Texas Instruments

DS90CR215MTD - 21-Bit 66MHz LVDS Transmitter | Texas Instruments

MPN: DS90CR215MTD ✓ Active
3.3 V Vdss 48-TSSOP Package 66 MHz Speed
MOQ: 1 |

DS90CR215MTD Overview

The Texas Instruments DS90CR215MTD is a 3.3 V, rising-edge data-strobe LVDS transmitter for parallel-to-serial data transfer, supporting 21 bits at up to 66 MHz in a 48-TSSOP package. The device is intended for point-to-point links that require low-voltage differential signaling, a dedicated clock strobe, and compact digital-interface conversion.

An LVDS transmitter, also called an LVDS driver, converts low-voltage digital signals into a balanced differential pair. This differential signaling method improves noise immunity by rejecting common-mode noise and allowing the receiver to detect smaller voltage differences. In the DS90CR215, the data-strobe architecture carries 21 data bits together with a clock signal, placing the transmitter within the parallel-interface and serial-link hierarchy of communication ICs.

Principal characteristics include 3.3 V operation, 21-bit parallel data handling, a 66 MHz maximum signaling rate, and a 48-TSSOP package. The manufacturer identifies the device as a rising-edge data-strobe LVDS interface IC. Its operating temperature range extends from -40 °C to +85 °C, supporting industrial-temperature equipment. The package is intended for surface-mount assembly and provides a relatively high pin count for the parallel data and differential output connections.

The DS90CR215MTD is designed for systems in which a processor, FPGA, display controller, or data acquisition engine must communicate over a fast, noise-resistant differential link. Because the link uses balanced signaling, it can operate in environments containing switching equipment, long internal cable runs, or multiple high-speed digital sources where single-ended routing would be more susceptible to interference.

Typical uses include industrial control cabinets, test and measurement systems, medical monitoring equipment, instrumentation, video-processing modules, and embedded data acquisition. The 66 MHz channel-link rate supports high-throughput point-to-point transfers, while the 21-bit parallel interface reduces the number of package pins required for data compared with a fully serialized interface. Matching receiver characteristics and controlled trace geometry remain important for reliable operation.

For PCB design, treat the differential data and clock outputs as controlled-impedance nets, place the device close to the connector or receiving interface, and route the differential pair as a matched pair without plane splits or excessive stubs. Verify power and ground distribution, follow the manufacturer's decoupling recommendations, and confirm that the receiver and cable meet the link's timing and termination requirements.

This page consolidates the manufacturer's product characteristics, package information, operating limits, sourcing links, and practical interface guidance into one engineering reference. It also highlights the limited availability of verified pin-compatible substitutes and distinguishes exact lead-finish variants from parts that cannot replace the transmitter function.

Drop-in alternatives for DS90CR215MTD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

DS90CR215MTD/NOPB

✅ Drop-In
📦 48-TSSOP
Same 21-bit, 66 MHz LVDS transmitter family and 48-TSSOP footprint; the NOPB suffix identifies the no-lead finish, with no stated change to the principal electrical ratings.

📋 Reference alternative (not in catalog)

DS90CR215MTD Specifications

Product Type LVDS rising-edge data-strobe transmitter
Supply Voltage 3.3 V
Parallel Data Width 21 bits
Maximum Clock Frequency 66 MHz
Signal Type LVDS differential signaling
Data-Strobe Edge Rising edge
Package 48-TSSOP
Mounting Type Surface mount
Operating Temperature Range -40 °C to +85 °C
Product Category Interface IC

DS90CR215MTD 48-tssop Pin Configuration Guide

Pin configuration for DS90CR215MTD (48-tssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

48-tssop package pinout diagram for DS90CR215MTD

No detailed pinout data available for DS90CR215MTD.

Refer to the datasheet for full pin configuration.

Typical Applications

DS90CR215MTD is suitable for 6 applications: FPGA-to-FPGA Board-Level Data Link, Industrial Control Cabinet Data Transfer, Data Acquisition and Instrumentation, Medical Monitoring Equipment, Video Processing Module Interconnect, Test and Measurement Equipment.

🖥️

FPGA-to-FPGA Board-Level Data Link

The DS90CR215MTD suits high-speed transfers between FPGA-based modules because it accepts a 21-bit parallel data-strobe bus and converts it into LVDS differential signaling at up to 66 MHz. Differential outputs improve common-mode noise rejection on long routed pairs and reduce radiated emissions compared with many single-ended implementations. Place the transmitter close to the receiving FPGA, route data and strobe pairs with matched geometry, and maintain a continuous reference plane. The design must still account for clock-to-data skew, receiver setup and hold requirements, and the loss introduced by connectors or an inter-board cable.

🏭

Industrial Control Cabinet Data Transfer

The DS90CR215MTD is appropriate for transferring control and status data between industrial modules when the board environment contains switching converters and relay drive circuitry. Its 21-bit parallel input reduces the number of single-ended nets crossing a noisy enclosure boundary, while the LVDS outputs provide a balanced signal that rejects common-mode disturbance. The -40 °C to +85 °C operating range supports industrial-temperature installations. Validate EMC performance with the final receiver, cable, connector, and enclosure because compliance depends on the assembled product rather than the transmitter alone.

📟

Data Acquisition and Instrumentation

The DS90CR215MTD can carry a dense 21-bit measurement bus from an acquisition front end to a processing module at a 66 MHz clock rate. Balanced LVDS signaling helps preserve data integrity in instrument enclosures that contain switching regulators, amplifiers, and long inter-board connections. The transmitter is best placed adjacent to the receiver so that only the intended differential link traverses the noisy environment. Designers should verify converter settling time, analog-to-digital converter latency, clock distribution, and channel skew before treating the link as transparent to the source data.

💊

Medical Monitoring Equipment

The DS90CR215MTD may be used inside medical monitoring equipment to transfer sampled data from a processing board to a display, storage module, or remote interface. The differential link can reduce susceptibility to interference compared with a wide single-ended bus, while the 21-bit width and 66 MHz rate accommodate dense digital traffic. The device's industrial temperature range does not itself establish medical-product compliance. Confirmation of electrical safety, EMC, risk management, and system validation remains the responsibility of the finished equipment designer.

📺

Video Processing Module Interconnect

The DS90CR215MTD fits point-to-point video-processing interconnects where parallel pixel, control, or configuration data must cross a board boundary at up to 66 MHz. Its 21-bit parallel-to-LVDS conversion reduces the number of package pins needed for wide parallel traffic and provides a balanced output that behaves predictably in a multilayer PCB. Use the receiver's timing specification to define the allowable clock-to-data skew, and keep video and power-distribution regions separated. Cable-based implementations also require connector, cable, and receiver termination validation.

🧪

Test and Measurement Equipment

The DS90CR215MTD is useful in test and measurement instruments that move acquisition results, calibration tables, or instrument-control data between high-speed modules. Differential signaling at up to 66 MHz reduces sensitivity to ground offsets and radiated noise commonly found near switching power supplies. Position the transmitter near the receiver and receiver termination to minimize signal loss and maintain timing margin. For laboratory-grade accuracy, separately evaluate analog reference noise, clock jitter, and data-converter aperture requirements because the LVDS link itself does not improve source accuracy.

What is the DS90CR215MTD?
The DS90CR215MTD is a Texas Instruments 3.3 V LVDS transmitter that converts a 21-bit parallel data-strobe interface into differential serial signals operating at up to 66 MHz. The manufacturer lists it in a 48-TSSOP package for surface-mount assembly. According to the TI product page, its defining characteristics are the 21-bit width, rising-edge data-strobe operation, and 66 MHz maximum signaling frequency.
What are the key specifications of DS90CR215MTD that engineers should know?
The DS90CR215MTD combines a 3.3 V supply, 21-bit parallel data handling, 66 MHz maximum clock operation, rising-edge data-strobe architecture, and a 48-TSSOP package. Its -40 °C to +85 °C operating range covers industrial-temperature equipment. These figures identify the part as a dedicated LVDS parallel-to-serial interface IC rather than a general-purpose logic or memory device.
What is the DS90CR215MTD used for?
The DS90CR215MTD is used for high-speed point-to-point LVDS links carrying 21 data bits plus a clock strobe. Common implementations connect an FPGA, processor, data-acquisition engine, display controller, or industrial controller to a receiver across a board connection or short cable run. Differential outputs improve common-mode noise rejection compared with single-ended signaling in electrically noisy systems.
How does the DS90CR215MTD differ from DS90CR215MTD/NOPB?
The DS90CR215MTD/NOPB is a no-lead-finish ordering variant of the same Texas Instruments LVDS transmitter family. The available product listings identify both versions as 3.3 V, 21-bit, 66 MHz rising-edge data-strobe LVDS devices in 48-TSSOP packages. Confirm the exact orderable suffix, termination marking, and packaging requirements before substituting one suffix for the other.
What is the difference between DS90CR215MTD and DS90CR216MTD?
DS90CR215MTD is the transmitter in the 21-bit, 66 MHz rising-edge Channel Link family, while DS90CR216 is the companion receiver function. The two devices occupy different ends of a differential link and are therefore complementary rather than interchangeable. A system requires a DS90CR215-class transmitter at the source and a DS90CR216-class receiver at the destination.
Can DS90CR216MTD replace DS90CR215MTD?
No. A DS90CR216-family receiver cannot replace the DS90CR215MTD transmitter even if its package options overlap, because the receiver and transmitter have different circuit roles, input structures, and output interfaces. The transmitter accepts parallel data and generates differential LVDS outputs; the receiver accepts differential LVDS inputs and reconstructs parallel data. Treat the two parts as the two ends of one link.
When should I choose DS90CR215MTD over a single-ended parallel interface?
Choose the DS90CR215MTD when the link must carry 21 data bits plus a clock across a board or cable connection in an environment where single-ended routing could be exposed to noise. Its differential outputs reject common-mode disturbance and can support a 66 MHz clock rate. For short, quiet, board-contained links, a plain CMOS interface may be simpler if its timing and noise margins are acceptable.
Is DS90CR215MTD suitable for industrial control systems?
The DS90CR215MTD is suitable for many industrial-temperature systems because its specified operating range is -40 °C to +85 °C. It is also appropriate for point-to-point transfers between control logic, FPGA-based modules, and data acquisition equipment. Final suitability depends on the complete system's EMC requirements, enclosure, cable length, receiver characteristics, and regulatory testing.
Where can I download the DS90CR215MTD datasheet PDF?
The official DS90CR215 datasheet is available through the Texas Instruments product-page download link at https://www.ti.com/lit/gpn/DS90CR215. The document covers the DS90CR215 and DS90CR216 family and provides the authoritative information for pin assignments, electrical characteristics, timing, applications, and recommended layouts.
Where can I find the DS90CR215MTD pinout?
The DS90CR215MTD pinout is defined in the pin-configuration section of the manufacturer datasheet for the DS90CR215/DS90CR216 family. The device uses a 48-TSSOP package, so the datasheet pin table should be matched directly to the physical symbol and board footprint. Use that table rather than inferring connections from the distributor listing.
How should DS90CR215MTD LVDS traces be routed on a PCB?
Route each LVDS pair as a tightly coupled, length-matched differential pair with continuous reference planes and no intervening plane splits. Place the transmitter close to the connector or receiving device, avoid long stubs, and follow the manufacturer's recommended input, output, and bypass-capacitor arrangements. The required trace impedance and connector or receiver termination must be determined from the complete link design.
What is the best drop-in replacement for DS90CR215MTD?
The closest verified ordering alternative is DS90CR215MTD/NOPB, which appears in the retrieved product listings for the same 48-TSSOP LVDS transmitter family. No other manufacturer part was confirmed as a pin-to-pin drop-in replacement with equivalent 21-bit, 66 MHz transmitter behavior. Request a formal manufacturer cross-reference before adopting any substitute or changing the transceiver function.
What can replace DS90CR215MTD?
DS90CR215MTD/NOPB is the only directly identified ordering alternative for the DS90CR215MTD in the retrieved product information. It represents the no-lead-finish version of the same transmitter family rather than a third-party substitute. If that suffix is unsuitable, verify a replacement through the manufacturer's cross-reference search and compare every pin, voltage rating, timing parameter, and termination requirement.
Where can I buy DS90CR215MTD online?
The DS90CR215MTD can be requested through the Request a Quote form on this page, where current unit availability, volume pricing, and delivery can be reviewed for your order. The manufacturer's product page and the listed distribution pages provide additional part identification and documentation. XAIPART does not present static price figures because quotation and stock conditions can change.
What is the price of DS90CR215MTD?
The current price of DS90CR215MTD depends on order quantity, package suffix, inventory, and the purchasing channel. Use the Request a Quote form on this page to request current volume pricing and availability for your specific configuration. This page does not publish a static price because marketplace values can change independently of the component's technical specification.
What is the lead time and stock status of DS90CR215MTD?
Current lead time and stock status for DS90CR215MTD should be confirmed through the Request a Quote form on this page. Availability can differ between the base MTD ordering code and the MTD/NOPB lead-finish variant, and distributor inventory changes independently. Provide your required quantity, target date, and acceptable suffix when requesting a quotation.

Engineering reference data for DS90CR215MTD — comparison, design guidance, and compliance information.

Selection Guide

Choose the DS90CR215MTD when a system needs a 21-bit parallel data-strobe input converted into balanced LVDS outputs at up to 66 MHz. It is particularly useful on board-to-board and short-cable links where common-mode noise, ground differences, or connector routing could compromise a single-ended interface. The DS90CR215MTD/NOPB is the directly identified alternative when the no-lead-finish ordering code is required and the remaining ordering conditions are acceptable. Do not select a DS90CR216-family receiver as a transmitter substitute even if a matching package option appears in a search result. If a different manufacturer or protocol is required, first confirm identical pin mapping, 21-bit or equivalent payload handling, at least 66 MHz operation, 3.3 V compatibility, and equivalent LVDS output levels. For designs requiring different payload widths or clock rates, use a dedicated Channel Link part selected from the complete TI interface family rather than forcing an electrical substitution.

Comparison with Alternatives

Parameter This Product DS90CR215MTD/NOPB
Package 48-TSSOP 48-TSSOP - same package
Brand Texas Instruments Texas Instruments
Product Function Rising-edge data-strobe LVDS transmitter Rising-edge data-strobe LVDS transmitter
Supply Voltage 3.3 V 3.3 V
Data Width 21 bits 21 bits
Maximum Clock Frequency 66 MHz 66 MHz
Output Signaling LVDS differential LVDS differential
Data-Strobe Edge Rising edge Rising edge

Key Differentiators

  • Exact verified ordering alternative (vs DS90CR215MTD/NOPB)
  • Dedicated parallel-to-LVDS transmitter function (vs DS90CR216 family)
  • Wide parallel payload in a compact interface package (vs Narrower Channel Link interface options)

Design Notes

Route every LVDS data and strobe pair as a coupled differential pair over a continuous reference plane. Keep the pair spacing and trace width consistent with the required characteristic impedance, avoid plane splits beneath the links, and remove unnecessary stubs. Place the transmitter close to the receiving device or connector so that only the required signal travels through the higher-noise region of the PCB.

Use the DS90CR215/DS90CR216 datasheet timing diagrams to establish clock-to-data skew and setup-and-hold margins across the complete link. Account for connector and cable delay as well as PCB propagation delay. When the link crosses a cable assembly, verify the receiver termination, cable impedance, and loss rather than assuming that the transmitter's differential outputs alone guarantee reliable operation.

Place bypass capacitors close to the device's supply and ground connections and follow the pin-specific arrangement shown in the manufacturer datasheet. Provide a return path that does not force high-frequency differential return current through a split or narrowed plane. If the link transmitter shares a board with switching regulators or relays, separate their current paths and verify the supply ripple at the device pins with an oscilloscope.

Do not substitute the companion DS90CR216 receiver for the DS90CR215 transmitter, and do not assume a shared package guarantees interchangeable function. Confirm that every candidate has the same transmitter role, data width, clock-rate rating, supply requirements, pin mapping, and output interface. Also verify the exact MTD ordering suffix because NOPB identifies a lead-finish option rather than a new protocol configuration.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The retrieved listings identify a separate MTD/NOPB ordering option but do not explicitly state this part's RoHS, REACH, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not applicable to this general-purpose interface IC because no automotive qualification was identified.

Data verified on: 2026-11-10 — data verified and curated by XAIPART's component engineering team

Related Searches

ds90cr215mtd nopb DS90CR215MTD datasheet DS90CR215MTD pinout DS90CR215MTD datasheet pdf Texas Instruments DS90CR215MTD DS90CR215 21-bit LVDS transmitter DS90CR215 66MHz interface IC DS90CR215MTD 48-TSSOP pinout DS90CR215MTD drop-in replacement DS90CR215MTD equivalent DS90CR215MTD vs DS90CR216 DS90CR215MTD FPGA data link DS90CR215MTD price DS90CR215MTD stock

Related Components & Terms

Texas Instruments DS90CR215MTD DS90CR215MTD/NOPB DS90CR216 DS90CR213MTD DS90CF562MTD LVDS transmitter LVDS receiver low-voltage differential signaling data strobe rising-edge interface parallel-to-serial interface Channel Link 21-bit parallel bus 66 MHz clock 3.3 V power supply 48-TSSOP package surface-mount package industrial temperature range common-mode noise rejection differential pair routing FPGA data transfer industrial control systems data acquisition RoHS REACH
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details