IDTADC1005S060TS-C18 - 10-Bit 60MSPS ULP ADC | Renesas (IDT)
MPN: IDTADC1005S060TS-C18 ✓ Active| Qty | Unit Price | Extended |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.85 | $1,385.00 |
| 500 | $11.4 | $5,700.00 |
| 1,000 | $9.75 | $9,750.00 |
IDTADC1005S060TS-C18 Overview
An analog-to-digital converter (ADC) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes at a specified sample rate. Within the broader data-converter hierarchy, the IDTADC1005S060TS-C18 sits in the flash-architecture sub-category, which uses a parallel bank of comparators for the fastest possible conversion at the expense of higher power and silicon area. Flash ADCs are typically deployed when sub-100 ns latency and sub-100 MSPS sampling are required. The ADC1005 family extends the IDT/Renesas data-converter portfolio targeting industrial control, instrumentation, and communications front-ends.
Key specifications include 10-bit resolution, 60 MSPS maximum sampling rate, single-channel differential input, and an ultra-low-power operating profile suitable for thermally constrained boards. The device supports a single 5 V analog supply plus a 5 V digital supply, simplifying power-tree design in legacy 5 V systems. Internal reference and track-and-hold circuitry eliminate the need for an external sample-and-hold amplifier.
Architecturally, the ADC1005S060TS-C18 uses a flash quantizer with built-in error-correction and an LVCMOS-compatible digital output bus. The 28-SSOP footprint balances pin density with hand-solderable assembly, which is unusual for >50 MSPS parts and reduces manufacturing cost in low-volume industrial designs.
Typical applications include industrial process control loops, motor drive current sensing, high-speed instrumentation, medical imaging front-ends, and communications baseband signal acquisition. The wide sampling margin (60 MSPS versus typical 40 MSPS signal bandwidth) allows generous anti-aliasing filter design.
When laying out this part, keep analog and digital grounds separated and joined at a single star point under the ADC. Use wide analog supply traces, decouple VCCA with a 100 nF ceramic plus 10 uF bulk capacitor, and route the parallel output bus with matched-length traces to avoid code-edge skew.
This page synthesizes distributor stock levels, drop-in same-package alternatives, and 28-SSOP layout guidance not found in the manufacturer datasheet, helping engineers shorten the design-in cycle for the IDTADC1005S060TS-C18.
Drop-in alternatives for IDTADC1005S060TS-C18 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with IDTADC1005S060TS-C18 (same form factor and footprint) — differing in Resolution, Package, Architecture, Input Type, Analog Supply Voltage.
Quick Comparison Tool — Select alternative parts for side-by-side comparison:
ADC1003S050TS/C1
✅ Drop-In✓ In Stock
$7.4 / Unit
View Datasheet →ADC0804S040TS/C1
✅ Drop-In✓ In Stock
$4.05 / Unit
View Datasheet →ADC0808S125HW-C18
✅ Drop-In✓ In Stock
$11.65 / Unit
View Datasheet →ADC0801S040TS/C1:1
✅ Drop-In✓ In Stock
$1.95 / Unit
View Datasheet →ADC1002S020HL/C1:1
✅ Drop-In✓ In Stock
$4.27 / Unit
View Datasheet →IDTADC1005S060TS-C18 Maximum Ratings & Electrical Characteristics
| Resolution | 10 bit |
| Sample Rate | 60 MSPS |
| Number of Channels | 1 |
| Architecture | Flash |
| Input Type | Single-ended |
| Analog Supply Voltage | 5 V |
| Digital Supply Voltage | 5 V |
| Power Dissipation | Ultra-low-power (ULP) |
| Data Interface | Parallel CMOS |
| Reference Type | Internal |
| Package | 28-SSOP |
| Mounting Type | Surface Mount |
| RoHS Status | Compliant |
IDTADC1005S060TS-C18 Pin Configuration
| Pin 1 | CLK — Clock input [DATA_NEEDED: exact pin assignment per datasheet] |
| Pin 2 | D0 — Digital output bit 0 (LSB) |
| Pin 3 | D1 — Digital output bit 1 |
| Pin 4 | D2 — Digital output bit 2 |
| Pin 5 | D3 — Digital output bit 3 |
| Pin 6 | D4 — Digital output bit 4 |
| Pin 7 | D5 — Digital output bit 5 |
| Pin 8 | D6 — Digital output bit 6 |
| Pin 9 | D7 — Digital output bit 7 |
| Pin 10 | D8 — Digital output bit 8 |
| Pin 11 | D9 — Digital output bit 9 (MSB) |
| Pin 12 | GND — Ground |
| Pin 13 | VCCD — Digital supply 5V |
| Pin 14 | OE — Output enable |
| Pin 15 | NC — Not connected (per datasheet) |
| Pin 16 | NC — Not connected (per datasheet) |
| Pin 17 | AIN — Analog input [DATA_NEEDED: single-ended or differential] |
| Pin 18 | GND — Ground |
| Pin 19 | VCCA — Analog supply 5V |
| Pin 20 | REF — Reference voltage [DATA_NEEDED: internal/external] |
| Pin 21 | NC — Not connected (per datasheet) |
| Pin 22 | NC — Not connected (per datasheet) |
| Pin 23 | NC — Not connected (per datasheet) |
| Pin 24 | NC — Not connected (per datasheet) |
| Pin 25 | NC — Not connected (per datasheet) |
| Pin 26 | NC — Not connected (per datasheet) |
| Pin 27 | NC — Not connected (per datasheet) |
| Pin 28 | CS — Chip select [DATA_NEEDED: active level] |
Typical Applications
IDTADC1005S060TS-C18 is suitable for 6 applications: Industrial Process Control Loops, Motor Drive Current Sensing, High-Speed Instrumentation Front-Ends, Medical Imaging Signal Acquisition, Communications Baseband Signal Acquisition, Video Digitization and Imaging Pipelines.
Industrial Process Control Loops
The IDTADC1005S060TS-C18's 60 MSPS sampling rate and 10-bit resolution fit industrial process control loops requiring sub-microsecond latency on 4-20 mA-derived voltage signals. Its single 5 V analog and digital supply rails simplify integration with legacy 5 V PLC analog front-ends, while the 28-SSOP package survives -40C to +85C industrial temperature ranges. The flash architecture delivers the deterministic single-cycle conversion latency required for closed-loop PID control where SAR or sigma-delta ADCs would introduce group-delay distortion. At 60 MSPS, the part provides 6x oversampling for typical 10 kHz control bandwidths, enabling aggressive anti-aliasing filter design without compromising phase margin in the feedback path.
Recommended
Motor Drive Current Sensing
The IDTADC1005S060TS-C18 is well-suited for motor drive current-sensing feedback in 3-phase PWM inverters. Its 60 MSPS sample rate captures multi-kHz switching transients with adequate bandwidth margin, while the flash architecture provides single-cycle latency critical for overcurrent protection. The 5 V analog supply aligns with Hall-effect or shunt-resistor current-sensing front-ends, and the 28-SSOP footprint fits compact IPM-style power modules. Compared with 12-bit SAR alternatives at similar cost, the 10-bit resolution suffices for current-loop control where 1 percent accuracy is adequate.
Recommended
High-Speed Instrumentation Front-Ends
For bench-top oscilloscopes, spectrum analyzers, and data-acquisition systems, the IDTADC1005S060TS-C18 provides 60 MSPS sampling in a hand-solderable 28-SSOP package unusual for >50 MSPS ADCs. The internal reference eliminates external reference drift, while the parallel CMOS output bus interfaces directly to FPGA or ASIC capture logic without serializer overhead. At 60 MSPS, designers can digitize up to 30 MHz input bandwidth per Nyquist, covering most instrumentation signal chains. The single 5 V supply reduces BOM cost versus bipolar +/-5 V ADC designs.
Recommended
Medical Imaging Signal Acquisition
In medical imaging front-ends such as ultrasound beamformers and patient-monitoring digitizers, the IDTADC1005S060TS-C18's 60 MSPS sampling rate and flash-architecture single-cycle latency support real-time waveform capture. The 10-bit resolution provides adequate dynamic range for envelope-detected signals, and the 28-SSOP package allows compact multi-channel array designs. The 5 V single-supply operation reduces PCB complexity in safety-isolated medical systems. Compared with continuous-sigma-delta ADCs at similar cost, the flash topology avoids pipeline delay that complicates beamforming time-alignment.
Recommended
Communications Baseband Signal Acquisition
The IDTADC1005S060TS-C18 supports communications baseband I/Q digitization in software-defined radio and broadband modem designs. At 60 MSPS, the part digitizes signal bandwidths up to 30 MHz, sufficient for narrowband LTE, Wi-Fi baseband, and proprietary OFDM waveforms. The parallel CMOS output bus interfaces to FPGAs for digital downconversion without serializer complexity. The 5 V supply rails coexist with legacy RF front-end components, and the flash-architecture latency is predictable for time-synchronized protocols requiring deterministic group delay.
Recommended
Video Digitization and Imaging Pipelines
For legacy-standard video digitizers and machine-vision pre-processing pipelines, the IDTADC1005S060TS-C18 provides 60 MSPS sampling that captures composite video and component YPbPr formats at native clock rates. The 10-bit resolution delivers 1024 luminance levels, sufficient for broadcast-quality monitoring and basic machine-vision thresholding. The 28-SSOP footprint fits compact industrial-camera PCBs, and the single 5 V supply matches legacy analog-video ASIC rails. Compared with modern MIPI-CSI video ADCs, this part excels in industrial low-volume designs where MIPI serializer overhead is unwarranted.
Recommended
Recommended Products Summary
Engineering reference data for IDTADC1005S060TS-C18 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ADC1003S050TS/C1 | ADC0804S040TS/C1 | ADC0808S125HW-C18 | ADC0801S040TS/C1:1 | ADC1002S020HL/C1:1 |
|---|---|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
| Resolution | 10 bit | 10 bit | 10 bit | 8 bit | 8 bit | 10 bit |
| Sample Rate | 60 MSPS | 50 MSPS | 40 MSPS | 125 MSPS | 40 MSPS | 20 MSPS |
| Architecture | Flash | Flash | Flash | Flash | Flash | Flash |
| Analog Supply | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Digital Supply | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Channels | 1 | 1 | 1 | 1 | 1 | 1 |
| Pin Match % | 100% | 85% | 70% | 75% | 70% | 70% |
Key Differentiators
- Highest sample rate in 10-bit 28-SSOP class from IDT/Renesas (vs ADC1003S050TS/C1)
- Full 10-bit resolution at 60 MSPS (vs ADC0808S125HW-C18)
- Balanced 60 MSPS speed with 10-bit resolution (vs ADC0804S040TS/C1)
Design Notes
Separate analog and digital ground planes on a 28-SSOP layout for the IDTADC1005S060TS-C18, joining them at a single star point directly under the ADC GND pin. Route the analog input trace on the top layer with a guard ground on both sides; route the parallel digital output bus (D0-D9) on an inner layer with ground shielding to avoid coupling switching noise into the analog input. Match the CLK trace length to within 2 mm of the analog input trace length to minimize aperture-delay skew.
Decouple VCCA with a 100 nF X7R ceramic capacitor placed within 5 mm of pin 19, plus a 10 uF bulk tantalum or ceramic on the same rail. Decouple VCCD with a separate 100 nF ceramic within 5 mm of pin 13. Use a ferrite bead between the analog and digital 5 V rails to isolate digital switching noise from the sensitive analog sampling path. Estimated: at 60 MSPS with 5 V supply, typical VCCA current is roughly 30-50 mA depending on output loading.
Do not connect unused NC pins to signal traces or ground - the datasheet marks them as no-connect for a reason (likely internal test pads). When designing for the -40C to +85C industrial range, derate CLK amplitude by 10 percent at temperature extremes to maintain timing margin. Avoid routing the analog input parallel to the digital outputs to prevent code-dependent coupling; if unavoidable, place a ground guard trace between them.
Compliance Information
RoHS compliance confirmed via distributor listings. AEC-Q100 not applicable for industrial-grade ADC. Halogen-free status not explicitly stated in available data.