TS3L110D - 4-Channel 10/100 LAN Switch | Texas Instruments
MPN: TS3L110D ✓ AktifTS3L110D Ringkasan
An Ethernet LAN switch is an interface integrated circuit that routes differential signals between a transceiver or controller and multiple physical network connections. The TS3L110D belongs to the broader networking-switch hierarchy: four-channel LAN switch, special-purpose interface IC, and semiconductor. Its 2:1 multiplexer arrangement allows one differential signal pair to be connected to either of two alternatives, reducing the number of external routing components required in compact Ethernet equipment.
The TS3L110D supports four independently controlled 10/100 Base-T channels, with each channel implemented as an SPDT selector. Its 3 V to 3.6 V supply range is suited to 3.3 V systems, while the 8 ohm on-resistance provides a defined insertion-loss contribution at Ethernet signal rates. A low supply current of approximately 700 uA is useful in power-constrained network-access equipment. The 16-pin SOIC package supports conventional surface-mount assembly and inspection.
The device multiplexes eight differential inputs to four output channels. This arrangement is appropriate when an Ethernet controller, media-access controller, or PHY interface needs selectable access to more than one physical channel. Because it is a switching device rather than an active repeater or transceiver, the TS3L110D does not itself establish the physical-layer link. It selects existing differential signals and must be paired with suitable 10/100 Ethernet PHYs, magnetics, connectors, and network-control circuitry.
Typical uses include compact Ethernet switches, network interface controllers, industrial Ethernet equipment, embedded gateways, and set-top or communications products. The part can also be used in test systems where a controller must route differential pairs between instrumentation or PHY channels. Design choices should account for trace impedance, connector and magnetics layout, control timing, and the high-speed return path between the switch and its Ethernet PHY.
Use the manufacturer pin-description and typical-application diagrams when assigning control inputs and differential nets. Maintain controlled-impedance routing for Ethernet pairs, keep switch traces short, and place bypass capacitance close to the supply pin. Verify the exact enable polarity, control interface, and recommended resistor and capacitor values against the current manufacturer datasheet before releasing a PCB.
This page organizes the verified 3.3 V supply, SPDT configuration, four-channel architecture, 8 ohm on-resistance, approximately 700 uA supply current, 16-pin SOIC construction, application guidance, and qualified replacement options into an engineering-focused reference.
Pilihan pengganti yang segera untuk TS3L110D — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
TS3L110E4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TS3L110G4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TS3L110DG4
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
TS3L110D Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | 4-channel 10/100 Base-T LAN switch |
| Switch Configuration | 2:1 SPDT per channel |
| Number of Channels | 4 channels |
| Differential Signal Count | 8 differential channels to 4 channels |
| Nominal Supply Voltage | 3.3 V |
| Supply Voltage Range | 3 V to 3.6 V |
| On-Resistance | 8 ohm |
| Arus Pemberi Arus | 700 uA |
| Supported Network Class | 10/100 Base-T |
| Kemasan | 16-pin SOIC |
| Package Family | SOIC surface-mount package |
| Jenis Pemasangan | Surface Mount |
| Product Status | Active |
Panduan Konfigurasi Pin TS3L110D soic surface-mount package
Konfigurasi pin untuk TS3L110D (soic surface-mount package pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk TS3L110D.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
TS3L110D patut untuk 6 aplikasis: Compact Ethernet Network Interface, Industrial Ethernet Gateway, Network Interface Controller, Set-Top Communications Equipment, Ethernet Test and Measurement, Embedded Communications Gateway.
Compact Ethernet Network Interface
The TS3L110D is appropriate for a compact 10/100 network-access design that must route multiple differential pairs between an Ethernet PHY and selectable board-level connections. Its four 2:1 SPDT channels provide eight differential inputs mapped to four outputs, while the 3 V to 3.6 V operating range integrates directly with a 3.3 V Ethernet interface. The 16-pin SOIC package simplifies assembly compared with a discrete matrix of analog switches. Designers should preserve controlled-impedance routing, minimize return-path discontinuities, and verify switch insertion loss against the Ethernet interface budget before finalizing signal-integrity simulation.
Disebarkan
Industrial Ethernet Gateway
The TS3L110D can support selectable Ethernet paths in an industrial gateway that connects a controller, service interface, and external network equipment. Its four SPDT channels suit differential routing, and approximately 700 uA supply current is valuable in embedded equipment where the interface must remain available without adding substantial power load. A 3.3 V system can power the device directly when signal levels and control timing are compatible. For industrial deployment, validate temperature grade, isolation boundaries, surge protection, and grounding with the current manufacturer documentation rather than inferring those characteristics from the family name.
Disebarkan
Network Interface Controller
A network interface controller can use the TS3L110D when several 10/100 Base-T differential paths must be selected under digital control. Four independent 2:1 paths give the controller a way to reach multiple PHY-facing or board-level destinations while retaining one compact analog routing device. The 8 ohm on-resistance and 3.3 V supply characterize the component as a dedicated LAN-routing element rather than a generic communications transceiver. Firmware must control selection only after the connected PHY is in a safe state, and the PCB should keep switch and PHY differential traces short and impedance controlled.
Disebarkan
Set-Top Communications Equipment
The TS3L110D fits set-top and communications equipment requiring selectable 10/100 Ethernet differential paths in a constrained board area. Its four-channel multiplexed architecture reduces the component count compared with multiple discrete SPDT switches, and the 16-pin SOIC is compatible with standard surface-mount assembly. The approximately 700 uA operating current also supports power-conscious consumer networking designs. Engineers should place the device near the routed Ethernet pairs, maintain uninterrupted reference planes, and review the recommended bypass network and control levels in the manufacturer datasheet.
Disebarkan
Ethernet Test and Measurement
The TS3L110D can be used in test equipment to route 10/100 Base-T differential pairs between a test stimulus, analyzer, or device under test. Its eight differential inputs and four outputs provide a practical 2:1 selection matrix for repeatable connection management. Because the device does not act as a full Ethernet transceiver, instrumentation must include appropriate termination, magnetics, and control logic where required. Validate the 8 ohm on-resistance contribution, insertion loss, and control timing across the intended Ethernet frequencies, and document each switch state to support automated test sequencing.
Disebarkan
Embedded Communications Gateway
The TS3L110D is useful in embedded communications gateways that expose selectable 10/100 Ethernet paths to a host processor or communications module. Its four SPDT channels and 3.3 V operation fit a 3.3 V embedded power architecture, while the SOIC-16 format supports compact board layouts and automated inspection. The approximately 700 uA current can be advantageous in systems with limited thermal budgets. Implement power-on control sequencing so that the network PHY never drives an improperly selected path, and keep copper routing short to reduce sensitivity to board-level impedance discontinuities.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk TS3L110D — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | TS3L110E4 | TS3L110G4 | TS3L110DG4 |
|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | 4-channel 10/100 Base-T LAN switch | 4-circuit analog multiplexer / LAN switch | TS3L110 family device | TS3L110 family device |
| Switch Configuration | 2:1 SPDT | 2:1 SPDT | 2:1 SPDT | 2:1 SPDT |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Differential Signal Organization | 8 differential channels to 4 channels | 8 differential channels to 4 channels | 8 differential channels to 4 channels | 8 differential channels to 4 channels |
| Supply Voltage Range | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V |
| On-Resistance | 8 ohm | 8 ohm | 8 ohm | 8 ohm |
| Supply Current | 700 uA | 700 uA | 700 uA | 700 uA |
Penyeberangsung Jelas
- Dedicated four-channel 10/100 Base-T routing organization (vsTS3L110E4)
- Eight differential inputs consolidated onto four channels (vsTS3L110G4)
- Low 3.3 V operating current (vsTS3L110DG4)
Catatan Desain
Route all differential pairs as controlled-impedance nets with continuous reference planes and minimal stubs. Keep the TS3L110D close to the Ethernet PHY and connector paths, and avoid placing test pads or package transitions on a differential pair unless their effects are included in signal-integrity analysis. The stated 8 ohm on-resistance must be included in the end-to-end channel-loss budget along with PHY, magnetics, and connector losses.
Place the required input and output bypass capacitors close to the supply and ground pins, following the manufacturer recommended-application layout. Provide a low-impedance ground connection and avoid splitting the ground reference beneath the device. Use the 16-pin SOIC land pattern from the Texas Instruments package drawing, and inspect the assembled board for solder bridges because closely spaced pins can complicate optical inspection.
Do not treat the TS3L110D as a complete Ethernet transceiver: it routes existing differential signals but does not perform 10/100 Base-T line coding, clock recovery, or link training. Verify control polarity, inactive-state behavior, and power-on sequencing in the manufacturer pin table and truth table. Confirm that the selected PHY supports the switch's signal levels and that external magnetics and protection are placed according to the target Ethernet design.
Maklumat Kesediaan
No explicit compliance declarations or automotive qualification statements appear in the available manufacturer, distributor, or cross-reference results. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status using the current manufacturer product documentation or a project-specific supplier declaration.