DS90LV047ATMTC - 400 Mbps LVDS Quad Driver | Texas Instruments
MPN: DS90LV047ATMTC ✓ 啟用中DS90LV047ATMTC 概覽
An LVDS differential line driver is an interface IC that converts single-ended digital signals into low-voltage differential pairs. Low Voltage Differential Signaling belongs to the interface IC category and uses the voltage difference between two conductors to carry data while rejecting common-mode noise. By placing four LVDS outputs in one package, the DS90LV047A family reduces component count and simplifies control of parallel data buses, clock distribution, and multi-channel point-to-point interconnects.
The principal characteristics are a 400 Mbps signaling rate, four independent differential outputs, a 3.3 V supply, and CMOS-compatible inputs. Each driver supports low-power operation and fast data-rate transmission for point-to-point links. The 16-pin TSSOP package provides a compact surface-mount footprint suitable for communications equipment, industrial controls, test equipment, and multi-channel digital backplanes.
The device uses differential signaling to maintain signal integrity over cables or controlled-impedance PCB traces. Because the receiver detects the voltage difference across the pair rather than an absolute voltage at one conductor, common-mode disturbances caused by nearby switching circuitry are substantially rejected. Four channels can transmit related control, data, or clock signals while keeping channel-to-channel skew and power distribution under centralized design control.
Typical uses include parallel-to-serial data transmission, clock distribution, backplane links, video and imaging interfaces, industrial automation equipment, and test-and-measurement systems. The quad architecture is particularly useful when four independent high-speed channels must share the same supply, ground, and board area. The device is designed to work with the companion DS90LV048A family of quad LVDS receivers when a system requires balanced transmission and reception.
PCB implementation should use controlled-impedance differential routing, symmetric pair geometry, and a continuous ground reference beneath the signal traces. Keep the LVDS outputs away from high-current switching paths, and terminate the receiving end according to the receiver manufacturer's recommendations. Verify the final eye pattern, skew, and common-mode behavior at the system level because connector and cable effects can materially limit a 400 Mbps link.
This page consolidates manufacturer product information, ordering details, cross-reference candidates, and practical interface-design guidance. It also identifies the distinctions between the available ordering codes so engineers can select a functionally equivalent part without overlooking packing, marking, or temperature-range differences.
直接替換替代品,適用於 DS90LV047ATMTC — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: DS90LV047ATMTC (相同外形與佔位) — 差異在於 Operating Temperature Range, Package.
DS90LV047ATMTC/NOPB
✅ 直接替換聯絡詢價
查看資料表 →DS90LV047ATMTCX/NOPB
✅ 直接替換📋 參考替代品(不在目錄中)
DS90LV047ATM/NOPB
✅ 直接替換📋 參考替代品(不在目錄中)
DS90LV047ATMTC/DRPB
✅ 直接替換📋 參考替代品(不在目錄中)
PI90LV047ALE
✅ 直接替換📋 參考替代品(不在目錄中)
DS90LV047ATMTC 規格
| Device Type | 4/0 LVDS differential line driver |
| Number of Differential Drivers | 4 |
| Maximum Signaling Rate | 400 Mbps |
| Nominal Supply Voltage | 3.3 V |
| Input Signal Compatibility | CMOS, LVTTL, TTL |
| Output Signal Type | LVDS differential |
| LVDS Output Voltage | 0.45 V |
| 封裝 | 16-pin TSSOP (PW) |
| 安裝類型 | Surface mount |
| 工作溫度範圍 | -40 °C to 85 °C |
DS90LV047ATMTC 16-pin tssop (pw) 腳位配置指南
DS90LV047ATMTC(16-pin tssop (pw) 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: DS90LV047ATMTC.
請參閱 資料表 以查看完整腳位配置。
典型應用
DS90LV047ATMTC 適用於 6 應用s: High-Speed Parallel-to-Serial Data Transmission, Multi-Channel Clock Distribution, Industrial Automation and Control Links, Test and Measurement Instrumentation, Backplane and Board-to-Board Interconnects, Imaging and Video Interface Modules.
High-Speed Parallel-to-Serial Data Transmission
The DS90LV047ATMTC fits four-channel parallel-to-serial links that require LVDS outputs at rates up to 400 Mbps. Each of the four drivers accepts a CMOS, LVTTL, or TTL signal and converts it into a low-voltage differential pair. This allows a controller or FPGA to drive four related channels over controlled-impedance board traces or balanced cables. The 3.3 V supply and 16-pin TSSOP package limit board area, while differential signaling improves noise immunity in systems with nearby switching circuitry.
推薦
Multi-Channel Clock Distribution
The four differential outputs of the DS90LV047ATMTC can distribute related or independent clock signals across a cabinet, backplane, or instrumented test system. Operating at a 3.3 V supply and supporting signaling rates up to 400 Mbps provides headroom for low-jitter digital clock links. A common package also keeps channel-to-channel placement consistent, making return-path and pair-length management easier. Validate receiver input capacitance and clock fanout before assigning all four channels.
推薦
Industrial Automation and Control Links
The DS90LV047ATMTC is suitable for factory equipment that transfers control, position, or diagnostic data between controller cards and remote modules. Four 400 Mbps-capable LVDS drivers provide a compact interface for parallel buses, while differential pairs reduce susceptibility to common-mode noise found in industrial environments. The -40 °C to 85 °C rated part supports a broad range of industrial temperature conditions. Use controlled-impedance routing and keep switching-power paths separated from the LVDS outputs.
推薦
Test and Measurement Instrumentation
The DS90LV047ATMTC can drive four differential channels in automated test equipment, signal-conditioning modules, and acquisition backplanes. Its 400 Mbps signaling capability supports high-rate digital stimulus while the compact 16-pin TSSOP package simplifies board-level integration. The transmitter-only architecture leaves receiver selection flexible, allowing it to pair with the DS90LV048A family or another compatible LVDS receiver. Confirm eye margin, jitter budget, and termination values at the intended cable length.
推薦
Backplane and Board-to-Board Interconnects
Four LVDS outputs allow the DS90LV047ATMTC to serve as a compact transmitter on a backplane or inter-board interface. At rates up to 400 Mbps, the device can carry multiple low-latency data lanes while differential signaling improves noise immunity over short board-to-board connections. A 16-pin TSSOP package supports dense placement, but high-speed performance depends on stack-up impedance, via geometry, connector transitions, and return-path continuity. Model the complete channel rather than only the driver output.
推薦
Imaging and Video Interface Modules
The DS90LV047ATMTC can provide four low-voltage differential outputs for parallel imaging data, synchronization signals, or video timing distribution. The 400 Mbps capability accommodates several high-speed digital functions while the 3.3 V operation integrates cleanly with modern CMOS logic. Because LVDS performance is sensitive to trace geometry and crosstalk, maintain symmetric pair spacing, avoid stubs, and provide a continuous reference plane. Verify the source and receiver timing specifications against the actual pixel or frame-rate requirement.
推薦
推薦產品摘要
工程參考資料,適用於 DS90LV047ATMTC — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | DS90LV047ATMTC/NOPB | DS90LV047ATMTCX/NOPB | DS90LV047ATM/NOPB | DS90LV047ATMTC/DRPB | PI90LV047ALE |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Pericom Semiconductor |
| Package | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP (PW) | 16-pin TSSOP |
| Device Type | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | 4/0 quad LVDS differential line driver | Quad LVDS differential line driver |
| Maximum Signaling Rate | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps | 400 Mbps |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Number of Differential Drivers | 4 | 4 | 4 | 4 | 4 | 4 |
| Number of Receivers | 0 | 0 | 0 | 0 | 0 | 0 |
| Output Signal | LVDS differential | LVDS differential | LVDS differential | LVDS differential | LVDS differential | LVDS differential |
主要差異化特點
- Four transmit channels integrated into one compact package (對比DS90LV048ATMTC/NOPB)
- Direct single-manufacturer alternative path (對比PI90LV047ALE)
- Wide specified industrial temperature range (對比PI90LV047ALE)
設計說明
Route every LVDS output as a controlled-impedance differential pair with symmetric geometry and a continuous ground reference beneath the traces. Define the target differential impedance from the actual PCB stack-up and use the same general topology for all four channels. Avoid stubs, unnecessary vias, and abrupt width changes. Keep the driver outputs away from inductors, high-current switching loops, and clocks with fast edges because those sources can create common-mode noise and degrade receiver eye margins.
Place the DS90LV047ATMTC close to the source of the four input signals and to the connector or transmission-line origin. Provide a low-impedance 3.3 V plane and place local supply bypassing between the device supply pin and the nearest ground reference, following the capacitance values and layout recommendations in the manufacturer datasheet. Maintain a short, uninterrupted return path beneath each pair. When the links cross a connector or board boundary, verify differential impedance, insertion loss, and return loss across the complete channel.
Do not treat the 400 Mbps signaling-rate rating as a guaranteed end-to-end performance guarantee. Evaluate input-to-output timing, channel skew, jitter, receiver threshold, connector and cable loss, and the required mask. Measure eye diagrams at the receiving endpoint with realistic patterns and equalization, if used. The DS90LV048ATMTC/NOPB family provides a compatible receiver function, but a complete link still requires separate confirmation of source encoding, clock topology, and termination.
Avoid confusing the DS90LV047A transmitter with the DS90LV048A receiver or with unrelated single-channel LVDS drivers. Confirm that the selected ordering code retains the four-driver, zero-receiver configuration, the 16-pin TSSOP (PW) footprint, and the required 3.3 V supply. Also avoid assuming that every similarly named ordering code has identical temperature or shipping documentation. Review the manufacturer ordering table before releasing a BOM or approving a second-source substitution.
合規資訊
Compliance status is not stated for this specific ordering code in the manufacturer product information and cross-reference listings. Verify RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation for the exact assembled ordering option before release.