Texas Instruments

DP83816AVNG/63SN - 10/100 Ethernet MAC/PHY | TI

MPN: DP83816AVNG/63SN ✓ Active
3.0 V to 3.6 V Vdss 116 mA Id 144-LQFP (20 mm x 20 mm) Package 33 MHz Speed
MOQ: 1 |

DP83816AVNG/63SN Overview

Texas Instruments DP83816AVNG/63SN is a single-chip 10/100 Mb/s Ethernet controller that combines a PCI bus interface, media-access controller, and 10/100BASE-T physical layer in a 144-pin LQFP package measuring 20 mm by 20 mm. It supports a 3.3 V supply range of 3.0 V to 3.6 V, with a typical current draw of 116 mA, and is designed for PCI-compatible host systems, adapter cards, and embedded networking equipment.

An Ethernet MAC/PHY is an integrated interface controller that combines higher-level frame handling with the physical signaling needed for twisted-pair Ethernet. The DP83816 supports the PCI 2.2 bus interface at 33 MHz, allowing packet descriptors and data to move directly between host memory and the controller through bus mastering. This architecture reduces host CPU involvement in Ethernet traffic and supports power-management functions at the system level.

The integrated controller provides 10 Mb/s and 100 Mb/s operation, a 10/100BASE-T network interface, and an IEEE 802.3-compatible physical layer. Its 3.0 V to 3.6 V operating supply and 116 mA typical current draw suit 3.3 V embedded platforms where a separate MAC and Ethernet PHY would add board area and design effort. The 144-LQFP construction also supports a conventional leaded surface-mount assembly process.

The DP83816 targets cost-sensitive, high-volume PC motherboards, PCI network adapter cards, industrial embedded systems, and legacy PCI equipment. Its bus-mastering architecture transfers packet descriptors and payload data without requiring every packet to be copied through a separate host interface controller. Power-management support helps systems coordinate the Ethernet controller with broader platform sleep and wake behavior.

A primary design consideration is the legacy PCI requirement. This controller is appropriate when the host board already provides a compliant 32-bit PCI bus and the required 3.3 V power rails. New designs based on PCIe, USB, or processor-integrated Ethernet interfaces generally require a different controller, so system architecture should be confirmed before component selection.

Place the PHY support network, magnetics interface, decoupling, and PCI routing in accordance with the manufacturer’s reference layout. Differential signal routing should be short and impedance controlled, with a controlled ground plane beneath the high-speed pairs. Power-supply decoupling should be located close to the device to limit transient current paths and reduce susceptibility to conducted noise.

This product page combines the manufacturer’s device description, distributor package and ordering information, verified cross-reference results, and practical selection guidance. It also identifies the limits of direct replacement: the DP83816 family offers the closest documented alternatives, while controllers using different packages or host interfaces are not true drop-in replacements for a 144-pin LQFP PCB footprint.

Drop-in alternatives for DP83816AVNG/63SN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with DP83816AVNG/63SN (same form factor and footprint) — differing in Ethernet Data Rate, Host Interface, Package, Data Transfer Method, PCI Interface Version.

Texas Instruments
Ethernet Data Rate: 10 Mb/s or 100 Mb/s
Host Interface: PCI
Data Transfer Method: Bus mastering
Texas Instruments
Ethernet Data Rate: 10 Mb/s to 100 Mb/s
Host Interface: PCI V2.2 at 33 MHz
Package: 144-pin LQFP, 20 mm x 20 mm

DP83816AVNG

✅ Drop-In
Texas Instruments
📦 144-LQFP (20 mm x 20 mm)
10 Mb/s or 100 Mb/s · IEEE 802.3 · 10/100 Base-T/TX PHY · PCI · 33 MHz · V2.2 · Bus mastering · Flexible receive packet filtration

Contact for price

View Datasheet →

DP83816AVNG/NOPB

✅ Drop-In
Texas Instruments
📦 144-LQFP (20 mm x 20 mm)
10/100 Mb/s integrated PCI Ethernet Media Access Controller and Physical Layer · 10 Mb/s to 100 Mb/s · PCI V2.2 at 33 MHz · 3 V to 3.6 V · 116 mA · 0 °C to +70 °C · 144-pin LQFP, 20 mm x 20 mm · 144 pins

Contact for price

View Datasheet →

DP83816AVNG/EX/NOPB

✅ Drop-In
📦 144-LQFP (20 mm x 20 mm)
Extended ordering suffix with the same DP83816 function and 144-LQFP footprint; qualification and order-code requirements must be checked before substitution

📋 Reference alternative (not in catalog)

DP83816AVNG/63SN Specifications

Device Type 10/100 Mb/s integrated PCI Ethernet media-access controller and physical layer
Ethernet Data Rate 10 Mb/s and 100 Mb/s
Physical Layer Standard IEEE 802.3 10/100BASE-T
Host Interface PCI bus
PCI Interface Version PCI 2.2
PCI Bus Clock 33 MHz
Supply Voltage Range 3.0 V to 3.6 V
Typical Current Draw 116 mA
Bus Mastering Supported
Power Management Support Supported
Package 144-LQFP (20 mm x 20 mm)
Mounting Type Surface Mount
Shipping Format Tape and reel
Ethernet Port Count 1
Integrated PHY Count 1

DP83816AVNG/63SN 144-lqfp (20 mm x 20 mm) Pin Configuration Guide

Pin configuration for DP83816AVNG/63SN (144-lqfp (20 mm x 20 mm) package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

144-lqfp (20 mm x 20 mm) package pinout diagram for DP83816AVNG/63SN

No detailed pinout data available for DP83816AVNG/63SN.

Refer to the datasheet for full pin configuration.

Typical Applications

DP83816AVNG/63SN is suitable for 6 applications: Legacy PCI Network Adapter Cards, Industrial Embedded Ethernet Control, PC Motherboard 10/100 Networking, Legacy PCI Instrumentation Systems, 10/100BASE-T Network Interface Cards, Legacy Computer Communication Bridges.

🌐

Legacy PCI Network Adapter Cards

The DP83816AVNG/63SN fits a PCI adapter that must connect a conventional 32-bit PCI host bus to a 10/100 Mb/s copper Ethernet network. Its integrated MAC and PHY reduce the number of interface components, while PCI 2.2 operation at 33 MHz provides the bus compatibility required by older industrial and embedded platforms. The 144-LQFP footprint also avoids fine-pitch BGA assembly. A production design should preserve the manufacturer’s PCI routing, 3.3 V decoupling, clock, and reset implementation. Ethernet magnetics and controlled differential routing remain required even though the digital MAC and PHY are integrated.

🏭

Industrial Embedded Ethernet Control

The DP83816AVNG/63SN is appropriate for an embedded control system whose backplane exposes a 33 MHz PCI bus and requires 10/100 Mb/s Ethernet communications. A 3.0 V to 3.6 V supply and 116 mA typical current draw align with 3.3 V embedded power architectures. Bus mastering transfers packet descriptors and data directly through DMA, reducing host processing overhead compared with a controller that lacks direct memory access. The legacy PCI requirement is the principal constraint, so verify the carrier-board bus topology, connector pinout, clock source, and reset sequencing before committing the design.

🖥️

PC Motherboard 10/100 Networking

The DP83816AVNG/63SN can implement a basic 10/100 Mb/s Ethernet connection on a PC motherboard or expansion card designed around the PCI 2.2 interface. Combining the host-facing MAC, bus-mastering DMA, and physical layer in one device simplifies the controller section of the board. The manufacturer specifically identifies low-cost, high-volume PC motherboards as a target application. The board still requires an isolated magnetic interface, careful separation of analog and digital return paths, and validated 3.3 V supply decoupling. A PCIe-native design should use a PCIe Ethernet controller instead.

🔧

Legacy PCI Instrumentation Systems

The DP83816AVNG/63SN can add network connectivity to an instrumentation or test system built around an available PCI 2.2 bus. At 10/100 Mb/s, it is suitable for supervisory traffic, configuration transfer, status reporting, and remote-control links that do not require multi-gigabit throughput. The controller’s bus-mastering architecture reduces CPU involvement during packet movement, and its integrated PHY avoids a separate 10/100BASE-T transceiver. Design the network magnetics and isolation barrier for the required environmental isolation, and keep the Ethernet differential route away from high-energy analog and switching nodes.

📡

10/100BASE-T Network Interface Cards

The DP83816AVNG/63SN provides the digital controller and physical-layer functions for a 10/100BASE-T interface card connected through a conventional PCI host bus. It supports both 10 Mb/s and 100 Mb/s operation while maintaining one integrated 3.3 V device in a 144-LQFP package. The board design must include compliant network magnetics, termination, reference-clock and reset arrangements, and carefully controlled differential impedance. For new PCIe systems, this controller is not a direct fit because its parallel PCI interface and host-driver requirements differ from PCIe.

🔗

Legacy Computer Communication Bridges

The DP83816AVNG/63SN can serve as the Ethernet-facing controller in a PCI-based communication bridge that links an older host platform to a 10/100 Mb/s LAN. Its integrated MAC and PHY simplify the communication path, while DMA-based bus mastering allows packet buffers to remain in host memory and reduces per-packet processing overhead. The controller is best suited to systems with a stable 3.3 V rail and an already operational 33 MHz PCI fabric. Firmware and operating-system driver support are as important as electrical compatibility, so validate the host software stack before selecting this legacy-interface device.

What is the DP83816AVNG/63SN?
The DP83816AVNG/63SN is a Texas Instruments single-chip 10/100 Mb/s Ethernet controller with an integrated PCI 2.2 interface and 10/100BASE-T physical layer. According to the manufacturer product page, it is intended for PC motherboards, PCI adapter cards, and embedded systems. The device combines MAC, PHY, and 33 MHz PCI host-interface functions in a 144-pin LQFP package.
What is the operating voltage of DP83816AVNG/63SN?
The DP83816AVNG/63SN operates from 3.0 V to 3.6 V, with a typical current draw of 116 mA. The manufacturer describes it as a 3.3 V Ethernet controller, and the distributor technical listing identifies the same 3.0 V to 3.6 V supply range. This range suits embedded and industrial platforms that already provide a regulated 3.3 V rail.
Where can I download the DP83816AVNG/63SN datasheet PDF?
The official DP83816AVNG/63SN technical documentation is available from the Texas Instruments product page at https://www.ti.com/product/DP83816. The page contains the device description, support materials, and manufacturer documentation links. Use the pin-description table and electrical-characteristics sections when assigning PCB signals, selecting network magnetics, and validating the 3.3 V supply design.
Where can I find the DP83816AVNG/63SN pinout?
The DP83816AVNG/63SN pin assignment is documented in the manufacturer’s DP83816 datasheet, including the 144-LQFP pin-description table. Use that table to identify supply, ground, PCI, clock, reset, and 10/100BASE-T differential signals before routing the PCB. The public listing confirms the 144-LQFP package, while the complete numbered pin list is not reproduced on this page.
Is the DP83816AVNG/63SN a PCI or PCIe device?
The DP83816AVNG/63SN is a conventional PCI controller, not a PCIe device. Texas Instruments specifies implementation of the PCI 2.2 bus interface for host communications at 33 MHz. A board designed around PCIe cannot replace its host interface with this IC without adding substantial bridge and firmware support, even though both technologies can carry Ethernet traffic.
What are the key specifications of DP83816AVNG/63SN that engineers should know?
The principal specifications are a 10/100 Mb/s Ethernet rate, an integrated IEEE 802.3 10/100BASE-T PHY, a PCI 2.2 interface operating at 33 MHz, a 3.0 V to 3.6 V supply range, and a 144-LQFP package. The controller also supports bus mastering and power management. These parameters make it primarily suitable for legacy PCI motherboards, adapter cards, and embedded systems.
What can replace the DP83816AVNG/63SN?
The closest documented drop-in choices are DP83816AVNG and DP83816AVNG/NOPB because they retain the DP83816 function and 144-LQFP footprint. DP83816AVNG/EX/NOPB is another closely related family ordering option. The DP83822IRHBR may offer related Ethernet functionality, but its HRB package is not pin-compatible with the 144-LQFP footprint, so it is not a drop-in replacement.
Is DP83816AVNG the same as DP83816AVNG/63SN?
DP83816AVNG is the base ordering designation for the 144-LQFP DP83816 controller, while DP83816AVNG/63SN identifies a specific ordering and tape-and-reel configuration. The core Ethernet, PCI, voltage, and package characteristics remain the same. Confirm ordering suffixes, temperature grade, reel configuration, and lifecycle requirements against the manufacturer’s current product information.
When should I choose DP83816AVNG/63SN over DP83816AVNG/NOPB?
Choose DP83816AVNG/63SN when the required approved configuration is the /63SN ordering code and tape-and-reel assembly is appropriate for production. Choose DP83816AVNG/NOPB when the no-lead-free order code is required by your procurement specification. Because both are members of the same DP83816 family, electrical and pin compatibility is expected, but the orderable suffixes must still be reconciled before substitution.
Is DP83816AVNG/63SN suitable for embedded systems?
The DP83816AVNG/63SN is suitable for embedded systems that expose a 33 MHz PCI 2.2 bus and use a 3.3 V supply. Its integrated MAC and PHY reduce the component count compared with a separate Ethernet controller and physical layer, while bus mastering allows packet traffic to be transferred through DMA. The key qualification is that the host must already support the legacy PCI interface.
What is the best drop-in replacement for DP83816AVNG/63SN?
DP83816AVNG is the best documented drop-in replacement because it uses the same 144-LQFP DP83816 implementation and preserves the 10/100 Mb/s MAC/PHY and PCI interface. DP83816AVNG/NOPB and DP83816AVNG/EX/NOPB are closely related ordering options. Validate the exact suffix, qualification requirements, pin mapping, and production packing before approving any substitution.
Where can I buy DP83816AVNG/63SN online?
Use the Request a Quote form on this page to request DP83816AVNG/63SN pricing, stock, minimum order quantity, and current lead time. The manufacturer and distributor product links on this page provide identification and technical references, while the quote form supports a current commercial response for the exact 144-LQFP tape-and-reel ordering configuration.
What is the price of DP83816AVNG/63SN?
Current pricing for DP83816AVNG/63SN is obtained through the Request a Quote form on this page because commercial terms and availability can change. The exact part number, 144-LQFP package, and tape-and-reel configuration should be stated in the request to avoid mismatched suffix or packing options. No static price should be used for a production quotation.
What is the lead time and stock status for DP83816AVNG/63SN?
Submit the exact MPN through the Request a Quote form on this page to obtain the current stock position, lead time, and minimum order quantity. The manufacturer targets high-volume and embedded-system applications for this controller, but component inventory varies with ordering suffix and demand. A quote request confirms availability for the production configuration rather than relying on a generic listing.
What design considerations apply to the DP83816AVNG/63SN Ethernet interface?
The design must provide a 3.0 V to 3.6 V rail, a compliant 33 MHz PCI interface, and the manufacturer-specified network magnetics and termination arrangement. Place decoupling capacitors close to their supply pins and route the Ethernet differential pairs as short, impedance-controlled pairs over a continuous ground reference. Follow the manufacturer reference layout for PCI signal integrity, clocking, reset, and exposed test points.

Engineering reference data for DP83816AVNG/63SN — comparison, design guidance, and compliance information.

Selection Guide

Choose DP83816AVNG/63SN for a legacy PCI platform that requires a 10/100 Mb/s copper Ethernet port, an integrated MAC/PHY, and a 144-LQFP footprint. It is especially useful where a 3.3 V supply and 33 MHz PCI bus already exist and bus-mastering DMA can reduce host-processing overhead. Select DP83816AVNG when that base ordering code matches the approved bill of materials, or DP83816AVNG/NOPB when the no-lead-free suffix is required. DP83816AVNG/EX/NOPB is a related ordering option that still requires confirmation of qualification and procurement conditions. Do not select DP83822IRHBR as a PCB drop-in replacement because its HRB package and host-interface requirements differ. For a new PCIe or USB-based product, choose an interface controller designed for that bus rather than forcing this legacy PCI controller into a new architecture.

Comparison with Alternatives

Parameter This Product DP83816AVNG DP83816AVNG/NOPB DP83816AVNG/EX/NOPB
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 144-LQFP (20 mm x 20 mm) 144-LQFP (20 mm x 20 mm) 144-LQFP (20 mm x 20 mm) 144-LQFP (20 mm x 20 mm)
Ethernet Data Rate 10 Mb/s and 100 Mb/s 10 Mb/s and 100 Mb/s 10 Mb/s and 100 Mb/s 10 Mb/s and 100 Mb/s
Host Interface PCI 2.2 at 33 MHz PCI 2.2 at 33 MHz PCI 2.2 at 33 MHz PCI 2.2 at 33 MHz
Integrated Physical Layer IEEE 802.3 10/100BASE-T PHY IEEE 802.3 10/100BASE-T PHY IEEE 802.3 10/100BASE-T PHY IEEE 802.3 10/100BASE-T PHY
Supply Voltage Range 3.0 V to 3.6 V 3.0 V to 3.6 V 3.0 V to 3.6 V 3.0 V to 3.6 V
Typical Current Draw 116 mA 116 mA 116 mA 116 mA
Bus Mastering Supported Supported Supported Supported
Power Management Support Supported Supported Supported Supported
Orderable Suffix /63SN Base ordering code /NOPB /EX/NOPB

Key Differentiators

  • Combines the PCI controller, Ethernet MAC, and 10/100BASE-T PHY (vs DP83822IRHBR)
  • Maintains the legacy PCI 2.2 host interface (vs DP83822IRHBR)
  • Direct same-package family alternatives (vs DP83816AVNG)

Design Notes

Route the Ethernet differential pairs as short, continuous 100-ohm differential paths over a solid ground reference. Keep the PHY-to-magnetics section free of stubs, test pads, and unrelated high-speed traces. Match pair length and spacing according to the manufacturer’s layout guidance, and maintain a controlled separation between the Ethernet domain and switching or analog circuits.

Place all 3.3 V decoupling capacitors close to the corresponding supply and ground pins, with the shortest practical return path through the ground plane. Follow the manufacturer’s recommended capacitor values and layout. Adequate local decoupling limits supply transients when the controller performs DMA transfers and helps prevent Ethernet clock, logic, and PHY functions from being affected by shared supply impedance.

Preserve the manufacturer’s clock, reset, PCI, and signal-termination arrangements when reproducing the reference design. PCI signals require controlled topology and impedance, while the Ethernet differential pairs require continuous reference planes. Avoid placing test fixtures or cable exits in the sensitive differential region. Validate signal integrity and compliance with the complete board, magnetics, enclosure, and intended cable configuration.

Do not treat a related Ethernet controller as a drop-in replacement solely because its data rate is similar. The DP83816AVNG/63SN requires a 144-LQFP footprint and a conventional PCI 2.2 host interface; DP83822IRHBR uses a different package and therefore requires PCB redesign and host-interface changes. Also verify the exact ordering suffix, reel format, operating grade, and driver support before production release.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The DP83816AVNG/NOPB ordering suffix indicates a no-lead-free configuration, but the broader target part’s complete environmental and qualification status is not stated in the cited product information. No RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals claim is inferred.

Related Searches

dp83816avng datasheet dp83816avng nopb DP83816AVNG/63SN datasheet DP83816AVNG/63SN specifications DP83816AVNG/63SN pinout DP83816AVNG/63SN footprint DP83816AVNG/63SN equivalent DP83816AVNG/63SN replacement DP83816AVNG vs DP83822IRHBR DP83816AVNG PCI Ethernet controller DP83816AVNG 144-LQFP DP83816AVNG price Texas Instruments DP83816AVNG

Related Components & Terms

Texas Instruments DP83816AVNG/63SN DP83816AVNG DP83816AVNG/NOPB DP83816AVNG/EX/NOPB DP83822IRHBR Ethernet controller Ethernet MAC Ethernet PHY 10/100BASE-T IEEE 802.3 PCI 2.2 33 MHz PCI bus bus mastering direct memory access power management 144-LQFP LQFP package family surface-mount package 3.3 V power supply 116 mA typical current 10 Mb/s Ethernet 100 Mb/s Ethernet embedded networking PCI adapter card
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details