AD8018ARZ - Dual 5V High-Speed xDSL Amplifier | ADI
MPN: AD8018ARZ ✓ ActiveAD8018ARZ Overview
An xDSL line-driver amplifier is a specialized operational-amplifier stage used at the transmitter side of a digital subscriber-line system. It combines high bandwidth and fast slew rate with the ability to drive signals close to the supply rail. In the broader electronics hierarchy, the AD8018 is an operational amplifier, a high-speed amplifier, an analog IC, and ultimately a semiconductor for line-interface signal conditioning.
The AD8018ARZ combines a 5 V single-supply architecture with low-distortion output capability. Its 300 V/µs slew rate supports rapid transitions in modulated xDSL signals, while the 54 dB common-mode rejection ratio reduces sensitivity to unwanted differential-mode interference. The dual-channel configuration permits two driver functions in one package, helping reduce board area in customer-premises equipment with parallel signal paths.
The AD8018 uses a current-feedback operational-amplifier architecture suited to high-speed, low-distortion line-driving tasks. The manufacturer describes the output stage as capable of driving low-distortion signals to within 0.5 V of the supply rail, making output swing and load capability important design considerations. Because it is intended for a 5 V single supply, input and output common-mode ranges must be checked against the actual line-driver circuit rather than assumed from general-purpose op-amp behavior.
Typical applications include ADSL line interfaces, PCMCIA and PCI-based customer-premises equipment, USB-related line drivers, and other high-speed communications paths. The dual amplifier is particularly useful where two related transmit channels must be placed close together and operate from the same supply. Termination, output-current, and signal-integrity requirements remain application-specific and should be validated against the relevant xDSL line interface and transmission standard.
PCB design should minimize trace length between the amplifier and the line-driver network, maintain a continuous ground return, and decouple the 5 V supply locally. High-speed output edges make short return paths and careful control of parasitic inductance important. The output network, line impedance, and cable length can materially affect distortion and reach, so simulation with the actual transformer, transformerless network, and termination is recommended.
This page combines the manufacturer product information with package details, practical circuit-placement guidance, qualified same-package alternatives, and a parameter comparison for engineers evaluating the AD8018ARZ in 5 V xDSL line-drive designs.
Drop-in alternatives for AD8018ARZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with AD8018ARZ (same form factor and footprint) — differing in Product Type, Package, Amplifier Type, Primary Application, Slew Rate.
AD8014ARZ
✅ Drop-InContact for price
View Datasheet →THS3201D
✅ Drop-InContact for price
View Datasheet →MAX4107
✅ Drop-In📋 Reference alternative (not in catalog)
LMH6702
✅ Drop-In📋 Reference alternative (not in catalog)
AD8018ARZ Maximum Ratings & Electrical Characteristics
| Amplifier Type | Dual high-speed current-feedback operational amplifier |
| Number of Channels | 2 channels |
| Supply Voltage | 5 V |
| Slew Rate | 300 V/µs |
| Common-Mode Rejection Ratio | 54 dB |
| Operating Temperature | -40°C to +85°C |
| Package | 8-pin SOIC |
| Number of Pins | 8 pins |
| Mounting Type | Surface mount |
| Output Swing Limit | Within 0.5 V of the supply rail |
| Signal Type | xDSL line-drive signals |
| Primary Application | xDSL customer-premises equipment |
| Nominal Supply Configuration | Single supply |
AD8018ARZ Pin Configuration
| Pin 1 | OUTA — Amplifier A output |
| Pin 2 | INA− — Inverting input for amplifier A |
| Pin 3 | INA+ — Noninverting input for amplifier A |
| Pin 4 | V− — Negative supply connection |
| Pin 5 | INB+ — Noninverting input for amplifier B |
| Pin 6 | INB− — Inverting input for amplifier B |
| Pin 7 | OUTB — Amplifier B output |
| Pin 8 | V+ — Positive supply connection |
Typical Applications
AD8018ARZ is suitable for 6 applications: ADSL Line-Driver Interface, USB-Based CPE Line Interface, PCMCIA Modem Interface, PCI-Based Customer Premises Equipment, Dual-Channel High-Speed Signal Conditioning, Low-Cost CPE Transmitter Card.
ADSL Line-Driver Interface
The AD8018ARZ fits an ADSL transmitter because it combines two high-speed amplifier channels with a 300 V/µs slew rate in an 8-pin SOIC. It is intended for single-supply xDSL systems and can drive low-distortion signals to within 0.5 V of the 5 V rail. Place the amplifier close to the transformer or line-network termination to minimize trace-area effects. Validate distortion and output swing with the actual winding ratio, load, and line length because those external factors determine the final eye and spectral performance.
Recommended
USB-Based CPE Line Interface
The AD8018ARZ is suitable for USB-based customer-premises equipment where a compact dual-channel transmitter must operate from 5 V. Its two channels can support parallel line-drive functions without using two separate packages, while the 300 V/µs slew rate provides the speed required for fast digital transitions. The PCB layout should keep the output path short and provide a low-impedance ground return. Confirm that the selected USB line-driver topology stays inside the amplifier's input and output operating ranges.
Recommended
PCMCIA Modem Interface
The AD8018ARZ was designed with PCMCIA-based customer-premises equipment in mind, making it appropriate for dual xDSL transmit stages in compact modem hardware. Its 8-pin SOIC package limits board area, and the dual topology allows matched channel placement. Because PCMCIA and related modem assemblies often operate close to digital switching circuitry, use local supply bypassing and a continuous ground plane. Simulate the complete line network to verify distortion rather than relying only on the amplifier's 54 dB CMRR figure.
Recommended
PCI-Based Customer Premises Equipment
The AD8018ARZ supports PCI-based customer-premises equipment by providing two high-speed line-drive amplifiers for a 5 V transmitter section. Its low-cost dual SOIC implementation is appropriate where board area and component count matter, and its high slew rate helps reproduce rapid line transitions. Route outputs directly toward the isolation or termination network, avoiding long stubs through the PCB. Check the output-voltage margin and distortion against the exact external network before production release.
Recommended
Dual-Channel High-Speed Signal Conditioning
The AD8018ARZ can condition two related high-speed signals when the system uses a 5 V single supply and needs compact dual-channel circuitry. Its 300 V/µs slew rate makes it appropriate for edges substantially faster than those handled by many general-purpose operational amplifiers. Match both channels carefully and provide symmetrical routing where timing alignment matters. Use the pinout table in the manufacturer datasheet for assignments, and verify stability with the actual capacitive and resistive loads connected to each output.
Recommended
Low-Cost CPE Transmitter Card
The AD8018ARZ is appropriate for a low-cost customer-premises transmitter card that combines a 5 V rail with high-speed xDSL signaling. The dual-channel 8-pin SOIC reduces placement requirements, and the documented low-distortion operation supports line-reach optimization. Place local decoupling at the supply pins and keep the output network free of unnecessary copper. The final design should be tested across temperature because output swing, load behavior, and distortion can change from the nominal -40°C to +85°C operating range.
Recommended
Recommended Products Summary
Engineering reference data for AD8018ARZ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | AD8014ARZ | THS3201 | MAX4107 | LMH6702 |
|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Analog Devices | Analog Devices | Texas Instruments | Maxim Integrated | Texas Instruments |
| Amplifier Channels | 2 channels | 2 channels | 1 channel | 1 channel | 1 channel |
| Nominal Supply Voltage | 5 V | Similar supply-voltage range | 5 V-class high-speed amplifier | 5 V-class high-speed amplifier | 5 V-class high-speed amplifier |
| Primary Application | xDSL line driving | High-speed signal amplification | High-speed signal amplification | High-speed line-drive amplification | High-speed signal amplification |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Key Differentiators
- Two integrated line-drive amplifier channels in one package (vs THS3201)
- Purpose-defined single-supply xDSL positioning (vs MAX4107)
- High slew rate for fast line transitions (vs AD8014ARZ)
- Dual-channel integration reduces PCB footprint (vs LMH6702)
Design Notes
Place the AD8018ARZ close to the transformer or line-network termination so that each output follows a short, direct path. Avoid long traces and test pads in the high-speed output path, because parasitic inductance and capacitance can degrade edge quality and contribute to distortion. Keep the amplifier ground return continuous and connect it directly to the quiet signal-ground region near the device.
Decouple the 5 V supply locally with the capacitance values and placement guidance specified in the Analog Devices manufacturer datasheet. Place the smallest effective bypass capacitor close to the supply pins and use a larger bulk capacitor near the transmitter supply entry point. Maintain short ground paths for the bypass network so switching current from other sections of the CPE does not modulate the line-driver output.
Evaluate output swing with the actual termination, transformer, cable, and line impedance rather than an unloaded bench condition. The AD8018ARZ can drive low-distortion signals to within 0.5 V of the supply rail, leaving limited headroom for amplitude and load-related loss. Simulate the complete transmit path and verify distortion, overshoot, and stability at the intended xDSL line rate before production release.
Do not treat a functional-equivalent amplifier as an automatic drop-in replacement. Confirm the exact SOIC pinout, supply limits, input common-mode range, gain-bandwidth, output-current capability, and stability with the connected load. The AD8018 is dual-channel, whereas some listed alternatives are single-channel devices, so a substitution may require an additional amplifier and PCB changes despite sharing the 8-pin package class.
Compliance Information
The available product listings identify the part as active and show RoHS-related catalog information, but they do not provide an authoritative compliance statement for every required category. Verify current environmental and quality compliance with the manufacturer before production release.