LM2902QT14-13 - 36V Quad Op Amp, 14-TSSOP | Diodes Incorporated
MPN: LM2902QT14-13 ✓ ActiveLM2902QT14-13 Overview
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. High-gain feedback structures make the op amp useful for voltage followers, buffers, transimpedance amplifiers, comparators, differential stages, and analog signal conditioning. Within the electronic-component hierarchy, the LM2902 is a quad operational-amplifier IC: four amplifiers share one package while retaining independent input and output stages.
The four independent circuits allow a compact design to implement several analog functions without using four separate packages. Key characteristics include a typical unity-gain bandwidth of 1 MHz, 100 dB typical open-loop gain, 20 nA typical input bias current, and 700 µA typical supply current. These values make the device suitable for general-purpose industrial and automotive signal-conditioning circuits where moderate bandwidth and low quiescent consumption are more important than high-speed performance.
The LM2902 family uses a high-voltage internal design intended for supply rails approaching 36 V. Its low input bias current reduces the error introduced when the op amp drives high-impedance sensors or resistor networks. The 1 MHz unity-gain bandwidth supports closed-loop operation at substantially lower frequencies, with practical bandwidth determined by amplifier gain, noise, slew rate, and stability requirements. Four amplifier sections also permit independent gain stages within one package.
Typical applications include sensor-signal conditioning, 4–20 mA loop receivers, industrial instrumentation, automotive signal conditioning, transducer interfaces, active filters, and low-frequency control systems. The 14-pin TSSOP package helps reduce PCB area, although exposed thermal and decoupling considerations remain important in multi-amplifier designs.
For PCB implementation, place the supply bypass capacitor close to the positive and negative supply pins and route each amplifier's feedback components close to its assigned pins. Check output-current limits, input common-mode range, output swing, and the required output-voltage headroom against the specific supply voltage before finalizing the circuit.
This page combines the key LM2902QT14-13 characteristics, package information, application guidance, and a qualified comparison framework to help engineers evaluate this 36 V quad operational amplifier for new and existing analog designs.
Drop-in alternatives for LM2902QT14-13 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesLM2902QT14-13 Maximum Ratings & Electrical Characteristics
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 4 circuits |
| Maximum Supply Voltage | 36 V |
| Typical Supply Current | 700 µA |
| Typical Input Bias Current | 20 nA |
| Typical Open-Loop Gain | 100 dB |
| Typical Unity-Gain Bandwidth | 1 MHz |
| Package | 14-pin TSSOP |
| Mounting Type | Surface mount |
| Automotive Compliance | Automotive compliant |
LM2902QT14-13 Pin Configuration
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | IN1- — Amplifier 1 inverting input |
| Pin 3 | IN1+ — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | IN2+ — Amplifier 2 non-inverting input |
| Pin 6 | IN2- — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | OUT3 — Amplifier 3 output |
| Pin 9 | IN3- — Amplifier 3 inverting input |
| Pin 10 | IN3+ — Amplifier 3 non-inverting input |
| Pin 11 | V+ — Positive supply connection |
| Pin 12 | IN4+ — Amplifier 4 non-inverting input |
| Pin 13 | IN4- — Amplifier 4 inverting input |
| Pin 14 | OUT4 — Amplifier 4 output |
Typical Applications
LM2902QT14-13 is suitable for 6 applications: Automotive Sensor Signal Conditioning, Industrial Instrumentation Front End, 4-20 mA Loop Receiver, Transducer Interface Amplifier, Active Audio and Control Filter, Low-Frequency Power-Supply Feedback.
Automotive Sensor Signal Conditioning
The LM2902QT14-13 fits automotive sensor-conditioning circuits that need several amplified signals on one board. Its four independent amplifier sections can support low-side sensor amplification, signal buffering, threshold conditioning, and active filtering without requiring four separate packages. The manufacturer identifies the device as automotive compliant, while its 36 V maximum supply supports headroom for automotive battery-connected systems. Its 20 nA typical input bias current is useful with high-impedance sensors, and 1 MHz unity-gain bandwidth is adequate for many low-to-moderate-bandwidth channels. Confirm the exact temperature grade, common-mode range, output swing, and AEC-Q100 status before production release.
Recommended
Industrial Instrumentation Front End
The LM2902QT14-13 can condition several low-frequency industrial inputs in one compact 14-pin TSSOP package. Its 36 V maximum supply rating provides useful voltage-range flexibility for circuits connected to higher-voltage process equipment, while the typical 700 µA supply current keeps consumption moderate. Individual amplifier sections can implement instrumentation stages, buffers, active filters, or comparator-style functions around sensors. The 1 MHz typical unity-gain bandwidth is suitable for slow sensor signals rather than high-speed data acquisition. Confirm input bias requirements, output swing, and ground-reference arrangements against the exact electrical-characteristics table.
Recommended
4-20 mA Loop Receiver
A 4–20 mA receiver can use one LM2902QT14-13 section for input amplification and additional sections for filtering, buffering, or reference stages. The device's 20 nA typical input bias current helps reduce loading errors in high-impedance receiver networks, and its high open-loop gain of 100 dB supports accurate closed-loop signal conditioning. Its 36 V maximum supply rating provides useful compliance headroom when the receiver interface is exposed to industrial transients. The 1 MHz bandwidth is more than adequate for typical process-control loop rates. Validate the input common-mode range, maximum differential input, and output-swing limits before selecting the external resistor values.
Recommended
Transducer Interface Amplifier
The LM2902QT14-13 is suitable for low-frequency transducer interfaces requiring multiple buffered or amplified channels. Its four independent sections allow designers to combine a sensor input stage, gain stage, output driver, and auxiliary buffer in one package. The 20 nA typical input bias current limits the current drawn through high-value sensor resistors, which is important when preserving measurement accuracy. The 36 V supply capability also allows operation from higher-voltage industrial rails, subject to the common-mode and output-swing specifications. For strain gauges, thermistors, or capacitive sensors, check the sensor's output range against the amplifier's allowable input range and use an appropriate low-noise resistor network.
Recommended
Active Audio and Control Filter
The four amplifier sections in the LM2902QT14-13 can implement active filtering, gain, and buffering for low-frequency audio or industrial control signals. A typical unity-gain bandwidth of 1 MHz provides adequate loop gain for many sub-audio-band and control-loop filters, although exact response and stability depend on the selected topology. The general-purpose design also allows different sections to perform different tasks, reducing the need for multiple amplifier packages. Keep the operating points within the specified input and output ranges, and use the manufacturer's recommended compensation or feedback arrangements for each amplifier configuration. Avoid using it as a wide-band audio line driver without checking slew rate and output-current capability.
Recommended
Low-Frequency Power-Supply Feedback
The LM2902QT14-13 can provide error amplification, soft-start control, or output monitoring around a low-frequency power-conversion stage. Its 100 dB typical open-loop gain supports accurate closed-loop regulation, while the 36 V maximum supply permits operation in higher-voltage industrial systems. The four sections can monitor input and output conditions, amplify a current-sense signal, or buffer a control reference. Because the device is not a dedicated power-control IC, its thermal dissipation, output swing, and stability must be evaluated under worst-case conditions. Place decoupling capacitors near the supply pins and keep feedback routing short to avoid introducing oscillation into the outer supply loop.
Recommended
Engineering reference data for LM2902QT14-13 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Product Type | Quad general-purpose operational amplifier |
| Brand | Diodes Incorporated |
| Package | 14-pin TSSOP |
| Number of Amplifiers | 4 circuits |
| Maximum Supply Voltage | 36 V |
| Typical Supply Current | 700 µA |
| Typical Input Bias Current | 20 nA |
| Typical Open-Loop Gain | 100 dB |
| Typical Unity-Gain Bandwidth | 1 MHz |
| Automotive Compliance | Automotive compliant |
Key Differentiators
- Four independent amplifiers in one 14-pin TSSOP (vs LM324)
- High-voltage supply capability (vs LM324)
- Automotive-compliant ordering option (vs Generic LM2902 variants)
- Low input bias for impedance-sensitive circuits (vs General-purpose dual op amps)
Design Notes
Place the positive and negative supply-bypass capacitors directly beside the LM2902QT14-13 supply pins, and keep amplifier feedback resistors and compensation components close to their associated amplifier pins. Each of the four sections is independent, so short signal paths around every channel are more valuable than routing a shared signal through the entire package. Observe the pin-1 orientation and follow the manufacturer's land pattern and paste recommendations for the 14-pin TSSOP.
Validate the actual input common-mode range and output swing at the selected supply voltage before finalizing external resistor values. The 36 V maximum supply describes the device's upper operating limit, not permission to apply an arbitrary signal to any input pin. Check maximum differential input voltage, output-current demand, and common-mode behavior under transient conditions. Add input protection where external wiring can expose the circuit to industrial or automotive surges.
Do not treat every quad op amp with a 14-pin body as a drop-in replacement. Verify channel ordering, supply-pin locations, input polarity, output behavior, offset voltage, bias current, bandwidth, slew rate, and common-mode limits. The LM2902 family is widely used, but package and ordering suffixes can change qualification and temperature coverage. Confirm the exact MPN and pin description before approving a substitution.
Evaluate heat dissipation from the total load current drawn by all four amplifier sections and from power dissipated in any output stage carrying a large voltage difference. The 14-pin TSSOP has limited exposed heat-dissipation area, and the standard operating temperature range is not established by the available product listing. Use the manufacturer's thermal information for the exact ordering code and consider copper spreading where continuous output loading or high ambient temperature is expected.
Compliance Information
The Diodes Incorporated datasheet listing identifies LM2902QT14-13 as automotive compliant. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer ordering or compliance documentation.