Microchip Technology

AT91SAM7S16-MU - 55MHz ARM7 MCU | Microchip Technology

N.º da peça: AT91SAM7S16-MU ✗ Fim de vida
1.65 V to 1.95 V Vdss 48-QFN (7 x 7 mm) Package 55 MHz Speed 16 KB (16K x 8) Memory
MOQ: 1 |

AT91SAM7S16-MU Visão geral

Microchip Technology AT91SAM7S16-MU is a 32-bit RISC microcontroller with an ARM7TDMI core operating up to 55 MHz, 16 KB of embedded Flash program memory, and 4 KB of SRAM in a 48-QFN 7 x 7 mm package. The device provides 21 general-purpose I/O pins and an industrial temperature range of -40°C to +85°C. Its operating core supply range is 1.65 V to 1.95 V.

A microcontroller is a programmable control IC that integrates a processor core, nonvolatile program memory, working RAM, and peripherals on one device. The AT91SAM7S16 belongs to the SAM7S family of embedded processors, combining an ARM7 RISC architecture with serial interfaces and dedicated I/O. It is designed for compact control systems that need deterministic peripheral access without the resource demand of a higher-end application processor.

The principal features of the AT91SAM7S16-MU include a maximum 55 MHz operating frequency, 16 KB of Flash for firmware, and 4 KB of SRAM for data and stack operations. Integrated connectivity includes I2C, SPI, SSC, and UART/USART interfaces. A 21-pin general-purpose I/O complement supports sensors, actuators, indicators, and local control logic, while brown-out detection provides system supervision during supply-voltage disturbances.

The ARM7TDMI core supports a 16/32-bit instruction set and provides a practical balance of processing performance, memory efficiency, and peripheral integration. The SAM7S platform is suitable for control rather than graphics-intensive workloads: typical tasks include acquisition, protocol conversion, sequencing, motor or actuator control, and embedded supervisory functions. Its 48-QFN package supports compact board layouts but requires a PCB with fine-pitch routing and exposed-pad thermal management where appropriate.

Typical uses include industrial automation modules, consumer control equipment, communications equipment, and compact embedded controllers. The I2C and SPI interfaces suit sensor and memory expansion, SSC supports synchronous serial data transfer, and UART/USART enables host or peripheral communication. The 21 available I/O lines make the MCU practical for controlling relays, indicators, switches, and discrete interface circuits.

When designing around this device, plan the power rails and signal levels carefully because the core operates from 1.65 V to 1.95 V. Follow the pin-description and power-layout guidance in the Microchip SAM7S datasheet, place bypass capacitors close to the supply pins, and route high-current or sensitive signals away from switching nodes. Firmware and board compatibility should be validated before replacing a device with a different ARM core or memory configuration.

This product page combines the manufacturer specification, package information, interface capabilities, and practical application guidance into an engineering-focused view of the AT91SAM7S16-MU. It also identifies candidate replacement devices and the key differences that must be checked before any board or firmware change is approved.

Alternativas drop-in para AT91SAM7S16-MU — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com AT91SAM7S16-MU (mesmo formato e footprint) — diferindo em Package, Core Size, Instruction Set, Maximum Clock Frequency, Package Code.

Microchip Technology
Package: 48-QFN (7x7 mm)
Core Size: 32-bit
Instruction Set: Thumb-2
Comparar com AT91SAM7S16-MU →
Microchip Technology
Package: 48-QFN (7x7 mm) with Exposed Pad
Core Size: 32-Bit Single-Core
Maximum Clock Frequency: 64 MHz
Comparar com AT91SAM7S16-MU →

AT91SAM7S32B-MU

✅ Drop-In
📦 48-QFN (7 x 7 mm)
Flash increases from 16 KB to 32 KB (+100%) and SRAM from 4 KB to 8 KB (+100%); clock and peripheral compatibility still require pin-table confirmation

📋 Alternativa de referência (fora do catálogo)

ATSAM3S1AA-MU

✅ Drop-In
Microchip Technology
📦 48-QFN (7 x 7 mm)
ARM Cortex-M3 (revision 2.0) · 32-bit · 64 MHz · 64 KB (64K x 8) Flash · 16 KB (16K x 8) · 1.62 V to 3.6 V · 1.08 V to 1.32 V (internal regulator) · 48-QFN (7x7 mm)

Consulte o preço

Ver ficha técnica →

ATSAM3S1AB-MU

✅ Drop-In
Microchip Technology
📦 48-QFN (7 x 7 mm)
ARM Cortex-M3 · 32-Bit Single-Core · 64 MHz · 64 KB (64K x 8) · 16 KB · 1.62 V to 3.6 V · 48-QFN (7x7 mm) with Exposed Pad · HVQCCN (48-VFQFN Exposed Pad)

Consulte o preço

Ver ficha técnica →

AT91SAM7S16-MU Classificações máximas e características elétricas

Product Type 32-bit RISC microcontroller
Processor Core ARM7TDMI
Frequência máxima de clock 55 MHz
Instruction Set 16/32-bit ARM
Flash Program Memory 16 KB (16K x 8)
SRAM 4 KB (4K x 8)
General-Purpose I/O Pins 21 pins
Encapsulamento 48-QFN (7 x 7 mm)
Tipo de montagem Surface mount
Core Supply Voltage 1.65 V to 1.95 V
Temperatura de operação -40°C to +85°C
Serial Interfaces I2C, SPI, SSC, and UART/USART
Brown-Out Detection Supported
Series SAM7S
Product Family AT91SAM7S
Terminal Count 48 terminals
Package Code HVQCCN

Guia de Configuração de Pinos do AT91SAM7S16-MU hvqccn

Configuração de pinos para AT91SAM7S16-MU (pacote hvqccn). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.

Diagrama de pinagem do pacote hvqccn para AT91SAM7S16-MU

Nenhum dado detalhado de pinagem disponível para AT91SAM7S16-MU.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

AT91SAM7S16-MU é adequado para 6 aplicaçãos: Industrial Sensor Acquisition, Communications Protocol Converter, Consumer Appliance Controller, Motor and Actuator Control, Embedded Security and Access Controller, Data Logger and Monitoring Node.

🏭

Industrial Sensor Acquisition

The AT91SAM7S16-MU fits compact sensor-acquisition modules that need deterministic control, local buffering, and flexible serial connectivity. Its ARM7TDMI core operates up to 55 MHz, while 16 KB of Flash stores acquisition firmware and 4 KB of SRAM supports short data buffers and control state. I2C can connect compatible sensors, SPI can serve faster peripherals, and UART/USART can report measurements to a host. The 21 general-purpose I/O lines provide digital status, trigger, alarm, and actuator-control channels. For industrial deployment, observe the specified -40°C to +85°C device range and design the enclosure, isolation, grounding, and transient protection around the complete application rather than the MCU alone.

🌐

Communications Protocol Converter

The AT91SAM7S16-MU is suitable for protocol-conversion and communications-control modules because it combines UART/USART with SPI, I2C, and SSC in one device. The 55 MHz ARM7TDMI core can service multiple serial tasks, while 21 I/O lines support modem-control signals, indicators, reset control, and interface status. Its 16 KB of Flash accommodates a compact protocol stack, and 4 KB of SRAM supports buffering between interfaces. A converter design should define electrical levels, baud-rate tolerance, isolation, termination, and grounding independently because the MCU-level interfaces do not determine the external transceiver requirements.

📱

Consumer Appliance Controller

The AT91SAM7S16-MU can serve as the control hub in a compact consumer appliance where a low-cost, deterministic microcontroller is preferable to a higher-power processor. Its 21 I/O lines can operate displays, buttons, indicators, relays, and motor-control interfaces, while I2C and SPI support sensors and memory expansion. The 55 MHz ARM7TDMI core provides more than enough computation for sequencing, user-interface state machines, and safety monitoring. Firmware size must be checked against 16 KB of Flash, and peak stack use should remain comfortably below the 4 KB SRAM limit to avoid contention during interrupt-heavy operation.

🔧

Motor and Actuator Control

The AT91SAM7S16-MU fits low-to-medium-complexity actuator controllers that coordinate inputs, timing, and discrete outputs. Its 21 general-purpose I/O lines can handle limit switches, pushbuttons, status LEDs, relay drives, and digital command signals, while the 55 MHz RISC core provides predictable timing for step sequences and fault handling. The device also offers PWM-capable peripheral resources within the SAM7S platform, subject to the exact pin-mux configuration. Place driver transistors or motor-driver circuits outside the MCU, provide appropriate flyback or recirculation paths, and keep switching-current loops away from sensitive serial and clock routing.

🧩

Embedded Security and Access Controller

The AT91SAM7S16-MU can support compact access-control, keypad, and equipment-security modules when the design requires several I/O events and serial peripherals rather than extensive data storage. The 21 I/O lines can be assigned to keypads, door-position sensing, indicators, and lock-control functions, while UART/USART or I2C supports a reader or secondary controller. The 16 KB Flash footprint favors compact firmware, so cryptographic library size and logging strategy require early review. Brown-out detection adds useful supervision, but production security also depends on secure boot practices, protected keys, physical tamper response, and correct implementation rather than MCU selection alone.

📺

Data Logger and Monitoring Node

The AT91SAM7S16-MU is useful for compact monitoring nodes that acquire local measurements, record events, and forward summaries through a serial link. Its 55 MHz core handles protocol formatting and state management, 4 KB of SRAM provides a short working buffer, and I2C, SPI, SSC, and UART/USART support a mix of sensors and communications paths. The limited memory means that bulk storage should use an external interface rather than rely on internal RAM. Validate sustained logging throughput, interrupt latency, timestamp accuracy, and brown-out behavior across the complete input range of 1.65 V to 1.95 V before deployment.

What are the key specifications of AT91SAM7S16-MU that engineers should know?
The AT91SAM7S16-MU is a 32-bit RISC microcontroller with an ARM7TDMI core, a maximum operating frequency of 55 MHz, 16 KB of Flash memory, and 4 KB of SRAM. It provides 21 general-purpose I/O pins in a 48-QFN 7 x 7 mm package. According to Microchip document doc6175, the device belongs to the SAM7S family and supports I2C, SPI, SSC, and UART/USART connectivity, making it suitable for compact embedded-control and data-acquisition systems.
What is the operating voltage of the AT91SAM7S16-MU?
The AT91SAM7S16-MU core operates from 1.65 V to 1.95 V. According to the Microchip SAM7S technical documentation, the exact external supply arrangement should be selected from the device pinout and power-entry scheme rather than inferred from the core range alone. Before layout or replacement work, verify every supply and I/O voltage against the manufacturer pin-description table, especially when connecting 3.3 V peripherals.
How much memory and I/O does the AT91SAM7S16-MU provide?
The AT91SAM7S16-MU provides 16 KB of Flash program memory, 4 KB of SRAM, and 21 general-purpose I/O lines. According to Microchip document doc6175, the SAM7S16 is the smallest-memory member listed for the SAM7S family and differs from larger family members in memory size, peripheral configuration, and package options. Its compact memory footprint suits embedded firmware that does not require a large local buffer or graphical user interface.
Which communication interfaces are available on AT91SAM7S16-MU?
The AT91SAM7S16-MU includes I2C, SPI, SSC, and UART/USART interfaces. According to the Microchip product documentation, these peripherals cover common embedded-control links to sensors, memories, converters, and external controllers. I2C supports low-pin-count peripheral expansion, SPI supports higher-throughput full-duplex transfers, and UART/USART provides asynchronous serial communication. Pin multiplexing must be checked against the selected board configuration.
Where can I download the AT91SAM7S16-MU datasheet PDF?
The AT91SAM7S16-MU datasheet PDF can be downloaded from the Microchip document link on this page. The primary document is Microchip doc6175, which covers the SAM7S family. According to Microchip, the SAM7S512, SAM7S256, SAM7S128, SAM7S64, SAM7S321, SAM7S32, SAM7S161, and SAM7S16 devices differ in memory size, peripheral set, and package, so use the device-specific ordering information when interpreting shared family guidance.
Where can I find the AT91SAM7S16-MU pinout?
The AT91SAM7S16-MU uses a 48-QFN 7 x 7 mm package, and its authoritative pin assignments are shown in the Microchip SAM7S documentation and the manufacturer product description. Use the pin-description table to assign power, ground, reset, clock, and I/O functions. The package is fine pitch and includes 48 terminals, so verify land-pattern geometry and exposed-pad requirements against the package drawing rather than relying only on a generic QFN symbol.
Where can I buy AT91SAM7S16-MU and request current availability?
Use the Request a Quote form on this page to request AT91SAM7S16-MU availability, current sourcing terms, and an appropriate order quantity. The manufacturer identifies the device in a 48-QFN package, while current channel records indicate that legacy inventory and sourcing support may vary. Because lifecycle status and stock can change, request a written confirmation of quantity, condition, packaging, and lead time before committing a production order.
What is the price of AT91SAM7S16-MU?
Current AT91SAM7S16-MU pricing depends on order quantity, condition, packaging, and market availability. Submit the Request a Quote form on this page with the required quantity and packaging preference to obtain a current quotation. The platform keeps the commercial response attached to this exact 48-QFN orderable MPN, helping distinguish the original AT91SAM7S16-MU from related SAM7S devices whose memory or package configurations differ.
What is the lead time for AT91SAM7S16-MU?
The current lead time for AT91SAM7S16-MU should be confirmed through the Request a Quote form on this page. Lead time can vary with quantity, manufacturing condition, authorized-channel allocation, and replenishment status. Microchip documentation identifies the device as an ARM7 SAM7S microcontroller in a 48-QFN package, but a current supply commitment should accompany the quotation before it is treated as a production planning input.
Is AT91SAM7S16-MU in stock?
AT91SAM7S16-MU availability should be confirmed through the Request a Quote form on this page rather than inferred from a product listing. The part is an established 48-QFN legacy microcontroller, and inventory can fluctuate as channels replenish or allocate remaining stock. Include your required quantity, date code needs, and acceptable manufacturing or remnant condition in the request to receive an actionable availability response.
What is the best drop-in replacement for AT91SAM7S16-MU?
The best drop-in replacement must match the 48-QFN land pattern, pin functions, electrical limits, and embedded peripheral requirements. ATSAM3S1AA-MU and ATSAM3S1AB-MU are documented comparison candidates in the 48-QFN class, while AT91SAM7S32B-MU is a higher-memory SAM7S-family option. None should be approved as a drop-in solely from package similarity; compare the manufacturer pin tables, memory capacity, clock requirements, interrupt mapping, startup sequence, and firmware dependencies first.
Can ATSAM3S1AB-MU replace AT91SAM7S16-MU?
ATSAM3S1AB-MU can be considered as a migration candidate, but it is not automatically a drop-in replacement for AT91SAM7S16-MU. The documented comparison identifies a Cortex-M3 core operating up to 64 MHz, 64 KB of Flash, and 16 KB of SRAM, versus the AT91SAM7S16-MU's ARM7TDMI core at up to 55 MHz, 16 KB of Flash, and 4 KB of SRAM. The 64 MHz clock is about 16% higher, while memory capacities increase by 300%, so board and firmware compatibility require validation.
Is AT91SAM7S16-MU suitable for industrial automation?
The AT91SAM7S16-MU is suitable for many compact industrial automation and supervisory-control tasks. Its 55 MHz ARM7TDMI core, 21 general-purpose I/O lines, brown-out detection, and I2C, SPI, SSC, and UART/USART interfaces provide useful acquisition and control resources. Its specified -40°C to +85°C temperature range supports extended industrial environments, although the complete assembly must also satisfy enclosure temperature, surge, isolation, and functional-safety requirements.
When should I choose AT91SAM7S16-MU instead of AT91SAM7S32B-MU?
Choose AT91SAM7S16-MU when firmware and working data fit within 16 KB of Flash and 4 KB of SRAM and the application does not require the additional memory of AT91SAM7S32B-MU. The latter part provides 32 KB of Flash and 8 KB of SRAM in the listed SAM7S family comparison, twice the target memory capacities. Retain AT91SAM7S16-MU for legacy boards and tightly constrained code footprints, but verify the complete package and peripheral configuration before treating either device as interchangeable.
How does AT91SAM7S16-MU compare with a general-purpose 32-bit microcontroller?
The AT91SAM7S16-MU is a 32-bit RISC controller centered on an ARM7TDMI core, with 16 KB of Flash, 4 KB of SRAM, 21 I/O pins, and four named serial-interface families. According to Microchip document doc6175, the SAM7S family targets embedded-control applications where memory size and peripheral configuration distinguish individual devices. It is appropriate when deterministic embedded control is required, but it is less suitable than a larger-memory MCU for intensive computation, complex graphics, or extensive protocol stacks.
What can replace AT91SAM7S16-MU in an embedded design?
A replacement must preserve the 48-QFN footprint, electrical behavior, and required peripheral functions. Documented candidates include ATSAM3S1AA-MU, ATSAM3S1AB-MU, and AT91SAM7S32B-MU, but each changes at least one major design input: core architecture, clock, memory capacity, or family configuration. Treat them as redesign or migration candidates until the manufacturer pin tables, startup code, linker configuration, peripheral mapping, and operating limits have been checked against the original schematic and firmware.

Dados de referência de engenharia para AT91SAM7S16-MU — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the AT91SAM7S16-MU when an existing ARM7-based design fits within 16 KB of Flash and 4 KB of SRAM, operates at up to 55 MHz, and uses the established SAM7S peripheral set. It is especially appropriate for maintaining legacy 48-QFN boards whose software and peripheral assignments depend on the ARM7TDMI architecture. Select AT91SAM7S32B-MU when the same family can supply twice the Flash and SRAM while retaining the 55 MHz clock position. Consider ATSAM3S1AA-MU only after checking its complete pin and peripheral configuration. ATSAM3S1AB-MU is a redesign candidate rather than an automatic substitution because it changes to Cortex-M3, raises the maximum clock to 64 MHz, and increases both memory capacities by 300%. For every candidate, review the manufacturer pin tables, startup code, clock tree, interrupt layout, linker settings, and board-level electrical requirements before production approval.

Comparação com alternativas

Parâmetro Este produto AT91SAM7S32B-MU ATSAM3S1AA-MU ATSAM3S1AB-MU
Package 48-QFN (7 x 7 mm) 48-QFN (7 x 7 mm) 48-QFN (7 x 7 mm) 48-QFN (7 x 7 mm)
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology

Principais diferenciais

  • Compact 16 KB and 4 KB memory configuration (vs AT91SAM7S32B-MU)
  • Higher-memory ARM Cortex-M3 migration path (vs ATSAM3S1AB-MU)
  • Same 55 MHz clock family with larger memory option (vs AT91SAM7S32B-MU)

Notas de projeto

Design the supply network around the documented 1.65 V to 1.95 V core range, and determine the external supply pins, sequence, and permissible voltage combinations from the Microchip pin-description table. Place the required bypass capacitors immediately adjacent to their associated supply and ground pins, use the package drawing for exposed-pad connections, and keep the return path short. Confirm that brown-out settings, reset behavior, and external transceiver levels are compatible before connecting them to the 21 I/O pins.

Use the manufacturer 48-QFN land pattern rather than treating the part as a generic no-lead package. The 7 x 7 mm body and 48-terminal arrangement require exact pad geometry, solder-mask design, and paste-volume validation. Maintain short escape routes from fine-pitch pads to bypass capacitors and provide thermal-via patterns beneath the exposed pad when the package drawing calls for them. A board-level assembly process capable of handling the 0.5 mm-class lead pitch should be selected for manufacturing consistency.

Do not treat an equal package as proof of a drop-in replacement. Moving from ARM7TDMI to Cortex-M3 changes startup code, interrupt handling, linker configuration, and some peripheral programming models. The ATSAM3S1AB-MU also operates up to 64 MHz and has substantially more Flash and SRAM than the target. Review the complete manufacturer pin descriptions, clock requirements, peripheral mappings, and electrical limits, then update and regression-test firmware before approving any replacement.

Assign pins from the alternate-function matrix before laying out the board so clock, serial, and debug functions land where they can be routed cleanly. Keep SPI and other high-speed edge-sensitive traces short, provide controlled return paths beneath them, and separate switching-node wiring from communication and sensor inputs. Use series damping or other edge-control measures only after analyzing the actual edge rate and trace topology. Validate signal levels and timing with the production clock, load, and peripheral configuration.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The industrial temperature range is documented, but no specific RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified for this orderable MPN.

Dados verificados em: 2026-11-10 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

AT91SAM7S16-MU datasheet AT91SAM7S16-MU pinout AT91SAM7S16-MU datasheet pdf AT91SAM7S16-MU specifications AT91SAM7S16-MU 48-QFN AT91SAM7S16-MU equivalent AT91SAM7S16-MU replacement AT91SAM7S16-MU cross reference AT91SAM7S16-MU vs ATSAM3S1AB-MU AT91SAM7S16-MU price AT91SAM7S16-MU stock Microchip AT91SAM7S16-MU AT91SAM7S16-MU ARM7TDMI AT91SAM7S16-MU industrial controller

Componentes & termos relacionados

Microchip Technology AT91SAM7S16-MU AT91SAM7S32B-MU ATSAM3S1AA-MU ATSAM3S1AB-MU ARM7TDMI Arm Cortex-M3 32-bit RISC microcontroller microcontroller embedded processor semiconductor SAM7S series Flash program memory SRAM 55 MHz 21 general-purpose I/O I2C SPI SSC UART/USART brown-out detection 48-QFN package QFN family surface-mount package industrial automation communication controller
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ