LM293DR2G - Dual 36V Comparator | onsemi | Signal Control
MPN: LM293DR2G ✓ ActiveLM293DR2G Overview
A voltage comparator is an analog signal-conditioning device that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. Within the broader hierarchy of semiconductor components, the LM293DR2G belongs to the comparator category, analog signal-conditioning ICs, and power-management-adjacent control devices. Its two independent channels allow one package to perform two comparisons while sharing a common supply and ground.
The principal operating characteristics include a 2 V to 36 V supply range, a 1.3 µs response time, and a dual open-collector output architecture. The output structure can sink useful load current and requires an appropriate pull-up arrangement when driving subsequent digital stages. According to the onsemi LM293 family information, input offset voltage can be as low as 2.0 mV, while the LM293 series is designed for common-mode input operation down to ground with single-supply operation.
Each internal channel has differential inputs and an independently controlled output. Separate inputs allow the circuit designer to define the polarity of each decision, while separate output stages provide isolation between the two comparator functions. The 8-pin SOIC package supports conventional surface-mount assembly, but exposed-pad thermal management is not part of this package. Exact offset-voltage limits, input bias current, output-current limits, and channel-matching figures should be selected from the ordering information for the exact grade.
Typical uses include industrial sensor thresholds, motor and actuator control, power-supply monitoring, window or level detection, and general signal conditioning. In these systems, the comparator converts an analog relationship between two voltages into a logic-compatible indication that downstream control logic can process. The 36 V maximum supply capability is especially useful when the sensing circuit operates from an industrial bus rather than a low-voltage logic rail.
For dependable operation, treat each open-drain output as requiring a pull-up to the supply used by the receiving logic. Keep input and feedback traces short, provide a local supply bypass capacitor, and confirm that input voltages remain within the applicable common-mode and absolute-maximum limits. Account for output rise time after the pull-up resistor is added because the stated 1.3 µs response describes comparator propagation behavior, not the complete RC-controlled transition at the output node.
This product record combines the manufacturer family description with package, supply, temperature, and response-time details, then adds application guidance, pin-level implementation notes, and same-footprint comparison choices. These engineering views help designers evaluate the LM293DR2G as a dual comparator rather than treating it only as an eight-pin logic IC.
Drop-in alternatives for LM293DR2G — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM293DR2G (same form factor and footprint) — differing in Common-Mode Input Range, Comparator Type, Response Time, Output Type, Package.
LM393DR2G
✅ Drop-InContact for price
View Datasheet →LM2903DR2G
✅ Drop-InContact for price
View Datasheet →LM293DR
✅ Drop-InContact for price
View Datasheet →LM393DR
✅ Drop-In✓ In Stock
$0.11 / Unit
View Datasheet →LM2903DR
✅ Drop-InContact for price
View Datasheet →LM293DR2G Maximum Ratings & Electrical Characteristics
| Comparator Type | Dual precision voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Response Time | 1.3 µs |
| Output Type | Open-collector, open-drain |
| Common-Mode Input Range | Includes ground with single-supply operation |
| Input Offset Voltage | As low as 2.0 mV for the LM293 series |
| Operating Temperature | -25 °C to +85 °C |
| Package | 8-pin SOIC |
| Mounting Type | Surface mount |
| Channel Independence | 2 independent comparator channels |
| Supply Configuration | Single or split supply |
LM293DR2G Pin Configuration
| Pin 1 | OUT1 — Channel 1 open-collector, open-drain output |
| Pin 2 | IN1- — Channel 1 inverting input |
| Pin 3 | IN1+ — Channel 1 non-inverting input |
| Pin 4 | GND — Ground reference |
| Pin 5 | IN2+ — Channel 2 non-inverting input |
| Pin 6 | IN2- — Channel 2 inverting input |
| Pin 7 | OUT2 — Channel 2 open-collector, open-drain output |
| Pin 8 | VCC — Positive supply input |
Typical Applications
LM293DR2G is suitable for 6 applications: Industrial Sensor Threshold Detection, Motor and Actuator Control, Power-Supply Monitoring, Automotive and Battery System Interfaces, Consumer and IoT Condition Detection, Analog Signal Conditioning.
Industrial Sensor Threshold Detection
The LM293DR2G fits industrial threshold detection because its two independent channels can compare a conditioned sensor voltage against independent reference or limit voltages. Its 2 V to 36 V operating range supports compatibility with higher-voltage sensing and control environments, while the 1.3 µs response time allows rapid state transitions. Each open-drain output requires a pull-up to the logic rail. Place the pull-up close to the comparator, bypass the supply locally, and keep sensor and reference traces away from switching nodes to prevent false threshold crossings.
Recommended
Motor and Actuator Control
The LM293DR2G can serve as the decision element in motor and actuator control by comparing a command or feedback voltage with a reference threshold. Its 1.3 µs response time helps minimize actuation delay, and the dual-channel arrangement can supervise two independent conditions within one 8-pin SOIC package. Because the outputs are open-drain, an appropriate pull-up and driver-stage interface are required rather than direct connection to a high-current load. Keep inductive power paths separate from the comparator inputs to avoid switching transients at the threshold input.
Recommended
Power-Supply Monitoring
The LM293DR2G is appropriate for power-supply monitoring when a system must detect whether an analog rail has crossed a defined threshold. The 2 V to 36 V supply range accommodates monitoring of multiple industrial voltage classes, and the two channels can independently supervise positive and negative conditions. Its common-mode capability includes ground during single-supply operation, which supports low-side sensing. Use separate precision reference circuitry for accurate limits and ensure each open-drain output has a pull-up tied to the system’s valid logic level.
Recommended
Automotive and Battery System Interfaces
The LM293DR2G can be evaluated for battery-powered and automotive interface circuits that compare sensed voltages within a 2 V to 36 V range. Its dual channels reduce package count when two system conditions must be evaluated, and the 1.3 µs response time supports prompt fault indication. The listed temperature grade is -25 °C to +85 °C, so a part explicitly qualified for wider automotive temperature requirements may be necessary. Any adopted output driver must be compatible with the open-drain interface and vehicle electrical conditions.
Recommended
Consumer and IoT Condition Detection
The LM293DR2G is suitable for compact consumer or IoT modules that need to translate an analog condition into a digital signal, such as a level, window, or configuration threshold. Two independent comparator channels fit within one 8-pin SOIC package, and operation from a supply as low as 2 V supports embedded systems. The open-drain outputs can connect to a microcontroller input with a pull-up, but the resistor should be sized for the input’s leakage and logic-level requirements. Minimize input-node capacitance to preserve useful response speed.
Recommended
Analog Signal Conditioning
The LM293DR2G can convert a bipolar or unipolar analog signal into a logic indication when one input receives the signal and the other receives a reference. Its dual independent architecture supports two signal chains without requiring two packages, while common-mode operation down to ground helps simplify single-supply designs. The 1.3 µs response time is useful when the threshold must respond promptly, although the complete output edge also depends on pull-up resistance and input capacitance. Maintain adequate supply bypass and route feedback paths away from fast-switching circuitry.
Recommended
Recommended Products Summary
Engineering reference data for LM293DR2G — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM393DR2G | LM2903DR2G | LM293DR | LM393DR | LM2903DR |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
Key Differentiators
- Wide operating supply range (vs LM393DR2G)
- Two independent channels in one package (vs LM293DR)
- Open-drain output compatibility (vs LM2903DR)
Design Notes
Do not treat the 1.3 µs response time as the complete output transition time. The open-drain output changes state by sinking charge, while its rising edge is controlled by the pull-up resistor and total node capacitance. Choose the pull-up to meet the receiving logic’s rise-time requirement and place it close to the LM293DR2G output to limit parasitic capacitance.
Route the two differential input pairs as short, quiet traces and connect a local supply bypass capacitor from VCC to ground near pin 8. Keep switching-regulator, relay, and motor traces away from the input and reference nets. A solid ground plane helps establish the common reference, but input traces should still avoid areas containing high-di/dt currents.
Use separate reference and feedback paths, and avoid routing either input directly beside the open-drain output or pull-up node. Comparator inputs can respond to fast transients even when propagation delay is short. If the input source has high impedance, add a suitable bias network or guard area to limit leakage-induced error and maintain stable threshold behavior.
Compliance Information
Compliance status must be confirmed for the exact LM293DR2G ordering code and manufacturing site using the manufacturer’s compliance documentation.