Texas Instruments

DS90CR287MTD - 85MHz 28-Bit LVDS Transmitter | Texas Instruments

MPN: DS90CR287MTD ✓ Active
+3.3 V Vdss 56-pin TSSOP Package 85 MHz Speed
MOQ: 1 |

DS90CR287MTD Overview

The Texas Instruments DS90CR287MTD is a +3.3 V rising-edge data-strobe LVDS 28-bit Channel Link transmitter with an 85 MHz operating frequency, four LVDS data outputs plus a transmitted clock, and a 56-pin TSSOP package. It converts 28 parallel LVCMOS/LVTTL input bits into four differential LVDS data streams while forwarding a phase-locked transmit clock on a fifth LVDS link.

A Channel Link transmitter is a high-speed parallel-to-differential interface IC used to move multiple data bits across a cable or PCB interconnect. The DS90CR287 belongs to the LVDS interface IC hierarchy, which includes differential line drivers, channel-link serializers, clock transmitters, and receiver counterparts. Its parallel-to-LVDS architecture reduces the number of signal conductors required for wide data transfers while supporting reliable clocking across that link.

The principal features include 28 LVCMOS/LVTTL data inputs, four LVDS data streams, a fifth differential clock output, an 85 MHz operating frequency, and operation from a +3.3 V supply. The transmitter is intended for rising-edge data-strobe applications and supports an industrial temperature range of -10°C to +70°C. A 56-pin TSSOP provides adequate routing density for the wide parallel input interface and five differential outputs.

Technically, the device serializes each cycle of the transmit clock into four differential data lanes. The transmitted clock provides a source-synchronous reference at the receiver, allowing the receiving system to capture the data relative to the forwarded clock. This architecture is useful when the source and destination must exchange parallel data across a limited number of high-speed conductors while retaining deterministic timing.

Typical applications include industrial imaging equipment, video transport systems, data-acquisition modules, digital cameras, test and measurement instruments, and industrial control panels. The 28-bit parallel input and multi-lane LVDS output can reduce connector pin count compared with driving every parallel bit as a single-ended signal, especially in space-constrained equipment.

The key design consideration is that the LVDS link still requires controlled impedance, short stubs, suitable connectors, and compliant differential routing. Input and output timing, cable length, connector behavior, and receiver capability determine whether the full 85 MHz operating rate is practical in a specific system.

This product page organizes the DS90CR287MTD interface details, verified source links, replacement analysis, and application guidance into a design-focused reference for engineers evaluating parallel-to-LVDS data links.

Drop-in alternatives for DS90CR287MTD — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with DS90CR287MTD (same form factor and footprint) — differing in Package, Supply Voltage.

Texas Instruments
Package: 56-TSSOP
Supply Voltage: 3.3 V
Compare with DS90CR287MTD →

DS90CR287MTD/NOPB

✅ Drop-In
📦 56-pin TSSOP
Same 56-pin TSSOP, terminals, and principal performance characteristics; 0% difference in the documented core interface ratings

📋 Reference alternative (not in catalog)

DS90CR287MTDX/NOPB

✅ Drop-In
📦 56-pin TSSOP
Same 56-pin TSSOP and -10°C to +70°C rating; 0% difference in the documented operating range

📋 Reference alternative (not in catalog)

DS90CR287MTD/NOPB

✅ Drop-In
📦 56-pin TSSOP
Same 56-pin TSSOP, +3.3 V supply, 85 MHz clock, and 28-bit interface; 0% difference in the documented headline ratings

📋 Reference alternative (not in catalog)

DS90CR287MTD Specifications

Product Type LVDS 28-bit Channel Link transmitter
Supply Voltage +3.3 V
Operating Frequency 85 MHz
Data Input Width 28 bits
Input Logic LVCMOS/LVTTL
LVDS Data Outputs 4 differential data streams
Clock Output 1 differential LVDS transmit-clock stream
Data Transfer Edge Rising edge
Package 56-pin TSSOP
Mounting Type Surface mount
Operating Temperature -10°C to +70°C
Output Differential Voltage 0.45 V
Data Rate 2380 Mbps

DS90CR287MTD 56-pin tssop Pin Configuration Guide

Pin configuration for DS90CR287MTD (56-pin tssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

56-pin tssop package pinout diagram for DS90CR287MTD

No detailed pinout data available for DS90CR287MTD.

Refer to the datasheet for full pin configuration.

Typical Applications

DS90CR287MTD is suitable for 6 applications: Industrial Camera Data Transport, Digital Video Transport, Data Acquisition Systems, Test and Measurement Equipment, Industrial Control Panels, Medical Imaging Interfaces.

📷

Industrial Camera Data Transport

The DS90CR287MTD fits parallel-output image sensors and industrial cameras that need to transfer 28 data bits per clock without allocating one connector conductor for every LVCMOS bit. Its four LVDS data lanes plus transmitted clock reduce the link width while preserving a source-synchronous 85 MHz operating rate. Designers should match the receiver to the 28-bit frame and clock timing, then validate differential routing, connector loss, and cable length under the intended temperature conditions.

📺

Digital Video Transport

The DS90CR287MTD can carry wide parallel video or pixel data across a compact LVDS connection by converting 28 LVCMOS/LVTTL bits into four differential data streams and one transmitted clock. At 85 MHz, the documented aggregate rate is 2380 Mbps, which is useful for transporting parallel raster or frame data inside industrial monitoring equipment. The implementation depends on receiver timing tolerance, LVDS pair routing, and a connector and cable characterized for the target transfer distance.

📊

Data Acquisition Systems

For multi-channel data-acquisition and control systems, the DS90CR287MTD provides a parallel-to-differential transition between an FPGA or processor bus and a remote receiver card. Its 28 input bits can represent counters, status flags, samples, or timestamp data, while the phase-locked transmit clock supports deterministic capture at the destination. PCB implementation should preserve LVDS impedance and pair symmetry, minimize stubs, and confirm that the downstream receiver supports the same 85 MHz data-strobe protocol.

🧰

Test and Measurement Equipment

The DS90CR287MTD is useful in test and measurement instruments that move wide parallel result or control data between circuit boards while limiting cable count. The +3.3 V operation, 85 MHz Channel Link rate, and transmitted differential clock suit source-synchronous backplane or cable links requiring repeatable timing. For bench equipment, qualify the complete interconnect including cables, connectors, and receiver loading, and check the -10°C to +70°C range against the enclosure temperature.

🏭

Industrial Control Panels

The DS90CR287MTD can bridge a control module and display or processing electronics by transporting 28 command and status bits over four LVDS data pairs and one clock pair. The reduced conductor count can simplify high-density backplane or cable assemblies compared with parallel single-ended routing. Engineers should treat the transmitted clock and receiver capture timing as a matched interface, maintain controlled differential impedance, and verify cable length and temperature performance before production release.

💊

Medical Imaging Interfaces

The DS90CR287MTD can support high-density image or control-data transfer in medical imaging equipment where a 28-bit parallel source must be serialized onto differential lanes. The 85 MHz rate allows wide data movement with five differential outputs, including the transmitted clock used for source-synchronous capture. Any medical use requires system-level validation of receiver compatibility, signal integrity, electrical isolation requirements, and applicable sector-specific quality procedures beyond the component's stated temperature range.

What is the DS90CR287MTD?
The DS90CR287MTD is a +3.3 V, 85 MHz, 28-bit Channel Link transmitter that converts parallel LVCMOS/LVTTL data into four LVDS data streams. Texas Instruments identifies it as a rising-edge data-strobe transmitter with a separately transmitted phase-locked clock and a 56-pin TSSOP package, making it suitable for high-speed parallel-to-differential industrial data links.
How many LVDS outputs does DS90CR287MTD provide?
The DS90CR287MTD provides five differential LVDS outputs in total: four carry serialized data and a fifth carries the phase-locked transmit clock. According to the Texas Instruments product description, all 28 input bits are transferred during each transmit-clock cycle, allowing the receiver to capture the payload using the forwarded clock as its timing reference.
What is the maximum operating frequency of DS90CR287MTD?
The DS90CR287MTD operates up to 85 MHz. At that clock rate, the five-lane architecture provides an aggregate data rate of 2380 Mbps according to the manufacturer product information. The usable channel distance and signal integrity margin can be shorter in practice than a nominal maximum rate, so receiver timing, cable, connector, and PCB impedance must also be evaluated.
Where can I download the DS90CR287MTD datasheet PDF?
The official DS90CR287MTD documentation is available through the Texas Instruments product page at https://www.ti.com/product/DS90CR287. Use the datasheet link on that page for the complete electrical tables, timing diagrams, pin descriptions, LVDS output characteristics, and application guidance. A third-party datasheet mirror is also listed, but the manufacturer page is the preferred starting point for revision control.
Where can I find the DS90CR287MTD pinout?
The DS90CR287MTD pinout is documented in the pin-description table and package drawing of the Texas Instruments DS90CR287 datasheet. The device is a 56-pin TSSOP with 28 parallel data inputs, control connections, supply pins, and five differential LVDS outputs. Assign every signal from the pin-description table because the exact connector and no-connect assignments must be followed in the PCB layout.
Can DS90CR287MTD replace DS90CR287MTD/NOPB?
The DS90CR287MTD and DS90CR287MTD/NOPB identify the same Texas Instruments Channel Link transmitter, and cross-reference information describes the NOPB version as completely replaceable because its terminals, packages, and main performance characteristics are consistent. The NOPB ordering code may indicate a different terminal-finish or lead-free ordering treatment, so confirm the current manufacturer ordering information before treating the suffix codes as interchangeable.
What is the best drop-in replacement for DS90CR287MTD?
The best directly documented drop-in replacement is DS90CR287MTD/NOPB, which cross-reference information describes as having consistent terminals, package, and principal performance characteristics. DS90CR287MTDX/NOPB is another identified ordering variant in the same device family. A replacement should be approved only after checking the exact suffix, pin assignment, supply requirements, timing specifications, and operating-temperature limits in the manufacturer datasheet.
Is DS90CR287MTD suitable for industrial imaging and video systems?
The DS90CR287MTD is suitable for industrial imaging and video transport systems that use a 28-bit parallel source and require multiple high-speed differential lanes. Its 85 MHz rate, four LVDS data outputs, transmitted clock, and -10°C to +70°C operating range fit many industrial equipment designs. The system still requires receiver compatibility, controlled-impedance routing, suitable cables, and verified connector performance.
DS90CR287MTD vs DS90CR286MTD: which transmitter should I select?
The DS90CR287MTD is the choice when the design specifically requires the documented 28-bit, +3.3 V, 85 MHz Channel Link transmitter with four LVDS data streams and a transmitted clock. Cross-reference material identifies DS90CR286MTD as a related comparison part, but the snippet does not establish identical pin compatibility. Review the two manufacturer datasheets before selecting it as a board-level replacement.
When should I choose DS90CR287MTD over DS90CF386MTD?
Choose DS90CR287MTD when the transmitter requirements match its specified +3.3 V, 85 MHz, 28-bit LVDS Channel Link operation and rising-edge data-strobe architecture. DS90CF386MTD is a related part identified in comparison resources, but those resources do not prove identical pinout or timing. Treat DS90CF386MTD as a redesign candidate unless its manufacturer datasheet confirms a matching footprint and electrical interface.
What can replace DS90CR287MTD?
DS90CR287MTD/NOPB is the clearest documented replacement because cross-reference information states that its terminals, package, and main performance characteristics are consistent with DS90CR287MTD. DS90CR287MTDX/NOPB is also present as a related ordering designation. No cross-brand drop-in replacement is established by the available manufacturer and cross-reference material, so an alternative from another manufacturer should not be assumed to be pin compatible.
Is DS90CR287MTD the same as DS90CR286AMTD?
No exact equivalence is established between DS90CR287MTD and DS90CR286AMTD by the available manufacturer information. The devices appear in comparison resources as related interface ICs, but the cited material does not verify identical pin assignments, output structure, timing, or operating limits. Use the DS90CR287MTD and DS90CR286AMTD datasheets to determine whether the receiver and PCB interface can be retained.
Where can I buy DS90CR287MTD and what is the price?
Use the Request a Quote form on this page to request current DS90CR287MTD pricing, stock confirmation, lead time, and minimum order quantity. The product is listed as a Texas Instruments 56-pin TSSOP interface IC by major authorized distributors, but current commercial terms can change and should be confirmed for the exact ordering suffix. The quote form avoids presenting a stale price or unconfirmed inventory claim.
What is the lead time and stock status for DS90CR287MTD?
Current stock and lead time for DS90CR287MTD should be confirmed through the Request a Quote form on this page. One distributor listing indicates that the part ships from stock, but availability at a distributor does not establish a guaranteed factory lead time or a permanent inventory position. Include your required quantity, date code needs, and shipping destination when requesting the quotation.
What are the key specifications of DS90CR287MTD that engineers should know?
The key DS90CR287MTD specifications are a +3.3 V supply, 85 MHz operating frequency, 28 LVCMOS/LVTTL input bits, four differential LVDS data outputs, one differential transmit-clock output, a 2380 Mbps aggregate data rate, and a 56-pin TSSOP package. The device uses rising-edge data strobing and an operating range of -10°C to +70°C, making receiver and interconnect compatibility central to design qualification.

Engineering reference data for DS90CR287MTD — comparison, design guidance, and compliance information.

Selection Guide

Choose DS90CR287MTD for a 28-bit parallel-to-LVDS design that requires a +3.3 V supply, an 85 MHz rising-edge data-strobe interface, four differential data outputs, and a separately transmitted phase-locked clock. DS90CR287MTD/NOPB is the preferred documented replacement when the ordering suffix is acceptable because its terminals, package, and principal performance characteristics are described as consistent. DS90CR287MTDX/NOPB is another same-family ordering designation that should be checked against current ordering and marking rules. DS90CR286MTD and DS90CR286AMTD appear in comparison resources, but their availability as true board-level replacements is not proven because equivalent pinout and timing are not established. DS90CF386MTD should likewise be treated as a redesign candidate unless its datasheet confirms the same footprint, clocking method, output count, and receiver compatibility.

Comparison with Alternatives

Parameter This Product DS90CR287MTD/NOPB DS90CR287MTDX/NOPB DS90CR287MTD/NOPB
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 56-pin TSSOP 56-pin TSSOP - same 56-pin TSSOP - same 56-pin TSSOP - same
Supply Voltage +3.3 V +3.3 V +3.3 V +3.3 V
Operating Frequency 85 MHz 85 MHz 85 MHz 85 MHz
Input Data Width 28 bits 28 bits 28 bits 28 bits
LVDS Data Outputs 4 differential data streams 4 differential data streams 4 differential data streams 4 differential data streams
Clock Output 1 differential LVDS transmit-clock stream 1 differential LVDS transmit-clock stream 1 differential LVDS transmit-clock stream 1 differential LVDS transmit-clock stream
Aggregate Data Rate 2380 Mbps 2380 Mbps 2380 Mbps 2380 Mbps
Operating Temperature -10°C to +70°C -10°C to +70°C -10°C to +70°C -10°C to +70°C
Input Logic LVCMOS/LVTTL LVCMOS/LVTTL LVCMOS/LVTTL LVCMOS/LVTTL

Key Differentiators

  • Wide parallel input with compact differential output (vs DS90CF386MTD)
  • Exact-family ordering replacement available (vs DS90CR287MTD/NOPB)
  • Source-synchronous clocking is integrated (vs DS90CR286AMTD)

Design Notes

Route each LVDS output as a controlled-impedance differential pair with closely matched spacing, symmetric length, and minimal vias. Keep stubs short and preserve consistent return-path continuity across the PCB stack-up. The transmitter clock pair should follow the same layout discipline as the four data pairs because timing margin at the receiver depends on the relative flight time of all five links.

Do not assume that two related Channel Link devices are interchangeable because their descriptions look similar. Confirm the 56-pin TSSOP pin assignments, +3.3 V supply, 85 MHz timing, rising-edge data strobe, output mapping, and receiver protocol from the manufacturer datasheet. In particular, verify that the receiving circuit captures data relative to the transmitted clock rather than using an incompatible source-synchronous scheme.

Qualify the complete link rather than only the transmitter output. Characterize receiver thresholds and tolerances, cable attenuation, connector transitions, pair skew, and PCB loss at the intended operating frequency. The 85 MHz headline rate does not by itself establish reliable end-to-end operation at a specified cable length, so perform eye or compliance measurements with representative interconnects.

Place bypass capacitance close to the +3.3 V supply pins and provide a low-impedance ground return for the transmitter. Follow the datasheet guidance for supply and ground connectivity, and use a solid ground plane beneath the signal-routing region when the stack-up permits it. Separate the LVDS outputs from sensitive single-ended inputs to reduce coupling into the 28-bit parallel interface.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The current product description identifies the device as a +3.3 V, 85 MHz, 28-bit Channel Link transmitter in a 56-pin TSSOP package. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status should be confirmed for the exact ordering suffix through the manufacturer product documentation.

Data verified on: 2026-11-10 — data verified and curated by XAIPART's component engineering team

Related Searches

ds90cr287mtd nopb DS90CR287MTD datasheet DS90CR287MTD datasheet pdf DS90CR287MTD pinout DS90CR287MTD equivalent DS90CR287MTD replacement DS90CR287MTD cross reference DS90CR287MTD vs DS90CR286MTD DS90CR287MTD footprint DS90CR287MTD 56 pin TSSOP Texas Instruments DS90CR287MTD DS90CR287MTD price DS90CR287MTD stock

Related Components & Terms

Texas Instruments DS90CR287MTD DS90CR287MTD/NOPB DS90CR287MTDX/NOPB DS90CR286MTD DS90CR286AMTD DS90CF386MTD LVDS Channel Link LVDS transmitter parallel-to-differential interface interface IC LVCMOS LVTTL source-synchronous clock phase-locked transmit clock differential signal 85 MHz clock 2380 Mbps data rate 56-pin TSSOP TSSOP package surface-mount package industrial imaging video transport data acquisition
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details