DS90LV047ATMTC - 400 Mbps LVDS Quad Driver | Texas Instruments
MPN: DS90LV047ATMTC ✓ ActiveDS90LV047ATMTC Overview
An LVDS differential line driver is an interface IC that converts single-ended digital signals into low-voltage differential pairs. Low Voltage Differential Signaling belongs to the interface IC category and uses the voltage difference between two conductors to carry data while rejecting common-mode noise. By placing four LVDS outputs in one package, the DS90LV047A family reduces component count and simplifies control of parallel data buses, clock distribution, and multi-channel point-to-point interconnects.
The principal characteristics are a 400 Mbps signaling rate, four independent differential outputs, a 3.3 V supply, and CMOS-compatible inputs. Each driver supports low-power operation and fast data-rate transmission for point-to-point links. The 16-pin TSSOP package provides a compact surface-mount footprint suitable for communications equipment, industrial controls, test equipment, and multi-channel digital backplanes.
The device uses differential signaling to maintain signal integrity over cables or controlled-impedance PCB traces. Because the receiver detects the voltage difference across the pair rather than an absolute voltage at one conductor, common-mode disturbances caused by nearby switching circuitry are substantially rejected. Four channels can transmit related control, data, or clock signals while keeping channel-to-channel skew and power distribution under centralized design control.
Typical uses include parallel-to-serial data transmission, clock distribution, backplane links, video and imaging interfaces, industrial automation equipment, and test-and-measurement systems. The quad architecture is particularly useful when four independent high-speed channels must share the same supply, ground, and board area. The device is designed to work with the companion DS90LV048A family of quad LVDS receivers when a system requires balanced transmission and reception.
PCB implementation should use controlled-impedance differential routing, symmetric pair geometry, and a continuous ground reference beneath the signal traces. Keep the LVDS outputs away from high-current switching paths, and terminate the receiving end according to the receiver manufacturer's recommendations. Verify the final eye pattern, skew, and common-mode behavior at the system level because connector and cable effects can materially limit a 400 Mbps link.
This page consolidates manufacturer product information, ordering details, cross-reference candidates, and practical interface-design guidance. It also identifies the distinctions between the available ordering codes so engineers can select a functionally equivalent part without overlooking packing, marking, or temperature-range differences.
Drop-in alternatives for DS90LV047ATMTC — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with DS90LV047ATMTC (same form factor and footprint) — differing in Operating Temperature Range, Package.
DS90LV047ATMTC/NOPB
✅ Drop-InContact for price
View Datasheet →DS90LV047ATMTCX/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV047ATM/NOPB
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV047ATMTC/DRPB
✅ Drop-In📋 Reference alternative (not in catalog)
PI90LV047ALE
✅ Drop-In📋 Reference alternative (not in catalog)
DS90LV047ATMTC Specifications
| Device Type | 4/0 LVDS differential line driver |
| Number of Differential Drivers | 4 |
| Maximum Signaling Rate | 400 Mbps |
| Nominal Supply Voltage | 3.3 V |
| Input Signal Compatibility | CMOS, LVTTL, TTL |
| Output Signal Type | LVDS differential |
| LVDS Output Voltage | 0.45 V |
| Package | 16-pin TSSOP (PW) |
| Mounting Type | Surface mount |
| Operating Temperature Range | -40 °C to 85 °C |
DS90LV047ATMTC 16-pin tssop (pw) Pin Configuration Guide
Pin configuration for DS90LV047ATMTC (16-pin tssop (pw) package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for DS90LV047ATMTC.
Refer to the datasheet for full pin configuration.
Typical Applications
DS90LV047ATMTC is suitable for 6 applications: High-Speed Parallel-to-Serial Data Transmission, Multi-Channel Clock Distribution, Industrial Automation and Control Links, Test and Measurement Instrumentation, Backplane and Board-to-Board Interconnects, Imaging and Video Interface Modules.
High-Speed Parallel-to-Serial Data Transmission
The DS90LV047ATMTC fits four-channel parallel-to-serial links that require LVDS outputs at rates up to 400 Mbps. Each of the four drivers accepts a CMOS, LVTTL, or TTL signal and converts it into a low-voltage differential pair. This allows a controller or FPGA to drive four related channels over controlled-impedance board traces or balanced cables. The 3.3 V supply and 16-pin TSSOP package limit board area, while differential signaling improves noise immunity in systems with nearby switching circuitry.
Recommended
Multi-Channel Clock Distribution
The four differential outputs of the DS90LV047ATMTC can distribute related or independent clock signals across a cabinet, backplane, or instrumented test system. Operating at a 3.3 V supply and supporting signaling rates up to 400 Mbps provides headroom for low-jitter digital clock links. A common package also keeps channel-to-channel placement consistent, making return-path and pair-length management easier. Validate receiver input capacitance and clock fanout before assigning all four channels.
Recommended
Industrial Automation and Control Links
The DS90LV047ATMTC is suitable for factory equipment that transfers control, position, or diagnostic data between controller cards and remote modules. Four 400 Mbps-capable LVDS drivers provide a compact interface for parallel buses, while differential pairs reduce susceptibility to common-mode noise found in industrial environments. The -40 °C to 85 °C rated part supports a broad range of industrial temperature conditions. Use controlled-impedance routing and keep switching-power paths separated from the LVDS outputs.
Recommended
Test and Measurement Instrumentation
The DS90LV047ATMTC can drive four differential channels in automated test equipment, signal-conditioning modules, and acquisition backplanes. Its 400 Mbps signaling capability supports high-rate digital stimulus while the compact 16-pin TSSOP package simplifies board-level integration. The transmitter-only architecture leaves receiver selection flexible, allowing it to pair with the DS90LV048A family or another compatible LVDS receiver. Confirm eye margin, jitter budget, and termination values at the intended cable length.
Recommended
Backplane and Board-to-Board Interconnects
Four LVDS outputs allow the DS90LV047ATMTC to serve as a compact transmitter on a backplane or inter-board interface. At rates up to 400 Mbps, the device can carry multiple low-latency data lanes while differential signaling improves noise immunity over short board-to-board connections. A 16-pin TSSOP package supports dense placement, but high-speed performance depends on stack-up impedance, via geometry, connector transitions, and return-path continuity. Model the complete channel rather than only the driver output.
Recommended
Imaging and Video Interface Modules
The DS90LV047ATMTC can provide four low-voltage differential outputs for parallel imaging data, synchronization signals, or video timing distribution. The 400 Mbps capability accommodates several high-speed digital functions while the 3.3 V operation integrates cleanly with modern CMOS logic. Because LVDS performance is sensitive to trace geometry and crosstalk, maintain symmetric pair spacing, avoid stubs, and provide a continuous reference plane. Verify the source and receiver timing specifications against the actual pixel or frame-rate requirement.
Recommended
Recommended Products Summary
Engineering reference data for DS90LV047ATMTC — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | DS90LV047ATMTC/NOPB | DS90LV047ATMTCX/NOPB | DS90LV047ATM/NOPB | DS90LV047ATMTC/DRPB | PI90LV047ALE |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Pericom Semiconductor |
| Package | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP |
| Device Type | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | Quad LVDS differential line driver |
| Maximum Signaling Rate | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Number of Differential Drivers | 4 | 4 | 4 | 4 | 4 | 4 |
| Number of Receivers | 0 | 0 | 0 | 0 | 0 | 0 |
| Output Signal | LVDS differential | LVDS differential | LVDS differential | LVDS differential | LVDS differential | LVDS differential |
Key Differentiators
- Four transmit channels integrated into one compact package (vs DS90LV048ATMTC/NOPB)
- Direct single-manufacturer alternative path (vs PI90LV047ALE)
- Wide specified industrial temperature range (vs PI90LV047ALE)
Design Notes
Route every LVDS output as a controlled-impedance differential pair with symmetric geometry and a continuous ground reference beneath the traces. Define the target differential impedance from the actual PCB stack-up and use the same general topology for all four channels. Avoid stubs, unnecessary vias, and abrupt width changes. Keep the driver outputs away from inductors, high-current switching loops, and clocks with fast edges because those sources can create common-mode noise and degrade receiver eye margins.
Place the DS90LV047ATMTC close to the source of the four input signals and to the connector or transmission-line origin. Provide a low-impedance 3.3 V plane and place local supply bypassing between the device supply pin and the nearest ground reference, following the capacitance values and layout recommendations in the manufacturer datasheet. Maintain a short, uninterrupted return path beneath each pair. When the links cross a connector or board boundary, verify differential impedance, insertion loss, and return loss across the complete channel.
Do not treat the 400 Mbps signaling-rate rating as a guaranteed end-to-end performance guarantee. Evaluate input-to-output timing, channel skew, jitter, receiver threshold, connector and cable loss, and the required mask. Measure eye diagrams at the receiving endpoint with realistic patterns and equalization, if used. The DS90LV048ATMTC/NOPB family provides a compatible receiver function, but a complete link still requires separate confirmation of source encoding, clock topology, and termination.
Avoid confusing the DS90LV047A transmitter with the DS90LV048A receiver or with unrelated single-channel LVDS drivers. Confirm that the selected ordering code retains the four-driver, zero-receiver configuration, the 16-pin TSSOP (PW) footprint, and the required 3.3 V supply. Also avoid assuming that every similarly named ordering code has identical temperature or shipping documentation. Review the manufacturer ordering table before releasing a BOM or approving a second-source substitution.
Compliance Information
Compliance status is not stated for this specific ordering code in the manufacturer product information and cross-reference listings. Verify RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation for the exact assembled ordering option before release.