DS90CR287MTD - 85MHz 28-Bit LVDS Transmitter | Texas Instruments
MPN: DS90CR287MTD ✓ פעילDS90CR287MTD סקירה
A Channel Link transmitter is a high-speed parallel-to-differential interface IC used to move multiple data bits across a cable or PCB interconnect. The DS90CR287 belongs to the LVDS interface IC hierarchy, which includes differential line drivers, channel-link serializers, clock transmitters, and receiver counterparts. Its parallel-to-LVDS architecture reduces the number of signal conductors required for wide data transfers while supporting reliable clocking across that link.
The principal features include 28 LVCMOS/LVTTL data inputs, four LVDS data streams, a fifth differential clock output, an 85 MHz operating frequency, and operation from a +3.3 V supply. The transmitter is intended for rising-edge data-strobe applications and supports an industrial temperature range of -10°C to +70°C. A 56-pin TSSOP provides adequate routing density for the wide parallel input interface and five differential outputs.
Technically, the device serializes each cycle of the transmit clock into four differential data lanes. The transmitted clock provides a source-synchronous reference at the receiver, allowing the receiving system to capture the data relative to the forwarded clock. This architecture is useful when the source and destination must exchange parallel data across a limited number of high-speed conductors while retaining deterministic timing.
Typical applications include industrial imaging equipment, video transport systems, data-acquisition modules, digital cameras, test and measurement instruments, and industrial control panels. The 28-bit parallel input and multi-lane LVDS output can reduce connector pin count compared with driving every parallel bit as a single-ended signal, especially in space-constrained equipment.
The key design consideration is that the LVDS link still requires controlled impedance, short stubs, suitable connectors, and compliant differential routing. Input and output timing, cable length, connector behavior, and receiver capability determine whether the full 85 MHz operating rate is practical in a specific system.
This product page organizes the DS90CR287MTD interface details, verified source links, replacement analysis, and application guidance into a design-focused reference for engineers evaluating parallel-to-LVDS data links.
חלופות תחליף ישיר עבור DS90CR287MTD — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם DS90CR287MTD (אותו גורם צורה וטביעת רגל) — שונים ב Package, Supply Voltage.
DS90CR287MTD/NOPB
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DS90CR287MTDX/NOPB
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DS90CR287MTD/NOPB
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DS90CR287MTD מפרטים
| Product Type | LVDS 28-bit Channel Link transmitter |
| מתח אספקה | +3.3 V |
| Operating Frequency | 85 MHz |
| Data Input Width | 28 bits |
| Input Logic | LVCMOS/LVTTL |
| LVDS Data Outputs | 4 differential data streams |
| Clock Output | 1 differential LVDS transmit-clock stream |
| Data Transfer Edge | Rising edge |
| מארז | 56-pin TSSOP |
| סוג הרכבה | Surface mount |
| טמפרטורת פעולה | -10°C to +70°C |
| Output Differential Voltage | 0.45 V |
| קצב נתונים | 2380 Mbps |
מדריך תצורת פינים של DS90CR287MTD 56-pin tssop
תצורת פינים עבור DS90CR287MTD (מארזת 56-pin tssop). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור DS90CR287MTD.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
DS90CR287MTD מתאים עבור 6 יישוםs: Industrial Camera Data Transport, Digital Video Transport, Data Acquisition Systems, Test and Measurement Equipment, Industrial Control Panels, Medical Imaging Interfaces.
Industrial Camera Data Transport
The DS90CR287MTD fits parallel-output image sensors and industrial cameras that need to transfer 28 data bits per clock without allocating one connector conductor for every LVCMOS bit. Its four LVDS data lanes plus transmitted clock reduce the link width while preserving a source-synchronous 85 MHz operating rate. Designers should match the receiver to the 28-bit frame and clock timing, then validate differential routing, connector loss, and cable length under the intended temperature conditions.
מומלץ
Digital Video Transport
The DS90CR287MTD can carry wide parallel video or pixel data across a compact LVDS connection by converting 28 LVCMOS/LVTTL bits into four differential data streams and one transmitted clock. At 85 MHz, the documented aggregate rate is 2380 Mbps, which is useful for transporting parallel raster or frame data inside industrial monitoring equipment. The implementation depends on receiver timing tolerance, LVDS pair routing, and a connector and cable characterized for the target transfer distance.
מומלץ
Data Acquisition Systems
For multi-channel data-acquisition and control systems, the DS90CR287MTD provides a parallel-to-differential transition between an FPGA or processor bus and a remote receiver card. Its 28 input bits can represent counters, status flags, samples, or timestamp data, while the phase-locked transmit clock supports deterministic capture at the destination. PCB implementation should preserve LVDS impedance and pair symmetry, minimize stubs, and confirm that the downstream receiver supports the same 85 MHz data-strobe protocol.
מומלץ
Test and Measurement Equipment
The DS90CR287MTD is useful in test and measurement instruments that move wide parallel result or control data between circuit boards while limiting cable count. The +3.3 V operation, 85 MHz Channel Link rate, and transmitted differential clock suit source-synchronous backplane or cable links requiring repeatable timing. For bench equipment, qualify the complete interconnect including cables, connectors, and receiver loading, and check the -10°C to +70°C range against the enclosure temperature.
מומלץ
Industrial Control Panels
The DS90CR287MTD can bridge a control module and display or processing electronics by transporting 28 command and status bits over four LVDS data pairs and one clock pair. The reduced conductor count can simplify high-density backplane or cable assemblies compared with parallel single-ended routing. Engineers should treat the transmitted clock and receiver capture timing as a matched interface, maintain controlled differential impedance, and verify cable length and temperature performance before production release.
מומלץ
Medical Imaging Interfaces
The DS90CR287MTD can support high-density image or control-data transfer in medical imaging equipment where a 28-bit parallel source must be serialized onto differential lanes. The 85 MHz rate allows wide data movement with five differential outputs, including the transmitted clock used for source-synchronous capture. Any medical use requires system-level validation of receiver compatibility, signal integrity, electrical isolation requirements, and applicable sector-specific quality procedures beyond the component's stated temperature range.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור DS90CR287MTD — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | DS90CR287MTD/NOPB | DS90CR287MTDX/NOPB | DS90CR287MTD/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 56-pin TSSOP | 56-pin TSSOP - same | 56-pin TSSOP - same | 56-pin TSSOP - same |
| Supply Voltage | +3.3 V | +3.3 V | +3.3 V | +3.3 V |
| Operating Frequency | 85 MHz | 85 MHz | 85 MHz | 85 MHz |
| Input Data Width | 28 bits | 28 bits | 28 bits | 28 bits |
| LVDS Data Outputs | 4 differential data streams | 4 differential data streams | 4 differential data streams | 4 differential data streams |
| Clock Output | 1 differential LVDS transmit-clock stream | 1 differential LVDS transmit-clock stream | 1 differential LVDS transmit-clock stream | 1 differential LVDS transmit-clock stream |
| Aggregate Data Rate | 2380 Mbps | 2380 Mbps | 2380 Mbps | 2380 Mbps |
| Operating Temperature | -10°C to +70°C | -10°C to +70°C | -10°C to +70°C | -10°C to +70°C |
| Input Logic | LVCMOS/LVTTL | LVCMOS/LVTTL | LVCMOS/LVTTL | LVCMOS/LVTTL |
מבדילים עיקריים
- Wide parallel input with compact differential output (לעומתDS90CF386MTD)
- Exact-family ordering replacement available (לעומתDS90CR287MTD/NOPB)
- Source-synchronous clocking is integrated (לעומתDS90CR286AMTD)
הערות תכנון
Route each LVDS output as a controlled-impedance differential pair with closely matched spacing, symmetric length, and minimal vias. Keep stubs short and preserve consistent return-path continuity across the PCB stack-up. The transmitter clock pair should follow the same layout discipline as the four data pairs because timing margin at the receiver depends on the relative flight time of all five links.
Do not assume that two related Channel Link devices are interchangeable because their descriptions look similar. Confirm the 56-pin TSSOP pin assignments, +3.3 V supply, 85 MHz timing, rising-edge data strobe, output mapping, and receiver protocol from the manufacturer datasheet. In particular, verify that the receiving circuit captures data relative to the transmitted clock rather than using an incompatible source-synchronous scheme.
Qualify the complete link rather than only the transmitter output. Characterize receiver thresholds and tolerances, cable attenuation, connector transitions, pair skew, and PCB loss at the intended operating frequency. The 85 MHz headline rate does not by itself establish reliable end-to-end operation at a specified cable length, so perform eye or compliance measurements with representative interconnects.
Place bypass capacitance close to the +3.3 V supply pins and provide a low-impedance ground return for the transmitter. Follow the datasheet guidance for supply and ground connectivity, and use a solid ground plane beneath the signal-routing region when the stack-up permits it. Separate the LVDS outputs from sensitive single-ended inputs to reduce coupling into the 28-bit parallel interface.
מידע על תאימות
The current product description identifies the device as a +3.3 V, 85 MHz, 28-bit Channel Link transmitter in a 56-pin TSSOP package. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status should be confirmed for the exact ordering suffix through the manufacturer product documentation.