ATF16V8BQL-15XU - 15ns Flash PLD | Microchip Technology
MPN: ATF16V8BQL-15XU ✓ ActiveATF16V8BQL-15XU Overview
A simple programmable logic device, or SPLD, is a programmable-logic IC within the broader CPLD and FPGA hierarchy. It provides a fixed, electrically programmable logic structure that engineers can configure for Boolean equations, product-term logic, registered outputs, and state-machine functions. The ATF16V8BQL architecture is especially useful when a design needs more control than a fixed gate array but less complexity, cost, or routing overhead than an FPGA.
Key features include a 15 ns propagation delay grade, 8 macrocells, 250 gates, and three automatically selected operating modes. The Flash configuration memory allows the device to be reprogrammed without removable programming adapters. Input Transition Detection circuitry recognizes activity on inputs and automatically places an idle device into a low-power state, with typical standby current of 5 mA. Internal pull-up resistors are provided on inputs and I/Os, reducing the need for external bias components in many designs.
The ATF16V8BQL incorporates a superset of the generic 16R8 architecture, allowing direct replacement of 16R8 devices and compatibility with many 20-pin combinatorial PLDs. Each of the 8 macrocells has eight product terms, and the configuration architecture supports combinational, complex macrocell, and registered modes. JEDEC file preload and a 64-bit user signature area support controlled manufacturing workflows and device identification.
Typical applications include industrial control and data-acquisition interfaces, address decoding, peripheral glue logic, legacy protocol conversion, and small state machines. The 20-TSSOP package is useful where a 5 V supply is available and board area is more constrained than with a leaded DIP package. Its nonvolatile Flash configuration also suits designs that require field updates or production programming after board assembly.
Designers should verify the exact operating mode, output polarity, feedback assignment, and pin behavior against the manufacturer datasheet before replacing an existing GAL16V8-class circuit. PCB layouts must preserve the pin orientation and leave adequate routing clearance around the TSSOP body. Power and ground connections should be short and decoupled to prevent configuration or output-edge irregularities.
This product page combines the manufacturer device information, package and timing details, sourcing information, replacement guidance, and practical design guidance to support component selection and PCB implementation. The comparison data also distinguishes same-package drop-in options from alternatives that require a package change.
Drop-in alternatives for ATF16V8BQL-15XU — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ATF16V8BQL-15XU (same form factor and footprint) — differing in Maximum Inputs, Package.
ATF16V8BQL-15XI
✅ Drop-InContact for price
View Datasheet →ATF16V8BQL-10XI
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ATF16V8BQL-10XU
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
ATF16V8BQL-15XU
✅ Drop-InContact for price
View Datasheet →ATF16V8BQL-15SU
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →ATF16V8BQL-15XU Maximum Ratings & Electrical Characteristics
| Device Type | Electrically Erasable Programmable Logic Device (EEPLD) |
| Architecture | Simple Programmable Logic Device (SPLD) |
| Macrocells | 8 macrocells |
| Propagation Delay | 15 ns |
| Gate Equivalent Capacity | 250 gates |
| Maximum Inputs | Up to 16 inputs |
| User I/O Count | 8 I/Os |
| Total Package Pins | 20 pins |
| Supply Voltage | 5 V |
| Configuration Memory | Electrically erasable Flash memory |
| Standby Current | 5 mA typical |
| Low-Power Control | Input Transition Detection (ITD) |
| Input Biasing | Internal pull-up resistors on inputs and I/Os |
| Configuration Support | JEDEC file preload |
| User Signature Storage | 64 bits |
| Logic Family | CMOS |
| Package | 20-TSSOP |
| Mounting Type | Surface mount |
| RoHS Status | ROHS3 compliant |
ATF16V8BQL-15XU Pin Configuration
| Pin 1 | CLK — Clock input |
| Pin 2 | I7 — Dedicated input |
| Pin 3 | I6 — Dedicated input |
| Pin 4 | I5 — Dedicated input |
| Pin 5 | I4 — Dedicated input |
| Pin 6 | I3 — Dedicated input |
| Pin 7 | I2 — Dedicated input |
| Pin 8 | I1 — Dedicated input |
| Pin 9 | I0 — Dedicated input |
| Pin 10 | GND — Ground connection |
| Pin 11 | OE — Output enable input |
| Pin 12 | CE — Chip enable input |
| Pin 13 | I/O0 — Configurable input/output |
| Pin 14 | I/O1 — Configurable input/output |
| Pin 15 | I/O2 — Configurable input/output |
| Pin 16 | I/O3 — Configurable input/output |
| Pin 17 | I/O4 — Configurable input/output |
| Pin 18 | I/O5 — Configurable input/output |
| Pin 19 | I/O6 — Configurable input/output |
| Pin 20 | I/O7 — Configurable input/output |
Typical Applications
ATF16V8BQL-15XU is suitable for 6 applications: Industrial Control and Address Decoding, Data-Acquisition Interface Logic, Peripheral Glue Logic, Legacy Protocol Conversion, Small State-Machine Control, Programmable Test and Measurement Logic.
Industrial Control and Address Decoding
The ATF16V8BQL-15XU fits industrial control boards that require address decoding, command qualification, or interlock logic close to the associated processor. Its 8 macrocells and 15 ns speed grade can implement several Boolean equations or registered state functions, while the 20-TSSOP package reduces board area compared with leaded implementations. Electrically erasable Flash permits configuration changes without socketed parts. Internal input pull-ups can simplify unused or control-input biasing, but engineers should still verify every input state and macrocell polarity against the manufacturer pin and mode tables.
Recommended
Data-Acquisition Interface Logic
The ATF16V8BQL-15XU can coordinate data-acquisition peripherals by combining write strobes, chip selects, interrupt requests, and bus-control signals in a small number of macrocells. A 15 ns propagation-delay grade is useful for logic close to the acquisition device, while the 5 V architecture matches systems using legacy TTL-compatible interfaces. Its three operating modes allow the same physical device to be assigned to combinational, complex macrocell, or registered configurations by the design software. Verify setup and hold timing at the system level and avoid using Flash reprogramming as a substitute for a designed recovery or configuration mechanism.
Recommended
Peripheral Glue Logic
The ATF16V8BQL-15XU is well suited to peripheral glue logic where several control signals must be combined into enables, resets, or status outputs. Its 8 macrocells provide enough product-term capacity for moderate combinational functions, and the 20-TSSOP footprint supports compact interface sections on mixed-signal and control boards. Automatic configuration-mode selection simplifies use of the superset 16R8-compatible architecture. Designers should keep the output enable and chip-enable behavior consistent with the intended reset strategy, and should confirm propagation delay after adding cable, connector, or level-shifter delays at the board boundary.
Recommended
Legacy Protocol Conversion
The ATF16V8BQL-15XU can bridge protocol differences in legacy equipment by translating control sequences, converting signal polarity, or generating handshake signals between otherwise incompatible logic domains. Its electrically erasable Flash configuration allows the conversion map to be revised during development or maintenance, while 8 macrocells provide compact state and decode functions. The device is most appropriate when timing requirements are moderate and the protocol state count remains small. Validate signal polarity, reset behavior, and clock-domain boundaries, especially when the converted interface operates at a substantially different clock frequency.
Recommended
Small State-Machine Control
The ATF16V8BQL-15XU supports compact state-machine implementations in sequencing, mode control, and fault-response circuits. The registered macrocell mode is useful for retaining state between clock edges, while the 15 ns speed class provides a defined timing grade for short combinational paths. Input Transition Detection allows the device to enter its low-power idle state when the monitored inputs stop changing, with a typical standby current of 5 mA. Validate recovery after a state transition, power-up reset requirements, and every registered output assignment before releasing the design for production programming.
Recommended
Programmable Test and Measurement Logic
The ATF16V8BQL-15XU can implement deterministic fixture routing, pattern qualification, and instrument-control logic in compact test systems. Its 8 macrocells are appropriate for combining enable paths and sequencing commands, while Flash configuration supports repeatable updates when test plans change. The 20-TSSOP package is particularly useful on dense tester daughterboards, and internal pull-ups can reduce discrete components on control lines. Designers should account for fixture propagation delay, use the 15 ns device grade only after timing analysis, and ensure that configuration retention and programming permissions are integrated into the production process.
Recommended
Recommended Products Summary
Engineering reference data for ATF16V8BQL-15XU — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ATF16V8BQL-15XI | ATF16V8BQL-10XI | ATF16V8BQL-10XU | ATF16V8BQL-15XU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP | 20-TSSOP |
| Device Type | EEPLD | EEPLD | EEPLD | EEPLD | EEPLD |
| Macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Propagation Delay | 15 ns | 15 ns | 10 ns | 10 ns | 15 ns |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Gate Equivalent Capacity | 250 gates | 250 gates | 250 gates | 250 gates | 250 gates |
| Configuration Memory | Electrically erasable Flash memory | Electrically erasable Flash memory | Electrically erasable Flash memory | Electrically erasable Flash memory | Electrically erasable Flash memory |
| Low-Power Feature | Input Transition Detection with automatic low-power mode | Input Transition Detection with automatic low-power mode | Input Transition Detection with automatic low-power mode | Input Transition Detection with automatic low-power mode | Input Transition Detection with automatic low-power mode |
| Input Pull-Up Resistors | Internal pull-ups on inputs and I/Os | Internal pull-ups on inputs and I/Os | Internal pull-ups on inputs and I/Os | Internal pull-ups on inputs and I/Os | Internal pull-ups on inputs and I/Os |
Key Differentiators
- Directly documented same-package electrical match (vs ATF16V8BQL-15XI)
- Faster timing option from the same ATF16V8BQL family (vs ATF16V8BQL-10XU)
- Compact programmable logic with automatic idle control (vs GAL16V8B-25LP)
Design Notes
Follow the manufacturer’s 20-TSSOP land pattern exactly and verify pin 1 orientation against the PCB assembly drawing. Keep CLK traces short and isolate them from nearby switching nodes because a programmed output edge can affect downstream timing even when the logic equation itself is correct. Use a solid ground plane, avoid split planes beneath the device, and provide a short return path for every clock and control input.
Provide a stable 5 V supply and place the local decoupling capacitor close to the device power and ground pins. Determine the capacitor value from the manufacturer’s recommended application circuit and the switching activity of adjacent circuitry. Check the supply ramp, power-up behavior, and output states against the system requirements; Flash reprogrammability does not imply that every configuration is safe during an uncontrolled power ramp.
Do not substitute a PDIP, SOIC, or PLCC device onto the 20-TSSOP footprint without redesigning the land pattern. Also verify that a proposed replacement supports the same macrocell architecture, feedback assignment, operating mode, JEDEC programming file, and user-signature procedure. A matching speed grade alone is insufficient for a safe drop-in decision.
Treat outputs driving external cables, relays, or long traces as potential sources of ringing and overshoot. Add the output loading and edge-rate assumptions to system timing analysis, and use series damping or a suitable driver when edge rates exceed the board’s practical limit. Preserve the common ground reference between the PLD and connected peripheral because Input Transition Detection and internal pull-up behavior depend on valid input levels.
Compliance Information
ROHS3 compliance is identified for the ATF16V8BQL-15XU. No verified statement establishes REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status.