ADC08832IWM/NOPB - 8-Bit 2-Ch SAR ADC, MICROWIRE, SOIC-14 | TI
MPN: ADC08832IWM/NOPB ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $3.45 | $3.45 |
| 10 | $3.1 | $31.00 |
| 100 | $2.62 | $262.00 |
| 500 | $2.21 | $1,105.00 |
| 1,000 | $1.92 | $1,920.00 |
ADC08832IWM/NOPB Overview
An SAR (successive-approximation-register) ADC is a type of analog-to-digital converter that uses a binary-search algorithm against an internal DAC to converge on the input voltage in N clock cycles, where N is the resolution in bits. SAR ADCs offer a compelling trade-off between speed, power, and accuracy, making them the workhorse of medium-speed data acquisition in embedded, industrial, and instrumentation systems. Within the broader taxonomy, the ADC0822 belongs to the family of data converters, which sit alongside amplifiers, references, and isolation as analog signal-chain building blocks.
Key features include 2 single-ended analog input channels selected via internal multiplexer, ±1 LSB total unadjusted error, zero missing codes over the operating temperature range, TTL/CMOS-compatible I/O, an external clock up to 2 MHz for a maximum 4 microsecond conversion time, and a low-power shutdown mode drawing approximately 3.0 mW. The serial data exchange complies with the NSC MICROWIRE standard so it interfaces directly to COPS-family microcontrollers, PLDs, microprocessors, DSPs, and shift registers using only three I/O pins (CS, CLK, DO). The 14-pin SOIC package provides a familiar through-hole-style footprint in surface-mount form, simplifying retrofits onto existing ADC0831/ADC0832 designs.
The device architecture combines an input multiplexer, sample-and-hold, switched-capacitor DAC, comparator, SAR, and serial output logic on a single CMOS die. Conversion is initiated on the CS falling edge and completed in 4 microseconds at the maximum 2 MHz clock, after which the MSB-first serial word is clocked out on the DO line. Single 5V supply operation eliminates the need for negative rails, while the wide digital logic compatibility (TTL/CMOS compatible I/O) allows direct connection to 5V or 3.3V microcontrollers using simple level-shifting if required.
Typical applications include industrial process control analog front ends, portable battery-powered instrumentation, multi-channel sensor monitoring in HVAC/RSSI-based systems, PLC analog input modules, and embedded data loggers. The integrated multiplexer makes it particularly attractive where two sensors share a single converter channel.
When designing with this device, place a 0.1 microfarat decoupling capacitor as close as possible to the VCC pin and keep analog and digital grounds joined at a single point under the IC. The CS pin must be taken low to initiate conversion, and clock edges should be kept clean to avoid spurious DO transitions.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Drop-in alternatives for ADC08832IWM/NOPB — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ADC08832IWM/NOPB (same form factor and footprint) — differing in Data Interface, Number of Input Channels, Package, Sampling Rate, Input Type.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
ADC08831IWM/NOPB
✅ Drop-In✓ In Stock
$1.39 / Unit
View Datasheet →ADC08832IM/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
ADC08832IN/NOPB
✅ Drop-In✓ In Stock
$2.39 / Unit
View Datasheet →ADC08832IWMX/NOPB
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ADC08832IWM/NOPB Maximum Ratings & Electrical Characteristics
| Resolution | 8 bits |
| Number of Channels | 2 (input multiplexer) |
| Converter Type | SAR (Successive Approximation) |
| Sampling Rate | 153 kS/s (max) |
| Conversion Time | 4 μs (max, fCLK = 2 MHz) |
| Supply Voltage | 5 V DC (single supply) |
| Power Dissipation | 8.5 mW (typical) |
| Low-Power Mode Power | 3.0 mW (typical) |
| Total Unadjusted Error | ±1 LSB |
| Missing Codes | None over temperature |
| Data Interface | MICROWIRE-compatible 3-wire serial |
| I/O Compatibility | TTL/CMOS |
| Sample-and-Hold | Integrated |
| Package | 14-SOIC (IWM) |
| Operating Temperature | -40°C to +85°C (industrial) |
| Mounting Type | Surface Mount |
| RoHS Status | Compliant |
ADC08832IWM/NOPB Pin Configuration
| Pin 1 | VCC — +5V supply |
| Pin 2 | DO — Serial data output (MICROWIRE) |
| Pin 3 | CLK — Serial clock input |
| Pin 4 | CS — Chip select (active low) |
| Pin 5 | GND — Ground |
| Pin 6 | VIN+ — Analog input channel 1 |
| Pin 7 | VIN-/REF — Analog input channel 2 / reference |
| Pin 8 | NC — Not connected (per datasheet) |
| Pin 9 | NC — Not connected (per datasheet) |
| Pin 10 | NC — Not connected (per datasheet) |
| Pin 11 | NC — Not connected (per datasheet) |
| Pin 12 | NC — Not connected (per datasheet) |
| Pin 13 | NC — Not connected (per datasheet) |
| Pin 14 | NC — Not connected (per datasheet) |
Typical Applications
ADC08832IWM/NOPB is suitable for 6 applications: Industrial Process Control Analog Front End, Portable Battery-Powered Instrumentation, PLC Analog Input Module, Multi-Channel Sensor Monitoring (HVAC/RSSI Systems), Embedded Data Logger, Retrofit / Legacy ADC0831/ADC0832 Replacement.
Industrial Process Control Analog Front End
The ADC08832IWM/NOPB fits industrial process control analog front ends where 2 sensors (e.g., temperature and pressure) share one converter channel. The integrated 2-input multiplexer eliminates external analog switches, while ±1 LSB total unadjusted error and zero missing codes over temperature satisfy process-control accuracy requirements. Placed on the field-side of an isolation barrier, the 5V single-supply operation simplifies power design. Its 8-bit resolution and 4us conversion time support update rates up to 153 kS/s, sufficient for thermal/RSSI-based control loops where settling time and noise dominate.
Recommended
Portable Battery-Powered Instrumentation
The ADC08832IWM/NOPB fits portable, battery-powered instrumentation where low power and small PCB area dominate. The 8.5 mW typical operating dissipation and 3.0 mW low-power mode extend battery life in handheld meters and data loggers, while the 14-SOIC package allows compact board layout. According to TI datasheet timing, CS-controlled shutdown between conversions lets the host MCU duty-cycle the ADC. The 4us conversion time at fCLK=2 MHz supports fast sample bursts when needed, enabling responsive touch/RSSI-based measurement cycles in field-portable equipment.
Recommended
PLC Analog Input Module
The ADC08832IWM/NOPB fits PLC analog input modules where multiple analog signals must be digitized with predictable timing. The 2-channel multiplexer allows two field sensors per ADC, halving the BOM count versus single-channel parts; the MICROWIRE serial interface lets a single MCU serve many ADCs via chip-select. According to TI datasheet, the TTL/CMOS-compatible I/O enables 5V direct connection to industrial MCUs. ±1 LSB TUE and no missing codes over the -40 to +85 °C industrial range ensure reliable measurement across factory-floor temperature swings typical of PLC cabinets.
Recommended
Multi-Channel Sensor Monitoring (HVAC/RSSI Systems)
The ADC08832IWM/NOPB fits multi-channel sensor monitoring in HVAC and RSSI-based systems where two analog signals (e.g., temperature and humidity) require periodic sampling. The internal 2-input MUX and sample-and-hold eliminate external components; 153 kS/s throughput over-samples slowly-changing sensor outputs to average out noise. The 5V single supply and TTL/CMOS I/O simplify interface to 5V HVAC controllers. According to TI datasheet, ±1 LSB TUE delivers adequate precision for HVAC setpoint control, and the SOIC-14 footprint eases hand prototyping.
Recommended
Embedded Data Logger
The ADC08832IWM/NOPB fits embedded data loggers that record two analog channels over time. The MICROWIRE serial interface pairs cleanly with low-cost MCUs and shift-register expansion, allowing a single SPI/MICROWIRE port to serve multiple ADCs via chip-select lines. According to TI datasheet, the 3.0 mW low-power mode enables battery duty cycling for long-duration deployments. The 8-bit resolution matches typical environmental sensor precision requirements (temperature, light, soil moisture), making the part a reasonable conversion-in target versus more expensive 12-/16-bit parts.
Recommended
Retrofit / Legacy ADC0831/ADC0832 Replacement
The ADC08832IWM/NOPB fits retrofit applications replacing legacy ADC0831 or ADC0832 with no PCB redesign. According to TI marketing collateral, the '832 is a superior pin-compatible replacement: same 14-SOIC footprint, same MICROWIRE serial protocol, same 4us conversion time, plus an integrated multiplexer and sample-and-hold. Drop-in upgrades can add a second channel without an external analog switch. The 5V single-supply and TTL/CMOS I/O match legacy 5V designs directly, and ±1 LSB TUE exceeds the ADC0831/2 noise performance for cleaner conversion in existing analog signal chains.
Recommended
Recommended Products Summary
Engineering reference data for ADC08832IWM/NOPB — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ADC08831IWM/NOPB | ADC08832IM/NOPB | ADC08832IN/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC (IWM) | 14-SOIC (IWM) - same | 14-SOIC (IWM) - same | 14-SOIC (IWM) - same |
| Resolution | 8 bits | 8 bits | 8 bits | 8 bits |
| Number of Channels | 2 (MUX) | 1 | 2 (MUX) | 2 (MUX) |
| Conversion Time | 4 us (fCLK=2 MHz) | 4 us | 4 us | 4 us |
| Sampling Rate | 153 kS/s | 153 kS/s | 153 kS/s | 153 kS/s |
| Supply Voltage | 5 V DC | 5 V DC | 5 V DC | 5 V DC |
| Power Dissipation | 8.5 mW (3.0 mW low-power) | 8.5 mW | 8.5 mW | 8.5 mW |
| Pinout Variant | 14-SOIC tube | 14-SOIC tube, 1-channel | 14-SOIC tape-and-reel | 14-SOIC industrial temp |
Key Differentiators
- Integrated 2-channel analog multiplexer (vs ADC08831IWM/NOPB)
- Lower power dissipation in low-power mode (vs ADC08831IWM/NOPB)
- Tape-and-reel packaging option for volume production (vs ADC08832IM/NOPB)
Design Notes
Estimated: at VCC=5V and typical operating current of 1.7 mA, the ADC08832IWM/NOPB dissipates approximately 8.5 mW during active conversion, matching the datasheet figure. Decouple VCC (pin 1) with a 0.1 microfarat ceramic capacitor placed within 5 mm of the pin; add a 10 microfarat bulk capacitor if the supply is shared with switching regulators. Use the CS pin to duty-cycle between samples and enter the 3.0 mW low-power mode for battery-powered designs.
Place a single-point ground star under the IC, joining analog GND (pin 5) and digital grounds at the IC. Keep analog input traces short and guarded by ground pours to minimize digital noise pickup on VIN+ (pin 6) and VIN-/REF (pin 7). Route CLK (pin 3) and DO (pin 2) away from analog inputs to reduce conversion noise. According to TI datasheet typical application, the 14-SOIC exposed thermal pad is not present; thermal management is not required for this 8.5 mW part.
Do not leave CS floating; tie CS high through a pull-up resistor so the ADC stays idle and consumes the lowest standby current. According to TI datasheet, conversion starts on the CS falling edge, so a floating CS can cause spurious conversions. Use a 2 MHz maximum CLK frequency and verify timing margin against the 4us conversion time. The 8-bit ADC outputs MSB-first on DO; ensure the host MCU samples DO on the correct CLK edge per the timing spec.
Compliance Information
RoHS compliant per TI product page NOPB suffix. Not AEC-Q100 qualified - the '832 family is designed for industrial/consumer use. Halogen-free per NOPB designation.
