AT91SAM7S16-MU - 55MHz ARM7 MCU | Microchip Technology
MPN: AT91SAM7S16-MU ✗ End of LifeAT91SAM7S16-MU Overview
A microcontroller is a programmable control IC that integrates a processor core, nonvolatile program memory, working RAM, and peripherals on one device. The AT91SAM7S16 belongs to the SAM7S family of embedded processors, combining an ARM7 RISC architecture with serial interfaces and dedicated I/O. It is designed for compact control systems that need deterministic peripheral access without the resource demand of a higher-end application processor.
The principal features of the AT91SAM7S16-MU include a maximum 55 MHz operating frequency, 16 KB of Flash for firmware, and 4 KB of SRAM for data and stack operations. Integrated connectivity includes I2C, SPI, SSC, and UART/USART interfaces. A 21-pin general-purpose I/O complement supports sensors, actuators, indicators, and local control logic, while brown-out detection provides system supervision during supply-voltage disturbances.
The ARM7TDMI core supports a 16/32-bit instruction set and provides a practical balance of processing performance, memory efficiency, and peripheral integration. The SAM7S platform is suitable for control rather than graphics-intensive workloads: typical tasks include acquisition, protocol conversion, sequencing, motor or actuator control, and embedded supervisory functions. Its 48-QFN package supports compact board layouts but requires a PCB with fine-pitch routing and exposed-pad thermal management where appropriate.
Typical uses include industrial automation modules, consumer control equipment, communications equipment, and compact embedded controllers. The I2C and SPI interfaces suit sensor and memory expansion, SSC supports synchronous serial data transfer, and UART/USART enables host or peripheral communication. The 21 available I/O lines make the MCU practical for controlling relays, indicators, switches, and discrete interface circuits.
When designing around this device, plan the power rails and signal levels carefully because the core operates from 1.65 V to 1.95 V. Follow the pin-description and power-layout guidance in the Microchip SAM7S datasheet, place bypass capacitors close to the supply pins, and route high-current or sensitive signals away from switching nodes. Firmware and board compatibility should be validated before replacing a device with a different ARM core or memory configuration.
This product page combines the manufacturer specification, package information, interface capabilities, and practical application guidance into an engineering-focused view of the AT91SAM7S16-MU. It also identifies candidate replacement devices and the key differences that must be checked before any board or firmware change is approved.
Drop-in alternatives for AT91SAM7S16-MU — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with AT91SAM7S16-MU (same form factor and footprint) — differing in Package, Core Size, Instruction Set, Maximum Clock Frequency, Package Code.
AT91SAM7S32B-MU
✅ Drop-In📋 Reference alternative (not in catalog)
ATSAM3S1AA-MU
✅ Drop-InContact for price
View Datasheet →ATSAM3S1AB-MU
✅ Drop-InContact for price
View Datasheet →AT91SAM7S16-MU Maximum Ratings & Electrical Characteristics
| Product Type | 32-bit RISC microcontroller |
| Processor Core | ARM7TDMI |
| Maximum Clock Frequency | 55 MHz |
| Instruction Set | 16/32-bit ARM |
| Flash Program Memory | 16 KB (16K x 8) |
| SRAM | 4 KB (4K x 8) |
| General-Purpose I/O Pins | 21 pins |
| Package | 48-QFN (7 x 7 mm) |
| Mounting Type | Surface mount |
| Core Supply Voltage | 1.65 V to 1.95 V |
| Operating Temperature | -40°C to +85°C |
| Serial Interfaces | I2C, SPI, SSC, and UART/USART |
| Brown-Out Detection | Supported |
| Series | SAM7S |
| Product Family | AT91SAM7S |
| Terminal Count | 48 terminals |
| Package Code | HVQCCN |
AT91SAM7S16-MU hvqccn Pin Configuration Guide
Pin configuration for AT91SAM7S16-MU (hvqccn package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for AT91SAM7S16-MU.
Refer to the datasheet for full pin configuration.
Typical Applications
AT91SAM7S16-MU is suitable for 6 applications: Industrial Sensor Acquisition, Communications Protocol Converter, Consumer Appliance Controller, Motor and Actuator Control, Embedded Security and Access Controller, Data Logger and Monitoring Node.
Industrial Sensor Acquisition
The AT91SAM7S16-MU fits compact sensor-acquisition modules that need deterministic control, local buffering, and flexible serial connectivity. Its ARM7TDMI core operates up to 55 MHz, while 16 KB of Flash stores acquisition firmware and 4 KB of SRAM supports short data buffers and control state. I2C can connect compatible sensors, SPI can serve faster peripherals, and UART/USART can report measurements to a host. The 21 general-purpose I/O lines provide digital status, trigger, alarm, and actuator-control channels. For industrial deployment, observe the specified -40°C to +85°C device range and design the enclosure, isolation, grounding, and transient protection around the complete application rather than the MCU alone.
Recommended
Communications Protocol Converter
The AT91SAM7S16-MU is suitable for protocol-conversion and communications-control modules because it combines UART/USART with SPI, I2C, and SSC in one device. The 55 MHz ARM7TDMI core can service multiple serial tasks, while 21 I/O lines support modem-control signals, indicators, reset control, and interface status. Its 16 KB of Flash accommodates a compact protocol stack, and 4 KB of SRAM supports buffering between interfaces. A converter design should define electrical levels, baud-rate tolerance, isolation, termination, and grounding independently because the MCU-level interfaces do not determine the external transceiver requirements.
Recommended
Consumer Appliance Controller
The AT91SAM7S16-MU can serve as the control hub in a compact consumer appliance where a low-cost, deterministic microcontroller is preferable to a higher-power processor. Its 21 I/O lines can operate displays, buttons, indicators, relays, and motor-control interfaces, while I2C and SPI support sensors and memory expansion. The 55 MHz ARM7TDMI core provides more than enough computation for sequencing, user-interface state machines, and safety monitoring. Firmware size must be checked against 16 KB of Flash, and peak stack use should remain comfortably below the 4 KB SRAM limit to avoid contention during interrupt-heavy operation.
Recommended
Motor and Actuator Control
The AT91SAM7S16-MU fits low-to-medium-complexity actuator controllers that coordinate inputs, timing, and discrete outputs. Its 21 general-purpose I/O lines can handle limit switches, pushbuttons, status LEDs, relay drives, and digital command signals, while the 55 MHz RISC core provides predictable timing for step sequences and fault handling. The device also offers PWM-capable peripheral resources within the SAM7S platform, subject to the exact pin-mux configuration. Place driver transistors or motor-driver circuits outside the MCU, provide appropriate flyback or recirculation paths, and keep switching-current loops away from sensitive serial and clock routing.
Recommended
Embedded Security and Access Controller
The AT91SAM7S16-MU can support compact access-control, keypad, and equipment-security modules when the design requires several I/O events and serial peripherals rather than extensive data storage. The 21 I/O lines can be assigned to keypads, door-position sensing, indicators, and lock-control functions, while UART/USART or I2C supports a reader or secondary controller. The 16 KB Flash footprint favors compact firmware, so cryptographic library size and logging strategy require early review. Brown-out detection adds useful supervision, but production security also depends on secure boot practices, protected keys, physical tamper response, and correct implementation rather than MCU selection alone.
Recommended
Data Logger and Monitoring Node
The AT91SAM7S16-MU is useful for compact monitoring nodes that acquire local measurements, record events, and forward summaries through a serial link. Its 55 MHz core handles protocol formatting and state management, 4 KB of SRAM provides a short working buffer, and I2C, SPI, SSC, and UART/USART support a mix of sensors and communications paths. The limited memory means that bulk storage should use an external interface rather than rely on internal RAM. Validate sustained logging throughput, interrupt latency, timestamp accuracy, and brown-out behavior across the complete input range of 1.65 V to 1.95 V before deployment.
Recommended
Recommended Products Summary
Engineering reference data for AT91SAM7S16-MU — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | AT91SAM7S32B-MU | ATSAM3S1AA-MU | ATSAM3S1AB-MU |
|---|---|---|---|---|
| Package | 48-QFN (7 x 7 mm) | 48-QFN (7 x 7 mm) | 48-QFN (7 x 7 mm) | 48-QFN (7 x 7 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
Key Differentiators
- Compact 16 KB and 4 KB memory configuration (vs AT91SAM7S32B-MU)
- Higher-memory ARM Cortex-M3 migration path (vs ATSAM3S1AB-MU)
- Same 55 MHz clock family with larger memory option (vs AT91SAM7S32B-MU)
Design Notes
Design the supply network around the documented 1.65 V to 1.95 V core range, and determine the external supply pins, sequence, and permissible voltage combinations from the Microchip pin-description table. Place the required bypass capacitors immediately adjacent to their associated supply and ground pins, use the package drawing for exposed-pad connections, and keep the return path short. Confirm that brown-out settings, reset behavior, and external transceiver levels are compatible before connecting them to the 21 I/O pins.
Use the manufacturer 48-QFN land pattern rather than treating the part as a generic no-lead package. The 7 x 7 mm body and 48-terminal arrangement require exact pad geometry, solder-mask design, and paste-volume validation. Maintain short escape routes from fine-pitch pads to bypass capacitors and provide thermal-via patterns beneath the exposed pad when the package drawing calls for them. A board-level assembly process capable of handling the 0.5 mm-class lead pitch should be selected for manufacturing consistency.
Do not treat an equal package as proof of a drop-in replacement. Moving from ARM7TDMI to Cortex-M3 changes startup code, interrupt handling, linker configuration, and some peripheral programming models. The ATSAM3S1AB-MU also operates up to 64 MHz and has substantially more Flash and SRAM than the target. Review the complete manufacturer pin descriptions, clock requirements, peripheral mappings, and electrical limits, then update and regression-test firmware before approving any replacement.
Assign pins from the alternate-function matrix before laying out the board so clock, serial, and debug functions land where they can be routed cleanly. Keep SPI and other high-speed edge-sensitive traces short, provide controlled return paths beneath them, and separate switching-node wiring from communication and sensor inputs. Use series damping or other edge-control measures only after analyzing the actual edge rate and trace topology. Validate signal levels and timing with the production clock, load, and peripheral configuration.
Compliance Information
The industrial temperature range is documented, but no specific RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified for this orderable MPN.