TS374IDT - Low-Power Quad CMOS Comparator | STMicroelectronics
MPN: TS374IDT ✓ AktifTS374IDT Ringkasan
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when their relationship crosses a defined threshold. The TS374 belongs to the comparator hierarchy within analog and interface semiconductors. Its four-channel architecture allows one package to monitor four independent signals, reducing board area when several sensing or control functions are required.
The TS374IDT features very low supply current of approximately 0.1 mA per comparator, independent of supply voltage, and extremely low input bias and input offset currents of approximately 1 pA typical. The input offset voltage is specified to a maximum of 12 mV, while the response time reaches 600 ns. Its CMOS input stage supports operation from a single supply or from positive and negative dual supplies.
Each channel uses open-drain output structure, allowing the output to be pulled up to a suitable external voltage and permitting wired connection to a shared bus when only one channel should actively assert a logic state. The open-drain architecture also provides flexibility when interfacing with CMOS, MOS, or TTL-compatible downstream circuitry. The manufacturer lists the TS374 family as a low-power quad CMOS voltage comparator supporting supply ranges from 3 V to 16 V or ±1.5 V to ±8 V.
Typical uses include battery-powered threshold detection, industrial sensor interfaces, window or level monitoring, overvoltage detection, control systems, and general-purpose signal conditioning. The low input current is especially useful with high-impedance sensors because it minimizes loading of the measured signal.
Designers should account for input common-mode limits, output pull-up requirements, input offset voltage, and the effect of supply noise on comparison accuracy. Every open-drain output needs an appropriate pull-up resistor unless it is intentionally connected to a shared wired-AND node. Decoupling close to the supply pins remains important even though the device itself consumes very little current.
This product page combines manufacturer electrical characteristics, package details, sourcing information, and application guidance. It also highlights the design trade-offs involved when using a quad open-drain comparator instead of single-channel or push-pull alternatives, helping engineers select the correct replacement without changing the PCB footprint.
Pilihan pengganti yang segera untuk TS374IDT — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera TS374IDT (sama faktor bentuk dan kaki) — berbeza dalam Comparator Type, Logic Compatibility, Response Time.
TS374ID
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →TS374IDT Penilaian maksimum & Ciri-ciri Elektrik
| Number of Comparator Channels | 4 channels |
| Comparator Type | Low-power quad CMOS voltage comparator |
| Single Supply Operating Range | 3 V to 16 V |
| Dual Supply Operating Range | +/-1.5 V to +/-8 V |
| Supply Current per Comparator | 0.1 mA typical |
| Input Bias Current | 1 pA typical |
| Input Offset Current | 1 pA typical |
| Maximum Input Offset Voltage | 12 mV |
| Response Time | 600 ns maximum |
| Jenis Output | Open-drain |
| Logic Compatibility | CMOS, MOS, and TTL-compatible |
| Kemasan | 14-pin SOIC |
| Package Pin Count | 14 pins |
| Jenis Pemasangan | Surface mount |
| RoHS Compliance | Unknown |
| REACH Compliance | Unknown |
Panduan Konfigurasi Pin TS374IDT 14 pins
Konfigurasi pin untuk TS374IDT (14 pins pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk TS374IDT.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TS374IDT patut untuk 6 aplikasis: Battery-Powered Threshold Detection, Industrial Sensor Interfacing, Power-Supply Overvoltage Detection, Logic Level and Window Monitoring, Motor and Actuator Control, Portable Test and Measurement Equipment.
Battery-Powered Threshold Detection
The TS374IDT suits portable systems that must compare several sensed voltages while maintaining low standby consumption. Its four comparator channels operate from a single supply between 3 V and 16 V, and each channel draws approximately 0.1 mA according to the STMicroelectronics TS374 datasheet. A pull-up resistor is required on every open-drain output. The 12 mV maximum input offset and 600 ns maximum response time are suitable for battery thresholds, pack monitoring, and charger-state detection where nanosecond-level propagation is unnecessary.
Disebarkan
Industrial Sensor Interfacing
The TS374IDT can condition outputs from high-impedance industrial sensors because its typical input bias current and input offset current are each 1 pA. Four channels provide flexible threshold comparisons for temperature, level, or pressure signals without requiring four separate packages. The device accepts single supplies from 3 V to 16 V or dual supplies from ±1.5 V to ±8 V, while its open-drain outputs can be pulled up to the voltage required by the downstream controller.
Disebarkan
Power-Supply Overvoltage Detection
The TS374IDT can implement multiple protection thresholds around regulated power rails. Its 3 V to 16 V single-supply capability covers common low-voltage systems, while the 600 ns maximum response time provides prompt fault signaling. The 12 mV maximum input offset voltage is relevant when defining narrow protection windows, so designers should account for resistor tolerance and input imbalance. Open-drain outputs allow fault signals from multiple channels to be combined where the system architecture supports wired-AND behavior.
Disebarkan
Logic Level and Window Monitoring
Four independent TS374IDT channels can monitor upper and lower limits of two signals, creating two window detectors without duplicating comparator packages. The very low typical input bias current of 1 pA minimizes disturbance of the monitored voltage, while open-drain outputs provide flexible logic interfacing. The device can run from dual supplies of ±1.5 V to ±8 V when the monitored signals include negative levels, or from a single 3 V to 16 V rail in unipolar systems.
Disebarkan
Motor and Actuator Control
The TS374IDT can compare position, limit, or feedback voltages used in industrial actuator-control systems. Its 600 ns maximum response time allows the comparator output to initiate a control transition quickly enough for many non-safety-critical loops, and the quad architecture consolidates several limit checks. Supply-current demand of approximately 0.1 mA per comparator is useful in distributed equipment. Output pull-up values should be selected to match the control-logic voltage and required rise time.
Disebarkan
Portable Test and Measurement Equipment
The TS374IDT is useful in handheld meters and test equipment that require several live threshold comparisons without excessive power use. Its four channels share one 14-pin SOIC package, and typical current consumption of 0.1 mA per comparator supports longer operating time between battery charges. The 1 pA typical input bias current reduces loading on probes and high-impedance dividers. Designers should verify the input common-mode range at the selected supply voltage and use suitable pull-up resistors for the open-drain outputs.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TS374IDT — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TS374ID |
|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC |
| Brand | STMicroelectronics | STMicroelectronics |
| Number of Channels | 4 channels | 4 channels |
| Comparator Technology | CMOS | CMOS |
| Single Supply Range | 3 V to 16 V | 3 V to 16 V |
| Dual Supply Range | +/-1.5 V to +/-8 V | +/-1.5 V to +/-8 V |
| Supply Current per Comparator | 0.1 mA typical | 0.1 mA typical |
| Maximum Input Offset Voltage | 12 mV | 12 mV |
| Response Time | 600 ns maximum | 600 ns maximum |
| Output Type | Open-drain | Open-drain |
| Lifecycle Status | Active | Obsolete |
Penyeberangsung Jelas
- Four independent comparisons in one package (vsLM2904PWR)
- Very low typical input bias current (vsTS374ID)
- Flexible single- and dual-supply operation (vsTS374ID)
- Lower typical supply demand per channel (vsLM2904PWR)
Catatan Desain
Place a local supply bypass capacitor close to the TS374IDT supply pins and route the return directly to the device ground. Although the typical supply demand is only 0.1 mA per comparator, long supply traces can couple switching noise into a high-impedance comparison. Keep the bypass loop compact, and check the comparator common-mode range throughout startup and shutdown rather than assuming it remains valid while the rail is collapsing.
Treat the four comparator channels as sensitive analog paths even though the device is digital-output oriented. Keep high-impedance input nets short, avoid routing them beside switching nodes, and connect the open-drain pull-ups close to the output pins. If multiple outputs share a wired-AND bus, use one pull-up sized for the aggregate sink current and ensure every connected output is compatible with the shared logic level.
Do not substitute a generic four-channel comparator without checking pin assignments, input common-mode limits, output polarity, and supply-current behavior. The TS374IDT uses open-drain outputs that require pull-up resistors, and its maximum input offset voltage is 12 mV. For narrow threshold windows, include resistor tolerance and temperature effects in the error budget rather than relying solely on the nominal offset specification.
Maklumat Kesediaan
The component data does not provide a definitive RoHS, REACH, automotive-qualification, lead-free, halogen-free, or conflict-minerals declaration.