BTS723GWXUMA1 - 2.5A Dual High-Side PROFET Switch | Infineon
MPN: BTS723GWXUMA1 β Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $2.18 | $2.18 |
| 10 | $1.89 | $18.90 |
| 100 | $1.62 | $162.00 |
| 500 | $1.41 | $705.00 |
| 1,000 | $1.24 | $1,240.00 |
Drop-in alternatives for BTS723GWXUMA1 β same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Quick Comparison Tool β Select alternative parts for side-by-side comparison:
BTS723GW
β Drop-Inπ Reference alternative (not in catalog)
BTS724L2
β Drop-Inπ Reference alternative (not in catalog)
BTS721L1
β Drop-Inπ Reference alternative (not in catalog)
BTS5215LAUMA1
β Drop-Inβ In Stock
$1.18 / Unit
View Datasheet βBTS723GWXUMA1 Maximum Ratings & Electrical Characteristics
| Product Type | Smart High-Side Power Switch |
| Number of Channels | 2 (dual independent high-side) |
| Technology | Classic PROFETβ’ (SMART7 vertical N-channel) |
| Nominal Operating Voltage (Vbb) | 6 V to 24 V |
| Load-Dump Survivability (Vbb(load-dump)) | Up to 40 V (per Classic PROFET spec) |
| Continuous Load Current per Channel (I_L(nom)) | 2.5 A |
| Standby Current (I_bb(off)) | Very low (a few Β΅A typical) |
| Input Logic Compatibility | CMOS-compatible |
| Diagnostic Output | Current-mirror status / fault flag (shared) |
| Protection Features | Overload, short circuit, ESD, over-temperature, over-voltage (active clamp) |
| Inductive Load Switching | Active Zener clamp for fast demagnetization |
| Operating Temperature Range | -40 C to +150 C (junction) |
| Package | PG-DSO-14-37 (14-pin DSO with exposed thermal pad) |
| Mounting Type | Surface Mount |
| Automotive Qualification | AEC-Q100 qualified |
| RoHS Compliance | Compliant |
BTS723GWXUMA1 Pin Configuration
| Pin 1 | Vbb β Battery supply voltage (24 V nominal) |
| Pin 2 | IN1 β Input control for channel 1 (CMOS-compatible) |
| Pin 3 | NC β Not connected |
| Pin 4 | IN2 β Input control for channel 2 (CMOS-compatible) |
| Pin 5 | NC β Not connected |
| Pin 6 | NC β Not connected |
| Pin 7 | GND β Logic and power ground |
| Pin 8 | ST β Diagnostic status / fault flag output (current-mirror, shared) |
| Pin 9 | OUT2 β Channel 2 high-side output |
| Pin 10 | OUT2 β Channel 2 high-side output |
| Pin 11 | OUT1 β Channel 1 high-side output |
| Pin 12 | OUT1 β Channel 1 high-side output |
| Pin 13 | OUT1 β Channel 1 high-side output |
| Pin 14 | Vbb β Battery supply voltage (24 V nominal, internally bonded to pin 1) |
Safe Operating Area (SOA) & Thermal Characteristics
No official SOA curve available for this component. Always operate within absolute maximum ratings specified in the datasheet. Ensure adequate cooling and derate as needed.
Typical Applications
BTS723GWXUMA1 is suitable for 6 applications: Automotive Body Control Module (BCM), Dual Automotive Lamp Driver, HVAC Blower and Resistor Switching, Industrial 24 V Load Switching, Power Distribution / Load Multiplexer, 24 V Truck / Commercial-Vehicle Body Electronics.
Automotive Body Control Module (BCM)
The BTS723GWXUMA1 fits the BCM because each channel delivers 2.5 A continuous at 24 V nominal, AEC-Q100 qualification is required, and the PG-DSO-14-37 dual-channel package halves the PCB area vs two single-channel switches. Used to drive interior lamps, mirror heaters, and door-lock solenoids with integrated short-circuit and over-temperature protection, the part withstands ISO 7637-2 transient pulses and 24 V truck battery systems. Its very low Β΅A-level standby current prevents quiescent-drain complaints during long vehicle parking, a critical BCM requirement. Typical wiring places the BTS723GWXUMA1 between the 12 V/24 V Vbb rail and the load, with each output pin direct to a bulb or solenoid return-to-ground.
Recommended
Dual Automotive Lamp Driver
For dual incandescent or LED lamp channels up to 2.5 A each, the BTS723GWXUMA1 provides the high-side switching plus inrush-current protection needed for cold-filament lamps. Its fast demagnetization active clamp handles the inductive kick from relay-driven circuits and turn-indicator loads. Compared with discrete MOSFET plus fuse solutions, the part's diagnostic output reports open-load and short-circuit faults back to the BCM microcontroller, enabling OBD-II compliant bulb-out detection. Per the Classic PROFET datasheet, designers can PWM the input up to several hundred Hz for dimming, though thermal derating applies at high duty cycles.
Recommended
HVAC Blower and Resistor Switching
The BTS723GWXUMA1's 2.5 A continuous rating and 24 V operating window suit HVAC blower-resistor switching and seat-heater control in 12 V and 24 V vehicles. The active Zener clamp absorbs the back-EMF when a DC motor is switched off, protecting the FET from avalanche damage and allowing direct connection to inductive loads without external flyback diodes. With two channels in one package, designers can drive a blower + heater combination from a single IC. The exposed thermal pad of the PG-DSO-14-37 spreads heat between the two output FETs during simultaneous motor-start inrush events.
Recommended
Industrial 24 V Load Switching
Beyond automotive, the BTS723GWXUMA1 is widely used in industrial 24 V PLC and factory-automation I/O modules where two channels of protected high-side switching are required. The CMOS-compatible inputs interface directly with 3.3 V or 5 V microcontrollers, eliminating level-shifters and reducing BOM cost. The AEC-Q100 qualification gives designers extra margin in harsh-environment industrial applications subject to temperature cycling and electrical noise. The PG-DSO-14-37 package plus exposed pad allows direct soldering to standard FR4 boards without heatsinks.
Recommended
Power Distribution / Load Multiplexer
In power-distribution modules the BTS723GWXUMA1 acts as a load multiplexer, switching between two subsystems (e.g., auxiliary lighting and trailer socket) under microcontroller command. Each channel's diagnostic pin reports the actual load state back to the ECU, enabling smart fault recovery without external current-sense amplifiers. The very low standby current prevents battery drain when the vehicle is parked for months. With 2.5 A per channel the part can also drive smaller DC pumps or valve solenoids used in commercial vehicle body electronics.
Recommended
24 V Truck / Commercial-Vehicle Body Electronics
The BTS723GWXUMA1 is rated for 24 V nominal battery systems (trucks, buses, construction equipment) with load-dump survivability to 40 V, making it a direct fit for commercial-vehicle body controllers that must operate from a 24 V battery bus. Two channels per package reduce part count on dense PCBs, while AEC-Q100 qualification and -40 C to +150 C junction range handle under-hood thermal stress. Designers commonly use this part for tail-lamp, marker-lamp, and mirror-fold loads where 24 V supply is mandatory.
Recommended
Recommended Products Summary
Engineering reference data for BTS723GWXUMA1 β comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | BTS723GW | BTS724L2 | BTS721L1 |
|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon |
| Package | PG-DSO-14-37 | PG-DSO-14-37 - same | PG-DSO-14-37 - same | PG-DSO-14-37 - same |
| Number of Channels | 2 | 2 | 2 | 2 |
| Continuous Load Current per Channel | 2.5 A | 2.5 A | 2.5 A | 1.8 A |
| Nominal Operating Voltage (Vbb) | 24 V (6 V to 24 V) | 24 V (6 V to 24 V) | 24 V (6 V to 24 V) | 24 V (6 V to 24 V) |
| Input Logic Level | CMOS-compatible standard | CMOS-compatible standard | Logic-level optimized | CMOS-compatible standard |
| Diagnostic Output | Yes (current-mirror, shared) | Yes (current-mirror, shared) | Yes | Yes |
| Automotive Qualification | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 |
| Tape & Reel Suffix | XUMA1 (2,500 pcs/reel) | Base part (no XUMA1 suffix) | Base part | Base part |
Key Differentiators
- Dual 2.5 A channels in compact PG-DSO-14-37 with very low standby current (vs BTS721L1)
- Identical silicon as BTS723GW base part - guaranteed drop-in (vs BTS723GW)
- AEC-Q100 qualified with 24 V truck load-dump survival (vs BTS724L2)
Design Notes
Estimated: at Vbb = 14 V, I_OUT = 2.5 A per channel, and R_DS(on) β 50 mΞ© (typical for Classic PROFET at 25 Β°C junction), each channel dissipates approximately 0.31 W and both channels together about 0.62 W. With the PG-DSO-14-37 thermal pad soldered to at least 1 cmΒ² of 1 oz copper on FR4, theta_JA stays below 50 K/W and junction rise stays under 31 Β°C above ambient - well within the 150 Β°C maximum. Use larger copper pours or thermal vias if both channels continuously carry the full 2.5 A.
Place a 100 nF ceramic decoupling capacitor as close as possible to the Vbb pins (1 and 14, which are internally bonded). This suppresses voltage transients during fast switching edges of inductive loads and helps the part pass ISO 7637-2 pulse 1 and 2a tests. Keep the Vbb copper pour wide (β₯2 mm) to carry 2.5 A continuous current without significant trace resistance, and route both OUT pins of each channel together to balance current sharing.
Do not exceed the maximum energy rating E_AS during demagnetization of inductive loads. The active Zener clamp typically handles single-pulse avalanche of a few hundred mJ, but continuous PWM switching of large inductors (e.g., relay coils or solenoids) can exceed this. Either add an external free-wheeling diode across the load or limit PWM frequency to keep total E_AS within the datasheet limit. Also respect the -40 Β°C minimum operating temperature; below this, R_DS(on) increases and current capability decreases.
Compliance Information
AEC-Q100 qualified per Infineon product family datasheet (Classic PROFET). RoHS and REACH compliant per manufacturer product page. Halogen-free per Infineon green-product declaration. Conflict-minerals declaration available from Infineon corporate compliance portal.
