A3P060-FG144T - 60K-Gate Automotive ProASIC3 FPGA | Microchip
MPN: A3P060-FG144T ✓ ActiveA3P060-FG144T Overview
A field-programmable gate array is a programmable digital semiconductor that combines configurable logic fabric, programmable interconnect, and input/output blocks. Within the broader semiconductor hierarchy, the A3P060-FG144T belongs to the FPGA and CPLD class, while ProASIC3 is a flash-based FPGA family. Flash configuration retains the programmed circuit after power removal, reducing external boot-memory requirements compared with SRAM-only FPGA architectures.
The device provides 1,536 configurable logic blocks, approximately 18,432 flip-flop or latch positions, and 96 user I/O according to the ProASIC3 family information. It supports a 1.5 V core operating condition for systems designed around 1.5-V-only power rails. Its 231 MHz performance figure makes it appropriate for control logic, interface bridging, automotive body electronics, sensor aggregation, and general-purpose embedded logic rather than computationally intensive signal processing.
The automotive-oriented part designation identifies the A3P060-FG144T within the Automotive ProASIC3 Flash Family FPGAs. Automotive qualification documentation and product-selection material should be consulted when the application requires AEC-Q100 status, PPAP documentation, or production-part approval. The family documentation also identifies low-impedance flash switches and a core tile that can implement either a three-input lookup-table function or a D flip-flop or latch with enable control.
Typical uses include vehicle body-control modules, sensor interfaces, actuator controllers, gateway logic, panel electronics, and industrial control equipment. The 96-I/O count provides substantial connectivity for mixed digital interfaces, while 60K-gate density supports concurrent state machines, communication protocols, data acquisition, and supervisory logic in one device.
Designers should preserve the package-specific footprint, ball assignment, power architecture, and programming configuration during any migration. Use the pin-description and package tables in the manufacturer datasheet when assigning PCB balls. A 1.5 V core rail requires suitable decoupling and sequencing, and the flash configuration architecture requires the correct programming algorithm and device-specific toolchain.
This page combines the verified A3P060-FG144T family specifications, package identification, sourcing links, same-footprint alternatives, and practical migration guidance. It is intended to help engineers quickly distinguish exact automotive ordering codes, assess pin-compatible options, and plan PCB, programming, power, and qualification reviews before committing a design to production.
Drop-in alternatives for A3P060-FG144T — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with A3P060-FG144T (same form factor and footprint) — differing in Device Type, Package, Process Technology, User I/O Count.
A3P060-FG144I
✅ Drop-InContact for price
View Datasheet →A3P060-TQG144I
✅ Drop-In📋 Reference alternative (not in catalog)
A3P060-FGG144I
✅ Drop-In📋 Reference alternative (not in catalog)
A3P060-FG144T Maximum Ratings & Electrical Characteristics
| Device Type | Automotive ProASIC3 Flash FPGA |
| Logic Density | Approximately 60,000 gates |
| Configurable Logic Blocks | 1,536 CLBs |
| Flip-Flop or Latch Positions | 18,432 positions |
| Maximum Frequency | 231 MHz |
| User I/O Count | 96 I/O |
| Core Voltage | 1.5 V |
| Process Technology | 130 nm |
| Configuration Memory | Flash |
| Package | 144-LBGA |
| Mounting Type | Surface Mount |
| Programmable Logic Type | FPGA |
| Core Tile Function | Three-input LUT equivalent or D flip-flop/latch with enable |
| RoHS Status | Non-Compliant |
| Lead-Free Status | Contains Lead |
A3P060-FG144T 144-lbga Pin Configuration Guide
Pin configuration for A3P060-FG144T (144-lbga package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for A3P060-FG144T.
Refer to the datasheet for full pin configuration.
Typical Applications
A3P060-FG144T is suitable for 6 applications: Automotive Body Control Module, Vehicle Sensor Aggregation, Actuator and Motor Control, Automotive Gateway and Interface Bridging, Industrial Control and Data Acquisition, Security and Diagnostics Controller.
Automotive Body Control Module
The A3P060-FG144T fits centralized vehicle body-control logic because its 1,536 CLBs and 18,432 flip-flop or latch positions can host multiple state machines, timers, debounce logic, and interface protocols. The 96-I/O count provides broad connectivity for switches, lamps, door modules, and diagnostic links within one package. Its automotive ProASIC3 positioning supports development of body systems requiring nonvolatile flash configuration. Engineers should allocate the device's 1.5 V core budget, match I/O levels to vehicle signals, and use the manufacturer package and automotive qualification documents before production release.
Recommended
Vehicle Sensor Aggregation
The A3P060-FG144T can consolidate inputs from multiple automotive sensors into a common control layer. Its 96 I/O and approximately 60,000 gates provide sufficient parallelism for signal conditioning, thresholding, filtering state, diagnostics, and communication framing. Flash configuration allows the aggregation logic to remain configured after power removal, which is useful in standby or intermittent supply systems. A robust implementation should isolate incompatible sensor domains, apply appropriate input conditioning, and verify that every I/O standard and voltage domain is supported by the selected package and ordering grade.
Recommended
Actuator and Motor Control
The A3P060-FG144T is suitable for coordinating solenoids, relays, motors, and discrete actuators where deterministic control logic must interface with external driver circuits. Its 1.5 V core and 231 MHz class performance support supervisory sequencing, fault handling, pulse timing, and closed-loop state management, while the 96 I/O allow multiple actuator channels to share one controller. Designers should keep high-current switching outside the FPGA, provide suitable isolation and protection, account for inductive transients, and validate timing against the external power stage rather than relying only on the FPGA clock specification.
Recommended
Automotive Gateway and Interface Bridging
The A3P060-FG144T can bridge dissimilar vehicle communication interfaces by implementing protocol conversion, framing, filtering, and diagnostic routing in programmable logic. With 1,536 CLBs, 18,432 register positions, and 96 I/O, the device can handle multiple concurrent channels without relying on a fixed-function microcontroller protocol engine. Design work should include verified clock-domain relationships, bus impedance requirements, timeout behavior, fault containment, and pin-level I/O compatibility. Programming the flash configuration and validating it under reset and power-cycle conditions are essential production checks.
Recommended
Industrial Control and Data Acquisition
The A3P060-FG144T can implement deterministic acquisition, sequencing, and supervisory control for industrial equipment with parallel sensors, counters, interlocks, and communication peripherals. The 60K-gate density and 96 I/O provide enough parallel resources for multi-channel acquisition, while the 1.5 V core simplifies integration with modern low-voltage logic. The flash-based configuration supports rapid field updates and retention through power interruption. For dependable operation, separate analog conditioning from the FPGA, protect inputs against industrial transients, and confirm timing margins with the external sensor and actuator timing specifications.
Recommended
Security and Diagnostics Controller
The A3P060-FG144T can serve as a programmable security, authentication, and diagnostics controller in an embedded platform. Its flash configuration permits complex state machines, challenge-response logic, key-related data handling, event logging, and fault reporting to be implemented in parallel hardware. The 96 I/O supports communication channels and status inputs, while 1,536 CLBs provide deterministic logic capacity. Security designs should add measures beyond simple bitstream confidentiality, including controlled programming access, rollback protection where supported, startup validation, tamper monitoring, and documented key-handling procedures.
Recommended
Recommended Products Summary
Engineering reference data for A3P060-FG144T — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | A3P060-FG144I | A3P060-TQG144I | A3P060-FGG144I |
|---|---|---|---|---|
| Package | 144-LBGA | 144-LBGA | 144-pin FBGA | 144-pin FBGA |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| FPGA Family | Automotive ProASIC3 Flash | ProASIC3 Flash | ProASIC3 | ProASIC3 |
| Logic Density | Approximately 60,000 gates | 60,000 gates | 60,000 gates | 60,000 gates |
| Configurable Logic Blocks | 1,536 CLBs | 1,536 CLBs | 1,536 CLBs | 1,536 CLBs |
| Maximum Frequency | 231 MHz | 231 MHz | 231 MHz | 231 MHz |
| User I/O | 96 I/O | 96 I/O | 96 I/O | 96 I/O |
| Core Voltage | 1.5 V | 1.5 V | 1.5 V | 1.5 V |
| Process Technology | 130 nm | 130 nm | 130 nm | 130 nm |
| Ordering Grade | Automotive FG144T code | FG144I ordering code | TQG144I ordering code | FGG144I ordering code |
Key Differentiators
- Automotive-specific ordering designation (vs A3P060-FG144I)
- Substantial logic and I/O integration in one 144-LBGA device (vs A3P060-TQG144I)
- Nonvolatile flash configuration (vs A3P060-FGG144I)
- Low-voltage 1.5 V core integration (vs A3P060-FG144I)
Design Notes
The A3P060-FG144T operates from a 1.5 V core and may require additional I/O or configuration rails defined by the family datasheet. Place the required decoupling capacitors at their associated supply balls, keep high-current return paths compact, and separate sensitive core routing from switching-node return currents. Verify absolute maximum limits, startup sequencing, and I/O voltage compatibility before finalizing the power tree.
Do not derive the 144-LBGA land pattern from the generic package name alone. Use the Microchip package drawing and pin table for the exact ordering code, including ball-map differences and exposed or thermal requirements. Preserve all power, ground, configuration, clock, and JTAG balls, and route each interface to the ball assigned by the datasheet rather than relying on a family-level pinout assumption.
The closest documented alternatives differ mainly by ordering suffix, grade, or qualification. Before substitution, compare the exact temperature range, automotive qualification, speed grade, flash configuration method, production status, and package drawing. A matching 144-pin count does not by itself prove that programming files, I/O behavior, and operating limits are interchangeable.
Use a continuous ground reference beneath the BGA and minimize loop area for every clock, configuration, and serial interface. Respect simultaneous-switching-noise limits when assigning high-speed outputs, and maintain clear return paths beneath signal rows. Check the package drawing for thermal-array connections, then evaluate board copper, via placement, and enclosure heat dissipation against the required automotive ambient and junction-temperature conditions.
Compliance Information
The A3P060-FG144T is identified in the Automotive ProASIC3 Flash Family FPGAs documentation. The available part listing reports RoHS Non-Compliant and Contains Lead. Confirm AEC-Q100 grade, PPAP documentation, and production approval against the exact ordering code and customer program.