TLV2770CP - 5.1MHz R-R Op Amp | Texas Instruments
MPN: TLV2770CP ✓ AktifTLV2770CP Ringkasan
An operational amplifier is a voltage-controlled differential amplifier used to amplify, buffer, filter, or compare small signals. The TLV2770 belongs to the general-purpose amplifier family within the broader signal-chain and analog IC hierarchy. Its rail-to-rail output allows the output voltage to approach the supply rails under suitable load conditions, while its shutdown input provides a direct means of reducing supply current when the signal path is not required.
The 5.1 MHz gain-bandwidth product supports closed-loop operation over a broad range of signal frequencies, while the 10.5 V/µs slew rate improves large-signal response. A maximum supply voltage of 5.5 V positions the device for low-voltage analog systems. The shutdown function is valuable in portable and embedded equipment because it can disable the amplifier during inactive periods and reduce system power consumption.
The TLV2770CP is specified for operation from a 2.7 V minimum supply, with a family maximum of 5.5 V. The single-amplifier configuration and 8-pin PDIP format simplify prototyping where a through-hole package is preferred. Because bipolar-style signal paths can behave differently near the supply rails, system-level settling and output swing should be evaluated at the actual supply voltage, load, and signal amplitude used in the finished circuit.
Typical applications include low-level sensor conditioning, analog instrumentation, active filters, data-conversion front ends, buffer stages, and industrial process-control modules. The 5.1 MHz bandwidth is particularly useful when the circuit must process signals above the kilohertz range, while the 10.5 V/µs slew rate helps preserve fidelity on rapidly changing waveforms. Shutdown can be used to disable unused analog channels between measurement events.
When implementing the device, place input and output decoupling capacitors close to the corresponding pins and keep feedback traces short to minimize noise pickup and parasitic capacitance. Do not assume that the output can reach either supply rail under every load condition; verify the output-voltage limits and load capability in the manufacturer datasheet for the chosen voltage and temperature.
This page combines the device's electrical characteristics, package information, drop-in replacement guidance, application guidance, and engineering design notes. It also distinguishes true pin-compatible options from functionally similar amplifiers whose shutdown-pin arrangements differ, helping designers make package-compatible design decisions without assuming that similar specifications guarantee interchangeability.
Pilihan pengganti yang segera untuk TLV2770CP — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera TLV2770CP (sama faktor bentuk dan kaki) — berbeza dalam Amplifier Type.
TLV2770IP
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →TLV2770AIP
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TLV2770CP Penilaian maksimum & Ciri-ciri Elektrik
| Amplifier Type | Single operational amplifier with shutdown |
| Number of Channels | 1 channel |
| Supply Voltage Minimum | 2.7 V |
| Supply Voltage Maximum | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz |
| Slew Rate | 10.5 V/µs |
| Output Topology | Rail-to-rail output |
| Gambaran Suhu Operasi | -40°C to +125°C |
| Kemasan | 8-pin PDIP |
| Jenis Pemasangan | Through-hole |
| Shutdown Control | Yes |
| Status RoHS | Unknown |
| REACH Status | Unknown |
Konfigurasi Pin TLV2770CP
| Pin 1 | OUT — Amplifier output |
| Pin 2 | V- — Negative supply connection |
| Pin 3 | IN+ — Non-inverting input |
| Pin 4 | IN- — Inverting input |
| Pin 5 | V+ — Positive supply connection |
| Pin 6 | NC — Not connected per datasheet |
| Pin 7 | NC — Not connected per datasheet |
| Pin 8 | SHDN — Shutdown control input |
Aplikasi Biasa
TLV2770CP patut untuk 6 aplikasis: Industrial Sensor Signal Conditioning, Precision Data Acquisition Front End, Active Analog Filters, Low-Voltage Process Control, Test and Measurement Buffer, Battery-Powered Portable Equipment.
Industrial Sensor Signal Conditioning
The TLV2770CP fits low-level industrial sensor front ends that require faster signal response than a conventional precision amplifier. Its 5.1 MHz gain-bandwidth product provides bandwidth for amplified sensor signals, while the 10.5 V/µs slew rate supports waveforms that change rapidly during transient events. Place the device in a non-inverting or differential conditioning stage with short feedback paths and local supply bypassing. The shutdown input can disable the channel between measurement cycles, reducing power demand when the sensor or converter is inactive.
Disebarkan
Precision Data Acquisition Front End
The TLV2770CP can drive the input stage of a data-acquisition system that benefits from a 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate. It is useful as a unity-gain buffer or moderate-gain amplifier ahead of an ADC, provided the required settling interval, noise, and output-range requirements are met. Keep the amplifier close to the ADC and use short traces to avoid adding parasitic capacitance between the analog node and converter input. Verify ADC acquisition timing against the amplifier's specified settling behavior.
Disebarkan
Active Analog Filters
The TLV2770CP is appropriate for active-filter stages operating from low-voltage analog rails where wider bandwidth and faster edge response improve signal throughput. Its 5.1 MHz gain-bandwidth product permits higher closed-loop gain than a precision, low-bandwidth amplifier, while the 10.5 V/µs slew rate helps preserve square-wave and transient content. Select resistor and capacitor values with the actual supply voltage and closed-loop gain in mind. Confirm output swing, stability, and component tolerances before extending filter order or increasing gain.
Disebarkan
Low-Voltage Process Control
The TLV2770CP can amplify control-loop signals in a 2.7 V to 5.5 V industrial or embedded control module. Its rail-to-rail output supports systems operating close to the available supply range, while the single-channel 8-pin PDIP package simplifies through-hole prototyping. The shutdown control is useful when a measurement channel is enabled only during a control cycle. Use the amplifier within its specified common-mode and output-swing limits, and design the surrounding filter network to prevent high-frequency switching noise from reaching the control node.
Disebarkan
Test and Measurement Buffer
The TLV2770CP is useful as an input or output buffer in compact test and measurement equipment that needs a 5.1 MHz bandwidth and 10.5 V/µs slew rate. Buffering can isolate the source from subsequent filter and conversion stages, while the shutdown function can reduce consumption when a measurement channel is idle. For high-accuracy measurements, verify input offset, bias-current, noise, and settling specifications at the required operating temperature. Maintain short, shielded analog traces and provide local bypass capacitance to reduce coupling from digital and switching circuitry.
Disebarkan
Battery-Powered Portable Equipment
The TLV2770CP suits portable analog equipment powered from a 2.7 V to 5.5 V rail because the family includes a shutdown function and operates from a low minimum supply voltage. The shutdown input can disable the amplifier during standby intervals, while the 5.1 MHz bandwidth handles signals beyond a basic precision-buffer application. Account for shutdown-state loading, input protection, and leakage from external resistors, all of which can dominate battery life. Evaluate the complete power budget and ensure that any disabled input remains within the device's input limits.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TLV2770CP — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TLV2770IP | TLV2770AIP |
|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 1 channel | 1 channel | 1 channel |
| Supply Voltage Maximum | 5.5 V | 5.5 V | 5.5 V |
| Gain-Bandwidth Product | 5.1 MHz | 5.1 MHz | 5.1 MHz |
| Slew Rate | 10.5 V/µs | 10.5 V/µs | 10.5 V/µs |
| Output Topology | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Shutdown Control | Yes | Yes | Yes |
| Operating Temperature Range | -40°C to +125°C | -40°C to +125°C | -40°C to +125°C |
| Pin and Functional Compatibility | TLV2770CP reference configuration | Consistent terminals, package, and functional characteristics | Consistent terminals, package, and functional characteristics |
Penyeberangsung Jelas
- High slew rate for a low-voltage single amplifier (vsTLV2770IP)
- 5.1 MHz bandwidth supports higher-frequency analog signals (vsTLV2770AIP)
- Pin-compatible shutdown-enabled configuration (vsOPA726)
Catatan Desain
Place the bypass capacitor as close as practical to the V+ and V- pins, and route the supply return directly to the ground reference used by the signal source and load. Keep the OUT, IN+, and IN- traces short, particularly around high-gain nodes. Long feedback runs can pick up interference and add parasitic capacitance that changes the effective gain or stability behavior.
Do not substitute an amplifier merely because its footprint matches. The OPA726 and TLV2770 have similar pinouts but different shutdown-pin arrangements, while the OPA725 and TLV2771 have no shutdown function. A mechanical fit is therefore insufficient. Check pin names, logic thresholds, supply range, common-mode limits, output swing, and stability before approving a replacement.
Use the 5.1 MHz gain-bandwidth product and 10.5 V/µs slew rate as design limits, not as a guarantee that every signal can be reproduced at full amplitude. Check output settling, load capacitance, and required gain-bandwidth allocation for the selected feedback network. In ADC front ends, include amplifier settling time in the overall acquisition interval and keep the analog trace away from switching nodes.
Treat the shutdown input as a controlled logic signal and ensure that it never exceeds the absolute maximum input limits. When the amplifier is disabled, confirm whether external feedback or bias networks can pull the output away from its shutdown state. If battery life is important, include the amplifier supply current, external-network current, and shutdown leakage in the complete system power calculation.
Maklumat Kesediaan
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was identified for this order code. Confirm environmental and automotive qualification requirements with Texas Instruments before qualification release.