XC4VSX25-10FF668I - 23,040-Cell Virtex-4 SX FPGA | AMD
MPN: XC4VSX25-10FF668I ✗ Akhir HayatXC4VSX25-10FF668I Ringkasan
A field-programmable gate array is a semiconductor whose digital logic, interconnect, and I/O behavior are configured after manufacture. Within the product hierarchy, an FPGA is a programmable logic device and a semiconductor. The Virtex-4 SX family combines configurable logic blocks with dedicated digital signal processing resources and substantial on-chip memory, allowing complete control systems to be implemented in a single device rather than across multiple fixed-function chips.
The XC4VSX25 combines 23,040 logic cells with 320 configurable logic blocks in a 668-ball FCBGA package. The 90 nm CMOS process and 1.2 V core voltage place it in a high-density programmable-logic class designed for embedded processing, serial connectivity, bus aggregation, and signal processing. Its -10 designation identifies the performance grade, while the -10FF668 package code specifies the 668-ball package configuration.
Technical adoption depends on validating power, clock, configuration, and interface requirements against the complete device documentation. The 1028 MHz figure should be treated as a device-specific internal-frequency value rather than a guarantee that every user I/O can operate at that rate. Practical designs must also account for the large number of power, ground, configuration, clock, and user-I/O balls in the FCBGA package.
Typical uses include telecom line-card processing, industrial control and automation, high-speed networking, server and storage interfaces, test and measurement equipment, and embedded DSP. The 23,040 logic cells make the device appropriate for parallel datapaths and protocol engines, while dedicated DSP resources allow arithmetic-heavy filtering and signal transformation without implementing every multiplier in general-purpose fabric.
The principal design challenge is high-speed PCB execution. A 668-ball FCBGA requires a dense, multilayer board with short return paths, carefully controlled impedance, multiple power planes, and disciplined decoupling. Configuration storage, clocking, JTAG access, and programming support also require complete schematic and layout review before production release.
This product page combines the verified device identity, package details, operating information, comparison guidance, and engineering-focused replacement considerations. It also highlights practical constraints that engineers must evaluate when moving from the XC4VSX25-10FF668I into a redesign, industrial temperature upgrade, or a different Virtex-4 SX density and speed grade.
Pilihan pengganti yang segera untuk XC4VSX25-10FF668I — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera XC4VSX25-10FF668I (sama faktor bentuk dan kaki) — berbeza dalam Package Type, Speed Grade, Mounting Type, Device Type, Internal Frequency.
XC4VSX25-11FF668I
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →XC4VSX25-10FFG668I
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
XC4VSX25-10FF668C
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →XC4VSX35-10FFG668I
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
XC4VSX35-10FF668C
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →XC4VSX25-10FF668I Penilaian maksimum & Ciri-ciri Elektrik
| Device Type | Virtex-4 SX field-programmable gate array |
| Logic Cells | 23,040 cells |
| Configurable Logic Blocks | 320 blocks |
| Logic Block Count | 2,560 blocks |
| Internal Frequency | 1028 MHz |
| Process Technology | 90 nm CMOS |
| Core Supply Voltage | 1.2 V |
| Gambaran Suhu Operasi | 0°C to 85°C |
| Package Type | 668-ball FCBGA |
| Total Pin Count | 668 pins |
| Terminal Pitch | 1.00 mm |
| Jenis Pemasangan | Surface mount |
| Speed Grade | -10 grade |
| Logic Family | CMOS programmable logic |
| Status RoHS | unknown |
| REACH Status | unknown |
| Automotive Qualification | Not qualified |
| Program Memory | 2,359,296 bits |
Panduan Konfigurasi Pin XC4VSX25-10FF668I 668-ball fcbga
Konfigurasi pin untuk XC4VSX25-10FF668I (668-ball fcbga pakai). IC digital ini termasuk GPIO, antaramuka komunikasi (UART, SPI, I2C), dan pin kuasa. Rujuk dokumen pengeluar untuk fungsi pin alternatif dan opsi konfigurasi. Biasa digunakan dalam rancangan sistem ter嵌入式 dan PCB.
Tiada data garisan pin yang diperoleh untuk XC4VSX25-10FF668I.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
XC4VSX25-10FF668I patut untuk 6 aplikasis: Telecom Line-Card Signal Processing, Industrial Control and Automation, High-Speed Network Interface Aggregation, Server and Storage Interface Control, Test and Measurement Instrumentation, Embedded DSP and Digital Filtering.
Telecom Line-Card Signal Processing
The XC4VSX25-10FF668I fits telecom line-card designs that combine parallel packet processing, serial interfaces, and dedicated arithmetic functions. Its 23,040 logic cells and 320 configurable logic blocks provide substantial capacity for protocol state machines, buffering, framing, and control logic, while the listed 1028 MHz internal frequency supports demanding clock domains. The -10 speed grade and 1.2 V CMOS core should be evaluated against the complete timing specification. A 668-ball FCBGA also demands a multilayer PCB with stringent power delivery and return-path control, making careful pin assignment, layer transitions, and decoupling essential for reliable telecom equipment.
Disebarkan
Industrial Control and Automation
The XC4VSX25-10FF668I can implement industrial controllers that require deterministic parallel logic, multiple I/O standards, and flexible hardware configuration. Its 23,040 logic cells allow control algorithms, communication stacks, motion sequencing, and diagnostics to be consolidated in one FPGA rather than divided among multiple processors. The device is documented for 0°C to 85°C operation, making it suitable for many industrial enclosures when the complete system thermal profile remains inside that range. Designers should reserve resources for fault handling and safe-state behavior, then validate signal integrity and power integrity across every supported voltage and temperature condition.
Disebarkan
High-Speed Network Interface Aggregation
The XC4VSX25-10FF668I is suitable for network interface aggregation, packet classification, and protocol adaptation because it provides 23,040 logic cells, 320 configurable logic blocks, and a listed 1028 MHz internal-frequency figure. These resources can support parallel datapaths, look-up structures, FIFO control, and framing logic while leaving dedicated fabric for high-speed serial interfaces. The actual line rate remains dependent on the selected I/O standard, board topology, and timing closure, so the 1028 MHz figure should not be treated as a universal I/O-rate guarantee. Pin planning should preserve complete reference-clock and decoupling access on the 668-ball FCBGA.
Disebarkan
Server and Storage Interface Control
The XC4VSX25-10FF668I can serve as a dedicated interface controller in server, storage, and accelerator systems where flexible logic timing and multiple external interfaces are important. Its 23,040 logic cells and 320 configurable logic blocks support command sequencing, DMA control, data routing, error handling, and status generation. The device's listed 1.2 V core voltage requires a carefully partitioned power tree, while the 668-ball FCBGA requires short high-speed escape paths and a multilayer stack-up. Clock jitter, power sequencing, termination, and simultaneous-switching-noise analysis should be completed before the design is released for volume production.
Disebarkan
Test and Measurement Instrumentation
The XC4VSX25-10FF668I fits programmable test and measurement equipment that combines acquisition logic, sequencing, timing control, and data processing in one FPGA. Its 23,040 logic cells support parallel capture pipelines, trigger logic, counters, and control functions, while the listed internal frequency of 1028 MHz provides headroom for deeply pipelined processing. Instrument-grade accuracy still depends on calibrated references, controlled clock distribution, and carefully isolated analog interfaces. Because the FCBGA has 668 balls at 1.00 mm pitch, PCB warpage, thermal cycling, component placement, and accessible power planes must be validated during hardware bring-up.
Disebarkan
Embedded DSP and Digital Filtering
The XC4VSX25-10FF668I is well suited to fixed and floating-point digital signal processing because the Virtex-4 SX family combines programmable fabric with dedicated DSP-oriented resources. The device's 23,040 logic cells can support control paths, buffer management, and multi-channel scheduling around the arithmetic blocks, allowing filters, correlators, and data-classification engines to be consolidated. The listed 1028 MHz internal-frequency value must be reconciled with the selected clocking, pipeline depth, DSP operating conditions, and I/O timing budget. In a 668-ball FCBGA implementation, controlled-clock routing and uninterrupted power planes are particularly important because DSP-heavy designs can concentrate switching activity in small regions.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk XC4VSX25-10FF668I — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | XC4VSX25-11FF668I | XC4VSX25-10FFG668I | XC4VSX25-10FF668C | XC4VSX35-10FFG668I | XC4VSX35-10FF668C |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | 668-ball FCBGA | 668-ball FCBGA | 668-ball FCBGA | 668-ball FCBGA | 668-ball FCBGA | 668-ball FCBGA |
| FPGA Family | Virtex-4 SX | Virtex-4 SX | Virtex-4 SX | Virtex-4 SX | Virtex-4 SX | Virtex-4 SX |
| Speed Grade | -10 | -11 | -10 | -10 | -10 | -10 |
Penyeberangsung Jelas
- Exact -10 speed-grade identity (vsXC4VSX25-11FF668I)
- Original non-G ordering identity (vsXC4VSX25-10FFG668I)
- Lower density than the VSX35 alternatives (vsXC4VSX35-10FF668C)
Catatan Desain
Plan the PCB for a 668-ball FCBGA with a 1.00 mm terminal pitch rather than treating it as a conventional fine-pitch BGA. Assign power and ground balls directly to corresponding plane layers, keep configuration and clock pins away from high-slew-rate user outputs, and provide uninterrupted return paths beneath every high-speed route. Validate layer transitions, via construction, backdrilling, and package warpage using the manufacturer package and design rules.
Separate the 1.2 V core rail from the other supply requirements and validate sequencing, tolerance, transient response, and startup behavior against the device documentation. Place local ceramic decoupling close to the associated power balls and use the package power-plane pattern to minimize distribution impedance. Estimated dissipation for a finished design should be calculated from actual core and I/O voltage, current, and duty cycle before copper and thermal solutions are finalized.
Use the manufacturer package files to generate the symbol, footprint, and escape routing. Keep the configuration interface accessible for programming and boundary-scan operations, provide clean clock reference routing, and reserve unused balls according to the package guidance. Do not infer a pinout from the 668-ball count: power, ground, configuration, clock, and user-I/O assignments must come from the exact device package data.
Do not assume that every alternative with the same package family is a functional drop-in. The -10 and -11 speed grades can change timing margins and power behavior, the G suffix identifies a lead-free ordering option, and the C suffix requires confirmation of qualification and temperature coverage. Validate the ordering guide, pin assignments, electrical limits, configuration method, and design-tool support before substituting any listed alternative.
Maklumat Kesediaan
The XC4VSX25-10FFG668I listing is identified as Pb-Free, but explicit compliance documentation for the target XC4VSX25-10FF668I was not identified. Automotive qualification is not indicated for the target ordering code.