Texas Instruments

INA122PAG4 - Low-Power Instrumentation Amplifier | Texas Instruments

MPN: INA122PAG4 ✓ Active
MOQ: 1 |

INA122PAG4 Overview

The Texas Instruments INA122PAG4 is a single-supply, micropower precision instrumentation amplifier designed for accurate differential-signal acquisition. It operates from 2.2 V to 36 V, consumes approximately 60 µA of quiescent current, and is offered in an 8-pin PDIP package. The two-op-amp architecture provides a high-impedance differential input suitable for sensors, transducers, and low-level bridge signals.

An instrumentation amplifier is a specialized amplifier that amplifies the voltage difference between two inputs while rejecting signals common to both inputs. Its internal resistor arrangement and two-op-amp topology provide accurate gain control, low offset voltage, and strong common-mode rejection. The INA122 extends this architecture into a micropower package, making it particularly appropriate for portable medical instruments, battery-powered data-acquisition systems, and other low-power measurement equipment.

The INA122 can operate from either a single positive supply or dual supplies. Its 2.2 V minimum operating voltage supports low-voltage portable systems, while the 36 V maximum rating provides flexibility in industrial and instrumentation circuits. The approximately 60 µA quiescent current limits the static power requirement and helps conserve battery capacity when continuous signal acquisition is required.

Gain is set by an external resistor, allowing the circuit designer to select the sensitivity required for the sensor or measurement system. Because this is an instrumentation amplifier, input impedance remains high across the differential signal path, helping minimize loading of high-impedance sources. The device is intended for precision acquisition rather than high-speed waveform amplification, making it particularly suitable for slow sensor signals, strain-gauge bridges, biomedical instrumentation, and general-purpose data acquisition.

A practical design must keep input and output voltages within the device's operating limits and provide adequate bypassing around the supply pins. Input common-mode voltage and output swing are constrained by the selected supply configuration, so system-level headroom should be checked before scaling a sensor output. The external gain resistor should be located close to the gain-setting pin to limit parasitic resistance and preserve gain accuracy.

The INA122PAG4 is also suited to portable measurement systems where low quiescent current is more important than high bandwidth. Its compact 8-pin PDIP package is easy to prototype and inspect, making it useful for laboratory instruments, educational equipment, medical monitoring prototypes, and low-channel-count acquisition boards. This page combines the manufacturer specifications, package information, sourcing guidance, application guidance, and a practical comparison framework for engineers evaluating the INA122 and compatible instrumentation-amplifier options.

Drop-in alternatives for INA122PAG4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with INA122PAG4 (same form factor and footprint) — differing in Gain Range, Quiescent Current, Package, Architecture, Common-Mode Rejection Ratio.

Texas Instruments
Gain Range: 1 to 10,000 V/V
Quiescent Current: ±450 µA
Package: 8-pin plastic DIP
Compare with INA122PAG4 →
Texas Instruments
Gain Range: 5 V/V to 10,000 V/V
Quiescent Current: 60 uA
Package: 8-pin PDIP (P)
Compare with INA122PAG4 →
Texas Instruments
Gain Range: 1 V/V to 1000 V/V
Quiescent Current: 175 µA per channel
Package: 8-pin PDIP
Compare with INA122PAG4 →
Texas Instruments
Gain Range: 1 to 10,000
Quiescent Current: 700 µA
Package: 8-pin PDIP
Compare with INA122PAG4 →
Texas Instruments
Package: 8-pin plastic DIP
Compare with INA122PAG4 →

INA122PA

✅ Drop-In ⚠️ Specs Unverified
Texas Instruments
📦 8-pin PDIP
Instrumentation amplifier, two-op-amp design · 1 · 2.2 V to 36 V · +/-18 V · 60 uA · 250 uV · 3 uV/degC · 90 dB

Contact for price

View Datasheet →

INA121PA

✅ Drop-In ⚠️ Specs Unverified
Texas Instruments
📦 8-pin PDIP
Instrumentation amplifier · 1 circuit · ±4 pA · ±450 µA · ±200 µV · ±2 µV/°C · 100 nV/√Hz · 106 dB

Contact for price

View Datasheet →

INA126PA

✅ Drop-In ⚠️ Specs Unverified
Texas Instruments
📦 8-pin PDIP
Single-channel precision instrumentation amplifier · 36 V · ±1.35 V to ±18 V · 2.7 V · 175 µA per channel · 250 µV · Two-operating-amplifier instrumentation amplifier · 1 V/V to 1000 V/V

Contact for price

View Datasheet →

INA128PA

✅ Drop-In ⚠️ Specs Unverified
Texas Instruments
📦 8-pin PDIP
Precision instrumentation amplifier · Three-op-amp instrumentation amplifier · 1 circuit · 8-pin PDIP · 130 dB · 120 dB · 700 µA · 50 µV

Contact for price

View Datasheet →

INA129PA

✅ Drop-In ⚠️ Specs Unverified
Texas Instruments
📦 8-pin PDIP
Precision, low-power instrumentation amplifier · 1 circuit · 50 uV · 0.5 uV/degC · 5 nA · 120 dB · -40 V to +40 V · Plus or minus 18 V

Contact for price

View Datasheet →

INA122PAG4 Maximum Ratings & Electrical Characteristics

No specifications available

INA122PAG4 standard Pin Configuration Guide

Pin configuration for INA122PAG4 (standard package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

standard package pinout diagram for INA122PAG4

No detailed pinout data available for INA122PAG4.

Refer to the datasheet for full pin configuration.

Typical Applications

INA122PAG4 is suitable for 6 applications: Portable Medical Signal Acquisition, Battery-Powered Data Acquisition, Strain-Gauge Bridge Measurement, Industrial Sensor Interface, Low-Level Voltage Measurement, Portable Test and Measurement Instrument.

💊

Portable Medical Signal Acquisition

The INA122PAG4 fits portable medical monitoring equipment that acquires low-level differential sensor signals under strict power constraints. Its approximately 60 µA quiescent current minimizes the static burden imposed by the amplifier, while operation from 2.2 V supports compact battery-powered systems. The two-op-amp differential architecture can acquire physiological or diagnostic signals with high input impedance, reducing loading on sensitive transducers. Design the input network around the sensor's common-mode voltage and confirm the required output swing before choosing the external gain resistor. Single-supply operation is especially useful when the system must operate near zero volts, although safety, isolation, and regulatory requirements remain system-level considerations.

🧩

Battery-Powered Data Acquisition

The INA122PAG4 is appropriate for multichannel or multiplexed data-acquisition systems in which each measurement path must conserve power. The approximately 60 µA quiescent current is a central benefit because the amplifier can remain present in a portable acquisition chain without dominating the power budget. A 2.2 V minimum operating voltage also allows direct compatibility with low-energy system rails. Use the external gain resistor to establish the required signal scaling, and place the device where sensor traces can remain short. The INA122 is optimized for precision, low-bandwidth measurement rather than high-speed sampling, so anti-aliasing and channel-switching effects should be included in the complete acquisition design.

🏭

Strain-Gauge Bridge Measurement

The INA122PAG4 can amplify the small differential output of a strain-gauge bridge while rejecting common-mode voltage and electrical disturbances that affect both bridge inputs. Its differential-input architecture preserves measurement quality when the source impedance is relatively high, while the 2.2 V to 36 V supply range supports multiple instrumentation systems. External gain selection allows the circuit to be matched to the bridge sensitivity and excitation voltage. The bridge excitation itself should be referenced to the same system ground strategy to prevent excessive common-mode voltage. Because the INA122 is intended for precision acquisition, thermal drift, offset, gain error, and input bias effects must be included in the overall measurement uncertainty.

🏭

Industrial Sensor Interface

The INA122PAG4 is useful at the front end of industrial sensor interfaces that convert low-level differential outputs into a voltage suitable for an ADC or controller. The high-input-impedance instrumentation-amplifier topology minimizes loading, and the broad 2.2 V to 36 V supply range accommodates both compact sensors and higher-voltage instrumentation interfaces. The approximately 60 µA quiescent current is valuable in remote or distributed monitoring equipment where power is constrained. Designers should check the input common-mode range against the sensor's output, verify headroom at the amplifier output, and use supply bypassing close to the package. Protection structures may also be needed when sensor wiring is long or exposed to industrial transients.

🔧

Low-Level Voltage Measurement

The INA122PAG4 is suited to precision measurement of small differential voltages where a conventional single-ended amplifier would be sensitive to ground offsets or common-mode disturbances. Its two-op-amp instrumentation-amplifier configuration supports accurate gain setting with one external resistor and maintains balanced differential inputs. The low 60 µA quiescent current allows continuous monitoring from battery or energy-harvested systems. In implementation, verify that the input and output remain inside the datasheet limits at every process, temperature, and load condition. Keeping the gain resistor and input traces compact helps reduce sensitivity to parasitic resistance and unwanted pickup, particularly in low-level signals where microvolt-scale variations can affect the result.

🔧

Portable Test and Measurement Instrument

The INA122PAG4 supports handheld and laboratory measurement products that combine precision signal conditioning with low power consumption. Its 8-pin PDIP package is straightforward to prototype, troubleshoot, and replace in educational or instrumentation hardware. The approximately 60 µA quiescent current helps extend operating time in battery-assisted instruments, while operation down to 2.2 V supports compact mixed-signal designs. The amplifier can condition differential sensor, transducer, or test-probe signals before conversion by an ADC. Gain must be chosen to keep the output within its swing range, and common-mode voltage must remain valid at both power-up and overload. The resulting circuit should also include protection appropriate to the probe connection and environment.

What is the INA122PAG4 instrumentation amplifier?
The INA122PAG4 is a single-supply, micropower precision instrumentation amplifier from Texas Instruments. According to the Texas Instruments INA122 datasheet, it uses a two-op-amp design, accepts single or dual supplies from 2.2 V to 36 V, and has approximately 60 µA of quiescent current. The device is packaged in an 8-pin PDIP and is intended for portable instrumentation and data-acquisition systems.
What is the operating voltage range of INA122PAG4?
The INA122PAG4 operates from 2.2 V to 36 V. The Texas Instruments INA122 datasheet identifies both single-supply and dual-supply operation across this range. The 2.2 V lower limit suits compact battery-powered equipment, while the 36 V upper limit provides headroom for higher-voltage instrumentation circuits. Output and input common-mode limits still require separate design checks.
How much current does INA122PAG4 consume?
The INA122PAG4 has approximately 60 µA of quiescent current. According to the Texas Instruments INA122 datasheet, this micropower operating current is a principal feature for portable medical and data-acquisition equipment. The value describes the device's static current requirement; total circuit consumption also depends on load current, resistor selection, and the current drawn by associated support components.
Where can I download the INA122PAG4 datasheet PDF?
The official INA122PAG4 datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ina122.pdf. It is the appropriate document for pin assignments, electrical characteristics, gain-setting guidance, supply limits, and recommended application circuits. The device's 8-pin PDIP package and gain configuration should be checked against the package drawings and connection diagrams in that document.
Where can I find the INA122PAG4 pinout?
The INA122PAG4 pin assignments are shown in the manufacturer datasheet at https://www.ti.com/lit/ds/symlink/ina122.pdf. Use the pin-configuration table and the 8-pin PDIP outline when assigning PCB tracks. The INA122PAG4 combines input, output, supply, reference, and gain-setting functions in an 8-pin through-hole package, so tracing every signal from the datasheet before layout is essential.
Is the INA122PAG4 suitable for battery-powered medical instruments?
Yes, the INA122PAG4 is suitable for battery-powered medical instrumentation because its approximately 60 µA quiescent current and 2.2 V minimum supply support low-power operation. The Texas Instruments product page identifies portable medical and data-acquisition applications as core uses. The exact configuration must also satisfy the application's input-range, output-swing, safety, and regulatory requirements.
Where can I buy INA122PAG4 and check its lead time?
Use the Request a Quote form on this page to inquire about INA122PAG4 availability, unit pricing, minimum order quantity, and current lead time. The component is a catalog 8-pin PDIP instrumentation amplifier from Texas Instruments, and procurement should specify the exact INA122PAG4 suffix to avoid ordering a different package or gain option.
What is the current price of INA122PAG4?
The current commercial price for INA122PAG4 should be obtained through the Request a Quote form on this page. Quotations are tied to order quantity, inventory, packaging, and current procurement conditions. Use the full manufacturer part number INA122PAG4 when requesting a quotation so that the quote corresponds to the 8-pin PDIP configuration.
Is INA122PAG4 in stock?
Inventory status and current stock should be confirmed through the Request a Quote form on this page. Texas Instruments lists INA122 as an active low-power instrumentation amplifier, but market availability can change by package, order quantity, and shipment destination. The quote request should state the required quantity and delivery location for a current allocation response.
What can replace INA122PAG4?
The closest replacement is the INA122PA when an 8-pin PDIP configuration is required, because it belongs to the same INA122 family and shares the package format. Other instrumentation amplifiers can serve similar functions, but a valid drop-in replacement must match the 8-pin pinout, supply range, gain-setting method, input range, output swing, and accuracy requirements. Compare those functions in the manufacturer pin-configuration tables before substitution.
What is the best drop-in replacement for INA122PAG4?
INA122PA is the leading same-family drop-in candidate for INA122PAG4 because both are 8-pin PDIP INA122 options. The INA122 family is identified as a single-supply, micropower instrumentation amplifier with a 2.2 V to 36 V operating range and approximately 60 µA quiescent current. Confirm ordering suffixes, pin assignments, electrical limits, and lifecycle status before approving the substitution.
Is INA122PAG4 the same as INA121PA?
No. INA122PAG4 and INA121PA are related precision instrumentation amplifiers, but they are not automatically interchangeable. INA122 has a specified 2.2 V to 36 V operating range, approximately 60 µA quiescent current, and a two-op-amp architecture. INA121 has its own supply, gain, accuracy, and common-mode performance specifications, so an existing PCB must be checked pin by pin.
INA122PAG4 vs INA126PA — which is better for low-power sensing?
INA122PAG4 is the more direct choice when low power is the primary requirement, because the Texas Instruments INA122 datasheet specifies approximately 60 µA quiescent current. INA126PA may offer different gain, bandwidth, and accuracy characteristics that can be advantageous in other applications. The correct decision depends on sensor output range, required gain, bandwidth, supply voltage, and output-swing requirements.
When should I choose INA122PAG4 over INA128PA?
Choose INA122PAG4 when micropower operation and a 2.2 V minimum supply are central requirements, particularly in portable medical or battery-operated data-acquisition equipment. INA128PA may be preferable when its higher-current capability and different gain architecture fit the design better. Compare quiescent current, supply range, input common-mode range, gain accuracy, bandwidth, and package pin functions against the application.
What are the key specifications of INA122PAG4 for engineers?
The key INA122PAG4 specifications are a 2.2 V to 36 V supply range, approximately 60 µA quiescent current, a two-op-amp architecture, differential inputs, externally resistor-set gain, and an 8-pin PDIP package. Texas Instruments identifies the INA122 as a precision, low-noise solution for portable instrumentation and data acquisition. The datasheet should be used for gain error, offset, noise, bandwidth, and common-mode limits.

Engineering reference data for INA122PAG4 — comparison, design guidance, and compliance information.

Selection Guide

Choose INA122PAG4 for portable or battery-powered differential-signal measurement when low quiescent current, a 2.2 V minimum supply, and support for voltages up to 36 V are important. It is well suited to medical monitoring, strain-gauge bridges, and precision data-acquisition inputs that do not require high bandwidth. INA122PA is the most direct same-family alternative because it retains the 8-pin PDIP format and core INA122 architecture, but the exact suffix and electrical limits should be checked. Consider INA121PA when its precision characteristics better match the application, INA126PA when its gain and bandwidth behavior offers a better fit, and INA128PA or INA129PA when their current handling or gain architecture is advantageous. None should be substituted solely because it uses an 8-pin PDIP package; verify pin functions, input common-mode range, output swing, gain settings, supply limits, and lifecycle status.

Comparison with Alternatives

Parameter This Product INA122PA INA121PA INA126PA INA128PA INA129PA
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Mounting Type Through-hole PDIP Through-hole PDIP Through-hole PDIP Through-hole PDIP Through-hole PDIP Through-hole PDIP

Key Differentiators

  • Lowest-power option among the listed same-package family choices (vs INA128PA)
  • Broader stated supply capability than low-voltage instrumentation-amplifier alternatives (vs INA121PA)
  • Direct same-family package option for prototype and replacement planning (vs INA122PA)
  • Low-power differential acquisition with external gain control (vs INA129PA)

Design Notes

Place the external gain-setting resistor close to the corresponding INA122 gain pin and keep differential input traces short and symmetrical. Long, mismatched traces can add parasitic capacitance, pickup, and effective resistance that disturb gain accuracy. Route inputs away from switching-converter nodes and high-current return paths. For a differential sensor, maintain similar geometry and grounding on both input branches whenever practical.

Check input common-mode voltage and output swing against the supply configuration before selecting the gain. The INA122 supports single- and dual-supply operation from 2.2 V to 36 V, but those supply limits do not permit every input or output voltage. Confirm that the sensor can remain within the common-mode range at minimum and maximum conditions and that the amplified output retains headroom for the ADC input range.

Do not assume that an 8-pin PDIP package alone guarantees interchangeability. Although the listed alternatives share the same package format, gain-setting pins, supply limits, common-mode range, offset, gain accuracy, and output behavior can differ. Compare the manufacturer pin-configuration and electrical-characteristics tables before substituting a part, and verify the exact ordering suffix used in the original bill of materials.

Decouple the supply pins near the package with the capacitance and layout recommended in the Texas Instruments INA122 datasheet. Keep the switching loop of any upstream converter physically separated from the input and reference connections. In a portable design, the INA122's approximately 60 µA quiescent current helps reduce static demand, but total power also depends on sensor current, output load, reference circuitry, and conversion electronics.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

Compliance status was not established for this exact ordering code. Review the manufacturer product page, material declaration, and current quality documentation before making a compliance claim.

Related Searches

INA122PAG4 datasheet INA122PAG4 pinout INA122PAG4 datasheet pdf INA122PAG4 equivalent INA122PAG4 replacement INA122PAG4 cross reference INA122PAG4 price INA122PAG4 stock Texas Instruments INA122PAG4 INA122PAG4 60uA instrumentation amplifier INA122PAG4 8-PDIP INA122PAG4 medical signal acquisition INA122PAG4 vs INA122PA INA122PAG4 application circuit

Related Components & Terms

Texas Instruments INA122PAG4 INA122PA INA121PA INA126PA INA128PA INA129PA instrumentation amplifier precision instrumentation amplifier signal-conditioning IC amplifier IC integrated circuit semiconductor two-op-amp architecture differential input differential signal acquisition single-supply operation dual-supply operation 2.2 V to 36 V operating range 60 µA quiescent current external gain-setting resistor common-mode rejection 8-pin PDIP PDIP package family through-hole mounting portable medical instrumentation data-acquisition system strain-gauge bridge industrial sensor interface portable test and measurement
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details