AD9832BRU - 25 MHz 10-Bit DDS | Analog Devices Inc.
MPN: AD9832BRU ✓ ActiveAD9832BRU Overview
A direct digital synthesizer, or DDS, is a frequency-generation technique in which a digital phase accumulator advances at a controlled rate, addresses stored waveform data, and converts the selected samples through a DAC to create an analog waveform. Within the signal-generation hierarchy, a DDS belongs to the broader family of waveform-generator and clock-and-timing integrated circuits.
The AD9832BRU combines a 25 MHz maximum clock specification with a 32-bit tuning architecture and a 10-bit DAC. Its serial programming interface allows the frequency-control registers to be configured by an embedded controller or host processor. The single DAC output provides a sine waveform without requiring the separate lookup table, DAC, and phase accumulator normally assembled from discrete components.
The device uses a numerically controlled oscillator architecture: the phase accumulator advances on each reference-clock cycle, and a frequency tuning word determines the rate at which the phase moves through the sine look-up table. Changing the tuning word changes the output frequency without changing the external reference clock. The 32-bit accumulator provides fine frequency-control resolution, while the 10-bit converter sets the available output amplitude resolution.
Typical uses include low-cost function generators, waveform sources for test systems, tunable local oscillators, communications test equipment, and embedded sine-wave generation. A digital control path is useful when a system needs to change frequency under software control, sweep an output, or coordinate waveform generation with other instrumentation. A reconstruction or low-pass filter is normally used after the DAC output to remove high-frequency image components.
Designers should treat the DDS as a sampled-output system rather than an ideal analog oscillator. The reference clock, power-supply arrangement, output loading, output filter, and grounding layout directly affect frequency accuracy and spectral purity. Use the Analog Devices AD9832 datasheet and its pin-description table to assign signals and select external components. Avoid assuming unloaded output amplitude or supply limits without checking the specified operating conditions.
This page organizes the AD9832BRU architecture, programming considerations, practical application roles, and verified product information for faster engineering evaluation. It also distinguishes verified electrical facts from parameters that must be confirmed in the manufacturer datasheet, helping designers assess the DDS architecture before beginning schematic capture.
Drop-in alternatives for AD9832BRU — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesAD9832BRU Specifications
| Product Type | Direct digital synthesis IC |
| Maximum Clock Frequency | 25 MHz |
| DAC Resolution | 10 bit |
| Phase Accumulator Resolution | 32 bit |
| Number of DACs | 1 DAC |
| Programming Interface | Serial |
| Output Waveform | Sine wave |
| Architecture | Numerically controlled oscillator |
| Process Technology | CMOS |
| Package | 16-pin TSSOP |
| Mounting Type | Surface mount |
| Lifecycle Status | Production |
AD9832BRU 16-pin tssop Pin Configuration Guide
Pin configuration for AD9832BRU (16-pin tssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for AD9832BRU.
Refer to the datasheet for full pin configuration.
Typical Applications
AD9832BRU is suitable for 6 applications: Programmable Function Generator, Communications Test Equipment, Embedded Sine-Wave Source, Audio-Frequency Signal Testing, Automated Test-System Stimulus, Frequency Reference and Calibration.
Programmable Function Generator
The AD9832BRU suits a basic digital function generator because its 25 MHz maximum clock, 32-bit phase accumulator, and 10-bit DAC generate a programmable sine output from a numerically controlled oscillator. A host controller can load frequency-control words through the serial interface, while the integrated lookup table and DAC reduce external signal-chain complexity. The principal design trade-off is that a reconstruction filter is needed to remove sampled-output images, and the resulting amplitude resolution is 10 bits rather than the higher resolution often desired for precision stimulus generation.
Communications Test Equipment
The AD9832BRU can provide a compact tunable source for communications test equipment requiring software-controlled frequency changes. Its 32-bit tuning architecture offers fine frequency programming, and the 25 MHz clock capability supports the device's specified operating modes. The controller writes the relevant registers over the serial interface, while the DAC creates the analog test signal. In a practical instrument, the reference clock must be clean, the output must be suitably filtered, and the selected operating range must comply with the Analog Devices AD9832 datasheet.
Embedded Sine-Wave Source
The AD9832BRU is useful as an embedded sine-wave source in industrial and instrument-control equipment that needs a locally generated reference rather than a fixed analog oscillator. Firmware can update the 32-bit tuning word to select or sweep the output frequency, and the serial interface allows the DDS to share a control bus with other peripherals. Because the signal originates from a 10-bit DAC, output amplitude, distortion, and unwanted image components depend on the supply design, clock quality, DAC loading, and reconstruction-filter implementation.
Audio-Frequency Signal Testing
The AD9832BRU can generate an audio-frequency sine for speaker, filter, amplifier, and signal-path testing. The 32-bit phase accumulator allows the test system to select frequencies precisely through its frequency tuning word, while the 10-bit DAC provides a compact analog output suitable for general functional tests. For high-fidelity listening evaluation or low-distortion measurements, the generated waveform should be compared with the datasheet noise and distortion limits, and an appropriate reconstruction filter should be added when image rejection is important.
Automated Test-System Stimulus
The AD9832BRU provides a programmable excitation source for automated test systems that sweep stimulus frequency without physically adjusting an analog oscillator. Its serial programming interface supports efficient integration with a test controller, and the integrated phase accumulator, sine lookup table, and DAC simplify the source implementation. Each requested frequency requires the correct tuning-word calculation based on the actual reference-clock frequency. The test system should also account for output settling, filter delay, and the limitations of the 10-bit converter when defining measurement accuracy.
Frequency Reference and Calibration
The AD9832BRU can act as a digitally adjustable reference in laboratory or production-calibration equipment. A stable external clock and a calculated tuning word establish the requested output frequency, making the DDS useful when frequent software-driven frequency selection is more valuable than analog tuning. The Analog Devices AD9832 application guidance includes a simulation utility for calculating the required tuning word and estimating spectral behavior. Calibration results depend on reference-clock accuracy, frequency-word quantization, filter response, and measurement setup.
Engineering reference data for AD9832BRU — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Brand | Analog Devices |
| Package | 16-pin TSSOP |
| Product Type | Direct digital synthesis IC |
| Maximum Clock Frequency | 25 MHz |
| DAC Resolution | 10 bit |
| Phase Accumulator Resolution | 32 bit |
| Number of DACs | 1 DAC |
| Programming Interface | Serial |
| Output Waveform | Sine wave |
| Process Technology | CMOS |
| Lifecycle Status | Production |
Design Notes
Treat the AD9832BRU output as the output of a sampled 10-bit DAC. Place the required reconstruction or low-pass filter close to the analog output, return its ground connection to the device ground, and select the passband around the intended output frequency. Because DDS images are related to the reference clock, changing the clock or tuning word changes the filtering requirement. Use the Analog Devices AD9832 simulation utility to evaluate expected spectral behavior before finalizing the filter.
Assign the reference-clock and serial-interface nets using the pin-description table in the Analog Devices AD9832 datasheet. Keep the clock path compact and away from the analog output and reconstruction-filter components, provide a low-impedance ground return, and decouple the supply pins close to the package. A clean reference clock directly affects frequency accuracy and phase noise, so its source and routing deserve more attention than a generic low-frequency digital signal.
Calculate the frequency tuning word from the actual reference-clock frequency rather than an assumed nominal value; clock error transfers directly into output-frequency error. Also avoid assuming that the register interface of another DDS is interchangeable with the AD9832BRU interface. Firmware must use the AD9832 control-bit definitions, write and update registers in a valid sequence, and account for the time required before the new output frequency is stable.
Compliance Information
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were included in the referenced product information. Confirm current regional compliance statements with Analog Devices.