TLV2760ID - 500kHz RRIO Op Amp with Shutdown | Texas Instruments
MPN: TLV2760ID ✓ AktifTLV2760ID Ringkasan
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. Rail-to-rail input and output, commonly abbreviated RRIO, allows the input common-mode range and output swing to approach the supply rails. This makes the TLV2760ID useful in portable instrumentation, sensor interfaces, battery-powered monitoring, and low-voltage control systems where the usable signal range is limited.
Key characteristics include a 500 kHz bandwidth, operation down to 1.8 V, a 3.6 V maximum recommended supply voltage, and approximately 20 µA of supply current. The shutdown function provides a way to reduce power consumption when the amplifier is not needed. According to the manufacturer datasheet, the TLV2760ID is specified for an industrial temperature range of -40°C to +85°C and offers 3500 µV typical input offset voltage.
The TLV2760ID combines a single amplifier with rail-to-rail inputs and outputs in an 8-pin SOIC footprint. Its 500 kHz bandwidth is sufficient for general-purpose signal conditioning, active filtering, low-frequency sensor amplification, and embedded analog measurement. The shutdown control makes it particularly useful in duty-cycled systems where the analog channel must be disabled between measurements.
Typical applications include battery-operated sensor interfaces, portable medical monitoring, industrial control modules, low-voltage data acquisition, buffer stages, and active filters. Its 1.8 V minimum operating supply supports systems powered from one lithium cell or from low-voltage energy-harvesting rails. The maximum recommended supply of 3.6 V prevents accidental operation from a higher-voltage source without proper regulation.
When using the TLV2760ID, check the input and output common-mode limits for the actual supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and the shutdown logic must remain in a defined state during startup. Output loading and capacitive loads can affect stability, so verify the final circuit against the application information in the manufacturer datasheet.
This page combines the principal electrical and packaging details with application guidance, design checks, and carefully qualified replacement options. It also highlights where shutdown polarity, supply voltage, bandwidth, and package compatibility must be reviewed before treating another amplifier as a true drop-in replacement.
Alternatif penggantian untuk TLV2760ID — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian TLV2760ID (sama faktor bentuk dan footprint) — berbeda di dalam Amplifier Type, Package, Operating Temperature Range, Input Common-Mode Range, Supply Voltage Range.
TLV2761ID
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →TLV2760ID Rating Maksimal & Karakteristik Listrik
| Amplifier Type | 1 circuit operational amplifier |
| Maximum Recommended Supply Voltage | 3.6 V |
| Minimum Operating Supply Voltage | 1.8 V |
| Gain-Bandwidth Product | 500 kHz |
| Typical Supply Current | 20 µA |
| Input Offset Voltage | 3500 µV typical |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Function | 1 shutdown control function |
| Rentang Suhu Kerja | -40°C to +85°C |
| Paket | 8-pin SOIC |
| Tipe Mounting | Surface mount |
| Supply Voltage Characterization | Single supply operation |
Konfigurasi Pin TLV2760ID
| Pin produk 1 | OUT — Amplifier output |
| Pin produk 2 | V- — Negative supply or ground connection |
| Pin produk 3 | V+ — Positive supply connection |
| Pin produk 4 | SD — Shutdown control input |
| Pin produk 5 | NC — Not connected |
| Pin produk 6 | IN- — Inverting input |
| Pin produk 7 | IN+ — Non-inverting input |
| Pin produk 8 | NC — Not connected |
Aplikasi Umum
TLV2760ID cocok untuk 6 aplikasis: Battery-Powered Sensor Signal Conditioning, Portable Medical Monitoring, Industrial Sensor Interface, Low-Power Active Filtering, Portable Data Acquisition, Low-Voltage Embedded Control.
Battery-Powered Sensor Signal Conditioning
The TLV2760ID is well suited to conditioning signals from low-voltage sensors because it operates from 1.8 V, consumes approximately 20 µA, and accepts inputs through a rail-to-rail common-mode range. Place the amplifier close to the sensor output to minimize pickup and board contamination before filtering or level shifting. A 1.8 V system allows nearly the full sensor output span to reach the input stage. The design must still account for the amplifier's 3500 µV typical input offset, input bias effects, and settling time. Shutdown can disable the channel between measurements when the sensor itself remains active.
Direkomendasikan
Portable Medical Monitoring
The TLV2760ID can serve as a low-power gain or buffer stage in portable monitoring equipment operating from a 1.8 V to 3.6 V supply. Its rail-to-rail input and output characteristics preserve weak biological-sensor signals without requiring a higher-voltage amplifier or an additional signal-range translation stage. The approximately 20 µA supply current helps limit energy use in wearable and handheld systems. Validate input bias current, noise, common-mode behavior, and output settling for the selected electrode or sensor. Medical-system qualification also requires application-specific safety and quality controls beyond the component temperature rating.
Direkomendasikan
Industrial Sensor Interface
The TLV2760ID provides a compact analog front end for low-voltage industrial sensors whose signals span most of the available supply range. Rail-to-rail inputs accept signals near either supply rail, while the rail-to-rail output allows greater use of the 3.6 V maximum operating supply. Its 500 kHz gain-bandwidth product supports general-purpose amplification and first-order active filtering rather than demanding high-speed instrumentation performance. Use short, guarded traces and a single-point ground strategy to reduce noise pickup, and verify offset accuracy against the smallest signal that must be resolved. The -40°C to +85°C rating supports industrial temperature environments.
Direkomendasikan
Low-Power Active Filtering
The TLV2760ID can implement active filters and gain blocks in portable or low-voltage acquisition systems. Its 500 kHz bandwidth gives sufficient loop bandwidth for many audio-band, control-band, and low-frequency sensor applications, while approximately 20 µA supply current supports constrained power budgets. Gain-bandwidth, noise, and load stability must be checked against the actual filter topology, especially at high Q or with capacitive loading. Place input, feedback, and compensation components close to the amplifier to minimize parasitic feedback. If the amplifier is only active during a measurement interval, use the shutdown control to reduce system consumption.
Direkomendasikan
Portable Data Acquisition
The TLV2760ID is appropriate for multiplexing small, low-amplitude signals in compact data-acquisition equipment operating at 1.8 V or above. Rail-to-rail inputs increase the usable range for sensor channels, and the 500 kHz bandwidth supports conditioning signals below the acquisition system's full conversion bandwidth. The amplifier's offset and bias characteristics must be included in the error budget for high-resolution measurements. Place it near the analog input connector or multiplexer to avoid adding noise after the signal has been amplified. Shutdown is useful when multiple channels are sampled sequentially and inactive channels must consume less power.
Direkomendasikan
Low-Voltage Embedded Control
The TLV2760ID can condition analog feedback or monitoring signals in embedded systems powered by 1.8 V to 3.6 V. Its approximately 20 µA supply current is valuable in battery-operated controllers, while the shutdown terminal permits direct connection to a microcontroller or power-management signal. Rail-to-rail operation allows the amplifier to work with ADC inputs that use nearly the complete supply range. Confirm logic compatibility of the shutdown control, check the output drive required by the ADC input, and maintain a stable reference for ratiometric measurements. The amplifier should be decoupled locally to prevent supply perturbations from affecting the controlled system.
Direkomendasikan
Data referensi engineering untuk TLV2760ID — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | TLV2761ID |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC |
| Amplifier Configuration | Single amplifier with shutdown | Single amplifier family member |
| Shutdown Control | Shutdown function | Different shutdown-control configuration |
Diferensiator Kunci
- Combines micropower operation with a 500 kHz bandwidth (vsTLV2761ID)
- Supports operation from a 1.8 V supply (vsTLV2761ID)
- Rail-to-rail input and output operation (vsTLV2761ID)
Catatan Desain
Place a local bypass capacitor at the positive supply pin and return it directly to the supply or ground reference through a short path. Keep the shutdown control in a defined state during startup so the amplifier does not enter an unintended shutdown condition. Because the typical operating supply current is approximately 20 µA, capacitor leakage and input bias current can become significant in high-impedance designs. Select low-leakage capacitors and verify that the sensor, protection network, and feedback components do not consume more current than the signal chain requires.
Do not treat an 8-pin SOIC footprint as proof of functional drop-in compatibility. Before substituting the TLV2761ID, compare the shutdown-control polarity, shutdown timing, input bias current, output swing, and stability behavior against the original circuit. Also verify the maximum recommended supply voltage of 3.6 V. A mechanically similar amplifier can reverse the shutdown state or fail to meet the required bias and offset performance even when its headline bandwidth rating appears suitable.
Route the non-inverting input directly to the signal source and keep the inverting feedback path short to reduce parasitic coupling and oscillation risk. Place the shutdown trace away from high-slew-rate clock and switching-node traces, and provide a defined pull state if the controlling signal can float. For high-impedance sensors, use a guarded input or small-area routing to reduce leakage and surface contamination. Review the final layout for supply bypassing, output-load stability, and exposed pad or ground requirements specified by the manufacturer package drawing.
The 500 kHz gain-bandwidth product is sufficient for many general-purpose signal-conditioning tasks, but closed-loop bandwidth depends on the selected noise gain and the amplifier's stability behavior. Check the required settling time at the signal frequency and the bandwidth needed to suppress out-of-band noise. Avoid driving large capacitive loads without confirming stability from the manufacturer data. If the application requires a wider closed-loop bandwidth or lower offset than the TLV2760ID provides, select a different amplifier rather than compensating through excessive gain.
Informasi Konformitas
The available product information identifies the TLV2760ID as an industrial-temperature Texas Instruments amplifier but does not explicitly state the requested environmental or automotive compliance statuses. The -40°C to +85°C rating is not evidence of AEC-Q100 qualification.