. For safety-stock planning, request both immediate availability and the expected replenishment lead time.
How should the TLV2760ID shutdown pin be handled?
Keep the TLV2760ID shutdown pin in a defined logic state during normal operation and startup so the amplifier does not enter an unintended state. Use the manufacturer pin table and shutdown timing information in the TLV276x datasheet to determine the required polarity and control sequence. If the shutdown function is unused, follow the manufacturer's explicit guidance for that pin rather than leaving it uncontrolled.
Does TLV2760ID meet RoHS and AEC-Q100 requirements?
The available manufacturer product information confirms the TLV2760ID identity, package, voltage range, bandwidth, and industrial temperature rating, but it does not explicitly state RoHS, REACH, or AEC-Q100 status on this page. Use the manufacturer product page and current compliance documentation for formal environmental or automotive qualification. The -40°C to +85°C industrial temperature range should not be interpreted as AEC-Q100 qualification.

Data referensi kejuruteraan untuk TLV2760ID — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the TLV2760ID when a low-voltage system needs a single RRIO amplifier, approximately 20 µA operating current, 500 kHz bandwidth, and an 8-pin SOIC footprint. It is particularly effective in 1.8 V to 3.6 V sensor, data-acquisition, filtering, and embedded-control applications where the signal approaches either supply rail. Choose the TLV2761ID only after confirming that its shutdown-control configuration and electrical limits satisfy the circuit; it is the closest same-family candidate, not an unconditional substitution. Packaging-only variants were excluded because they add no engineering selection value. No cross-brand amplifier was listed as a drop-in replacement because the available manufacturer and distributor information did not establish a pin-compatible, parameter-qualified SOIC-8 equivalent. For designs requiring lower offset, lower noise, faster settling, wider input range, or output drive beyond the TLV2760ID ratings, perform a new parametric and stability review rather than assuming that a common amplifier package guarantees equivalence.

Perbandingan dengan Gantian

Parametr Produk Ini TLV2761ID
Brand Texas Instruments Texas Instruments
Package 8-pin SOIC 8-pin SOIC
Amplifier Configuration Single amplifier with shutdown Single amplifier family member
Shutdown Control Shutdown function Different shutdown-control configuration

Penyeberangsung Jelas

  • Combines micropower operation with a 500 kHz bandwidth (vsTLV2761ID)
  • Supports operation from a 1.8 V supply (vsTLV2761ID)
  • Rail-to-rail input and output operation (vsTLV2761ID)

Catatan Desain

Place a local bypass capacitor at the positive supply pin and return it directly to the supply or ground reference through a short path. Keep the shutdown control in a defined state during startup so the amplifier does not enter an unintended shutdown condition. Because the typical operating supply current is approximately 20 µA, capacitor leakage and input bias current can become significant in high-impedance designs. Select low-leakage capacitors and verify that the sensor, protection network, and feedback components do not consume more current than the signal chain requires.

Do not treat an 8-pin SOIC footprint as proof of functional drop-in compatibility. Before substituting the TLV2761ID, compare the shutdown-control polarity, shutdown timing, input bias current, output swing, and stability behavior against the original circuit. Also verify the maximum recommended supply voltage of 3.6 V. A mechanically similar amplifier can reverse the shutdown state or fail to meet the required bias and offset performance even when its headline bandwidth rating appears suitable.

Route the non-inverting input directly to the signal source and keep the inverting feedback path short to reduce parasitic coupling and oscillation risk. Place the shutdown trace away from high-slew-rate clock and switching-node traces, and provide a defined pull state if the controlling signal can float. For high-impedance sensors, use a guarded input or small-area routing to reduce leakage and surface contamination. Review the final layout for supply bypassing, output-load stability, and exposed pad or ground requirements specified by the manufacturer package drawing.

The 500 kHz gain-bandwidth product is sufficient for many general-purpose signal-conditioning tasks, but closed-loop bandwidth depends on the selected noise gain and the amplifier's stability behavior. Check the required settling time at the signal frequency and the bandwidth needed to suppress out-of-band noise. Avoid driving large capacitive loads without confirming stability from the manufacturer data. If the application requires a wider closed-loop bandwidth or lower offset than the TLV2760ID provides, select a different amplifier rather than compensating through excessive gain.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

The available product information identifies the TLV2760ID as an industrial-temperature Texas Instruments amplifier but does not explicitly state the requested environmental or automotive compliance statuses. The -40°C to +85°C rating is not evidence of AEC-Q100 qualification.

Pencarian Berhubungan

TLV2760ID datasheet TLV2760ID pinout TLV2760ID datasheet pdf TLV2760ID equivalent TLV2760ID replacement TLV2760ID cross reference TLV2760ID vs TLV2761ID TLV2760ID price TLV2760ID stock Texas Instruments TLV2760ID TLV2760ID 500kHz amplifier TLV2760ID SOIC-8 pinout TLV2760ID low voltage sensor interface TLV2760ID shutdown pin

Komponen dan Tanda berkaitan

Texas Instruments TLV2760ID TLV2761ID TLV276x family operational amplifier single amplifier micropower amplifier rail-to-rail input and output RRIO shutdown control 500 kHz gain-bandwidth product 20 µA supply current 1.8 V minimum supply 3.6 V maximum recommended supply 8-pin SOIC SOIC family surface-mount package input offset voltage sensor signal conditioning battery-powered instrumentation portable medical monitoring industrial sensor interface active filtering Texas Instruments TLV2760 datasheet
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ