DP83816AVNG/63SN - 10/100 Ethernet MAC/PHY | TI
MPN: DP83816AVNG/63SN ✓ פעילDP83816AVNG/63SN סקירה
An Ethernet MAC/PHY is an integrated interface controller that combines higher-level frame handling with the physical signaling needed for twisted-pair Ethernet. The DP83816 supports the PCI 2.2 bus interface at 33 MHz, allowing packet descriptors and data to move directly between host memory and the controller through bus mastering. This architecture reduces host CPU involvement in Ethernet traffic and supports power-management functions at the system level.
The integrated controller provides 10 Mb/s and 100 Mb/s operation, a 10/100BASE-T network interface, and an IEEE 802.3-compatible physical layer. Its 3.0 V to 3.6 V operating supply and 116 mA typical current draw suit 3.3 V embedded platforms where a separate MAC and Ethernet PHY would add board area and design effort. The 144-LQFP construction also supports a conventional leaded surface-mount assembly process.
The DP83816 targets cost-sensitive, high-volume PC motherboards, PCI network adapter cards, industrial embedded systems, and legacy PCI equipment. Its bus-mastering architecture transfers packet descriptors and payload data without requiring every packet to be copied through a separate host interface controller. Power-management support helps systems coordinate the Ethernet controller with broader platform sleep and wake behavior.
A primary design consideration is the legacy PCI requirement. This controller is appropriate when the host board already provides a compliant 32-bit PCI bus and the required 3.3 V power rails. New designs based on PCIe, USB, or processor-integrated Ethernet interfaces generally require a different controller, so system architecture should be confirmed before component selection.
Place the PHY support network, magnetics interface, decoupling, and PCI routing in accordance with the manufacturer’s reference layout. Differential signal routing should be short and impedance controlled, with a controlled ground plane beneath the high-speed pairs. Power-supply decoupling should be located close to the device to limit transient current paths and reduce susceptibility to conducted noise.
This product page combines the manufacturer’s device description, distributor package and ordering information, verified cross-reference results, and practical selection guidance. It also identifies the limits of direct replacement: the DP83816 family offers the closest documented alternatives, while controllers using different packages or host interfaces are not true drop-in replacements for a 144-pin LQFP PCB footprint.
חלופות תחליף ישיר עבור DP83816AVNG/63SN — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DP83816AVNG/63SN (אותו גורם צורה וטביעת רגל) — שונים ב Ethernet Data Rate, Host Interface, Package, Data Transfer Method, PCI Interface Version.
DP83816AVNG
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DP83816AVNG/NOPB
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DP83816AVNG/EX/NOPB
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DP83816AVNG/63SN מפרטים
| Device Type | 10/100 Mb/s integrated PCI Ethernet media-access controller and physical layer |
| Ethernet Data Rate | 10 Mb/s and 100 Mb/s |
| Physical Layer Standard | IEEE 802.3 10/100BASE-T |
| Host Interface | PCI bus |
| PCI Interface Version | PCI 2.2 |
| PCI Bus Clock | 33 MHz |
| Supply Voltage Range | 3.0 V to 3.6 V |
| Typical Current Draw | 116 mA |
| Bus Mastering | Supported |
| Power Management Support | Supported |
| מארז | 144-LQFP (20 mm x 20 mm) |
| סוג הרכבה | Surface Mount |
| Shipping Format | Tape and reel |
| Ethernet Port Count | 1 |
| Integrated PHY Count | 1 |
מדריך תצורת פינים של DP83816AVNG/63SN 144-lqfp (20 mm x 20 mm)
תצורת פינים עבור DP83816AVNG/63SN (מארזת 144-lqfp (20 mm x 20 mm)). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור DP83816AVNG/63SN.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
DP83816AVNG/63SN מתאים עבור 6 יישוםs: Legacy PCI Network Adapter Cards, Industrial Embedded Ethernet Control, PC Motherboard 10/100 Networking, Legacy PCI Instrumentation Systems, 10/100BASE-T Network Interface Cards, Legacy Computer Communication Bridges.
Legacy PCI Network Adapter Cards
The DP83816AVNG/63SN fits a PCI adapter that must connect a conventional 32-bit PCI host bus to a 10/100 Mb/s copper Ethernet network. Its integrated MAC and PHY reduce the number of interface components, while PCI 2.2 operation at 33 MHz provides the bus compatibility required by older industrial and embedded platforms. The 144-LQFP footprint also avoids fine-pitch BGA assembly. A production design should preserve the manufacturer’s PCI routing, 3.3 V decoupling, clock, and reset implementation. Ethernet magnetics and controlled differential routing remain required even though the digital MAC and PHY are integrated.
מומלץ
Industrial Embedded Ethernet Control
The DP83816AVNG/63SN is appropriate for an embedded control system whose backplane exposes a 33 MHz PCI bus and requires 10/100 Mb/s Ethernet communications. A 3.0 V to 3.6 V supply and 116 mA typical current draw align with 3.3 V embedded power architectures. Bus mastering transfers packet descriptors and data directly through DMA, reducing host processing overhead compared with a controller that lacks direct memory access. The legacy PCI requirement is the principal constraint, so verify the carrier-board bus topology, connector pinout, clock source, and reset sequencing before committing the design.
מומלץ
PC Motherboard 10/100 Networking
The DP83816AVNG/63SN can implement a basic 10/100 Mb/s Ethernet connection on a PC motherboard or expansion card designed around the PCI 2.2 interface. Combining the host-facing MAC, bus-mastering DMA, and physical layer in one device simplifies the controller section of the board. The manufacturer specifically identifies low-cost, high-volume PC motherboards as a target application. The board still requires an isolated magnetic interface, careful separation of analog and digital return paths, and validated 3.3 V supply decoupling. A PCIe-native design should use a PCIe Ethernet controller instead.
מומלץ
Legacy PCI Instrumentation Systems
The DP83816AVNG/63SN can add network connectivity to an instrumentation or test system built around an available PCI 2.2 bus. At 10/100 Mb/s, it is suitable for supervisory traffic, configuration transfer, status reporting, and remote-control links that do not require multi-gigabit throughput. The controller’s bus-mastering architecture reduces CPU involvement during packet movement, and its integrated PHY avoids a separate 10/100BASE-T transceiver. Design the network magnetics and isolation barrier for the required environmental isolation, and keep the Ethernet differential route away from high-energy analog and switching nodes.
מומלץ
10/100BASE-T Network Interface Cards
The DP83816AVNG/63SN provides the digital controller and physical-layer functions for a 10/100BASE-T interface card connected through a conventional PCI host bus. It supports both 10 Mb/s and 100 Mb/s operation while maintaining one integrated 3.3 V device in a 144-LQFP package. The board design must include compliant network magnetics, termination, reference-clock and reset arrangements, and carefully controlled differential impedance. For new PCIe systems, this controller is not a direct fit because its parallel PCI interface and host-driver requirements differ from PCIe.
מומלץ
Legacy Computer Communication Bridges
The DP83816AVNG/63SN can serve as the Ethernet-facing controller in a PCI-based communication bridge that links an older host platform to a 10/100 Mb/s LAN. Its integrated MAC and PHY simplify the communication path, while DMA-based bus mastering allows packet buffers to remain in host memory and reduces per-packet processing overhead. The controller is best suited to systems with a stable 3.3 V rail and an already operational 33 MHz PCI fabric. Firmware and operating-system driver support are as important as electrical compatibility, so validate the host software stack before selecting this legacy-interface device.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DP83816AVNG/63SN — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DP83816AVNG | DP83816AVNG/NOPB | DP83816AVNG/EX/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 144-LQFP (20 mm x 20 mm) | 144-LQFP (20 mm x 20 mm) | 144-LQFP (20 mm x 20 mm) | 144-LQFP (20 mm x 20 mm) |
| Ethernet Data Rate | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s |
| Host Interface | PCI 2.2 at 33 MHz | PCI 2.2 at 33 MHz | PCI 2.2 at 33 MHz | PCI 2.2 at 33 MHz |
| Integrated Physical Layer | IEEE 802.3 10/100BASE-T PHY | IEEE 802.3 10/100BASE-T PHY | IEEE 802.3 10/100BASE-T PHY | IEEE 802.3 10/100BASE-T PHY |
| Supply Voltage Range | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Typical Current Draw | 116 mA | 116 mA | 116 mA | 116 mA |
| Bus Mastering | Supported | Supported | Supported | Supported |
| Power Management Support | Supported | Supported | Supported | Supported |
| Orderable Suffix | /63SN | Base ordering code | /NOPB | /EX/NOPB |
מבדילים עיקריים
- Combines the PCI controller, Ethernet MAC, and 10/100BASE-T PHY (לעומתDP83822IRHBR)
- Maintains the legacy PCI 2.2 host interface (לעומתDP83822IRHBR)
- Direct same-package family alternatives (לעומתDP83816AVNG)
הערות תכנון
Route the Ethernet differential pairs as short, continuous 100-ohm differential paths over a solid ground reference. Keep the PHY-to-magnetics section free of stubs, test pads, and unrelated high-speed traces. Match pair length and spacing according to the manufacturer’s layout guidance, and maintain a controlled separation between the Ethernet domain and switching or analog circuits.
Place all 3.3 V decoupling capacitors close to the corresponding supply and ground pins, with the shortest practical return path through the ground plane. Follow the manufacturer’s recommended capacitor values and layout. Adequate local decoupling limits supply transients when the controller performs DMA transfers and helps prevent Ethernet clock, logic, and PHY functions from being affected by shared supply impedance.
Preserve the manufacturer’s clock, reset, PCI, and signal-termination arrangements when reproducing the reference design. PCI signals require controlled topology and impedance, while the Ethernet differential pairs require continuous reference planes. Avoid placing test fixtures or cable exits in the sensitive differential region. Validate signal integrity and compliance with the complete board, magnetics, enclosure, and intended cable configuration.
Do not treat a related Ethernet controller as a drop-in replacement solely because its data rate is similar. The DP83816AVNG/63SN requires a 144-LQFP footprint and a conventional PCI 2.2 host interface; DP83822IRHBR uses a different package and therefore requires PCB redesign and host-interface changes. Also verify the exact ordering suffix, reel format, operating grade, and driver support before production release.
מידע על תאימות
The DP83816AVNG/NOPB ordering suffix indicates a no-lead-free configuration, but the broader target part’s complete environmental and qualification status is not stated in the cited product information. No RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals claim is inferred.