Texas Instruments

MAX211IDBRG4 - 5V 120kbps RS-232 Transceiver | TI

MPN: MAX211IDBRG4 ✓ Active
5 V Vdss 1 µA typical Id 28-pin SSOP Package
MOQ: 1 |

MAX211IDBRG4 Overview

Texas Instruments MAX211IDBRG4 is a 5V multichannel RS-232 line driver and receiver with four drivers, five receivers, 120 kbit/s operation, and ±15 kV ESD protection, packaged in a 28-pin SSOP. It provides the electrical interface between an asynchronous communication controller and an RS-232 serial connector.

An RS-232 transceiver is an interface IC that converts logic-level UART signals into RS-232 differential voltage levels and converts received RS-232 signals back into logic-compatible levels. This signal-conditioning layer sits between a serial communication controller and an external connector. The MAX211 belongs to the broader RS-232 interface, transceiver, interface IC, and semiconductor hierarchy. Its integrated dual charge pump generates the positive and negative voltage levels required by RS-232 while allowing operation from a single 5V supply.

The device includes four RS-232 drivers, five RS-232 receivers, and pin-to-pin ESD protection rated at ±15 kV using the human-body model. It operates at up to 120 kbit/s and meets the requirements of TIA/EIA-232-F and ITU V.28, as identified in the manufacturer datasheet. An enable control supports low-power shutdown, while the low shutdown supply current helps suit equipment where the serial interface is not continuously active.

The dual charge-pump architecture is a key technical feature. Four small external capacitors support the charge-pump circuit, allowing the interface to produce the bipolar voltage swings needed for RS-232 communication. The four-driver and five-receiver arrangement supports applications requiring more receive channels than transmit channels, while the shared 5V supply simplifies interface implementation in industrial-control, test, and embedded systems.

Typical uses include multi-channel RS-232 port expansion, industrial data acquisition, service and configuration interfaces, legacy peripheral connectivity, and embedded control systems that retain a serial console. The industrial temperature range of −40°C to +85°C supports use across commercial and industrial environments where temperature variation is expected.

PCB design should preserve short charge-pump capacitor connections and provide adequate input and output return paths for every RS-232 channel. Place ESD-protection and signal-routing structures near the connector when the external cable creates a direct electrostatic-discharge path. Confirm signal polarity, receiver direction, enable state, and connector mapping before releasing a new layout.

This page combines the manufacturer’s electrical specifications, verified drop-in replacement information, application guidance, package details, and practical layout considerations to accelerate component selection and PCB implementation.

Drop-in alternatives for MAX211IDBRG4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with MAX211IDBRG4 (same form factor and footprint) — differing in Number of Drivers, Number of Receivers, Product Type, ITU Standard, Operating Temperature Range.

Texas Instruments
Number of Drivers: 4 channels
Number of Receivers: 5 channels
Product Type: 1 multichannel RS-232 line driver/receiver
Compare with MAX211IDBRG4 →
Texas Instruments
Number of Drivers: 4 drivers
Number of Receivers: 5 receivers
Product Type: 5 V multichannel RS-232 line driver/receiver
Compare with MAX211IDBRG4 →

MAX213EEAI+

✅ Drop-In
📦 28-pin SSOP
Same 28-pin SSOP and core 5 V, 120 kbit/s, four-driver, five-receiver RS-232 function; enable and secondary electrical details should be compared before substitution

📋 Reference alternative (not in catalog)

MAX211IDBRG4 Specifications

Product Type RS-232 line driver and receiver
Supply Voltage 5 V
Maximum Data Rate 120 kbit/s
Number of Drivers 4
Number of Receivers 5
Driver Output Voltage ±9 V
ESD Protection ±15 kV using the Human-Body Model
Operating Temperature Range −40°C to +85°C
Package 28-pin SSOP
Mounting Type Surface mount
Interface Standard TIA/EIA-232-F
ITU Standard ITU V.28
Charge-Pump Capacitors Required 4 external capacitors
Shutdown Supply Current 1 µA typical
Temperature Grade Industrial
Terminal Count 28 terminals

MAX211IDBRG4 28-pin ssop Pin Configuration Guide

Pin configuration for MAX211IDBRG4 (28-pin ssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

28-pin ssop package pinout diagram for MAX211IDBRG4

No detailed pinout data available for MAX211IDBRG4.

Refer to the datasheet for full pin configuration.

Typical Applications

MAX211IDBRG4 is suitable for 6 applications: Industrial RS-232 Port Expansion, Legacy Peripheral Connectivity, Data Acquisition and Control, Service and Configuration Port, Embedded Serial Console, Instrumentation and Test Equipment.

🏭

Industrial RS-232 Port Expansion

The MAX211IDBRG4 is appropriate for expanding a legacy asynchronous serial interface because it combines four drivers and five receivers with operation from a single 5 V supply. A controller can use the four transmitter channels for commands and configuration outputs while the five receiver channels monitor status, acknowledgments, or sensor data. Operation up to 120 kbit/s supports conventional industrial serial links. The −40°C to +85°C range also suits equipment operating across typical industrial temperature ranges, although system-level EMC and grounding remain important.

🔧

Legacy Peripheral Connectivity

The MAX211IDBRG4 provides the electrical interface required when a modern controller must communicate with a legacy RS-232 peripheral. Four drivers permit simultaneous command outputs, while five receivers allow multiple feedback or acknowledgment signals to be monitored. Its 120 kbit/s maximum data rate is appropriate for many legacy asynchronous peripherals. The integrated charge pump reduces the external support circuitry to four small capacitors, making the device suitable for compact industrial-control, instrument, and service-interface boards.

📊

Data Acquisition and Control

The four-driver, five-receiver configuration in the MAX211IDBRG4 fits acquisition systems that send commands while receiving measurements or equipment status. The interface can bridge a UART-capable controller to external sensors, programmable instruments, or remote I/O modules over RS-232. A maximum rate of 120 kbit/s accommodates many supervisory and configuration links, while the 5 V supply and four external charge-pump capacitors simplify integration near the logic circuitry.

🖥️

Service and Configuration Port

The MAX211IDBRG4 can implement a multi-signal service interface for equipment that requires more control or monitoring channels than a basic RS-232 port provides. Four transmit outputs and five receive inputs support commands, status flags, diagnostic outputs, and acknowledgments without requiring a separate transceiver for every direction. Its industrial temperature range supports use in deployed equipment, and the ±15 kV human-body-model ESD rating adds protection on exposed serial-port connection pins.

⚡

Embedded Serial Console

The MAX211IDBRG4 is suitable for an embedded system that must retain a wired RS-232 console alongside modern communications interfaces. The single 5 V operation aligns with conventional embedded logic supplies, and the integrated dual charge pump avoids a separate bipolar supply generator. The 28-pin SSOP places four drivers and five receivers in a compact surface-mount footprint. At 120 kbit/s, the device supports console traffic and other supervisory serial channels, subject to the connected equipment’s electrical and protocol requirements.

🔬

Instrumentation and Test Equipment

The MAX211IDBRG4 can connect an instrument controller to external RS-232 test equipment through several channels. Its five receivers are useful for acquiring ready, pass, fail, measurement, and remote-trigger signals, while four drivers can operate test stimuli or control devices. The device supports up to 120 kbit/s and operates across −40°C to +85°C. In instrument chassis applications, pair the interface with a suitable connector and chassis-ground strategy to maintain predictable ESD and signal-integrity behavior.

Recommended Products Summary

MAX211IDBR Texas Instruments Used in: Industrial RS-232 Port Expansion, Legacy Peripheral Connectivity, Data Acquisition and Control, Service and Configuration Port, Embedded Serial Console, Instrumentation and Test Equipment MAX213EEAI+ Pin-compatible RS-232 transceiver alternative Used in: Industrial RS-232 Port Expansion, Legacy Peripheral Connectivity, Data Acquisition and Control, Service and Configuration Port, Embedded Serial Console, Instrumentation and Test Equipment
What is the operating voltage of MAX211IDBRG4?
The MAX211IDBRG4 operates from a single 5 V supply. According to the Texas Instruments MAX211 datasheet, the integrated dual charge-pump circuit develops the positive and negative RS-232 voltage levels required by the interface from this supply. Four small external charge-pump capacitors are required. The device supports RS-232 communication rates up to 120 kbit/s and is intended for use with 5 V asynchronous communication controllers and standard serial connectors.
What are the key specifications of MAX211IDBRG4 that engineers should know?
The MAX211IDBRG4 is a 5 V multichannel RS-232 transceiver with four line drivers, five line receivers, 120 kbit/s operation, ±9 V driver outputs, and ±15 kV human-body-model ESD protection. It is packaged in a 28-pin SSOP and operates from −40°C to +85°C. The manufacturer datasheet identifies TIA/EIA-232-F and ITU V.28 compliance, while the dual charge-pump architecture requires four small external capacitors.
How many RS-232 drivers and receivers does MAX211IDBRG4 have?
The MAX211IDBRG4 contains four RS-232 line drivers and five RS-232 receivers. This asymmetrical channel count is useful when a system needs to receive more signals than it transmits, such as a multi-channel monitoring or configuration interface. Each driver provides approximately ±9 V RS-232 output levels, while each receiver converts an incoming RS-232 signal to a logic-level output for the host controller.
What is the maximum data rate of MAX211IDBRG4?
The MAX211IDBRG4 supports RS-232 data rates up to 120 kbit/s. According to the Texas Instruments MAX211 datasheet, the device meets the requirements of TIA/EIA-232-F and ITU V.28 while operating from a single 5 V supply. This rate is suitable for conventional asynchronous serial links, port expanders, legacy peripheral interfaces, and industrial control systems that do not require a higher-speed differential bus.
What ESD protection does MAX211IDBRG4 provide?
The MAX211IDBRG4 provides ±15 kV human-body-model ESD protection pin to pin on its serial-port connection pins, including ground. The Texas Instruments product information identifies this rating for the MAX211 family. This protection helps reduce electrostatic-discharge damage at an exposed serial connector, although cable routing, connector selection, chassis grounding, and additional board-level protection should still be evaluated for the final installation.
Where can I download the MAX211IDBRG4 datasheet PDF?
The official MAX211IDBRG4 datasheet PDF is available from Texas Instruments through the MAX211 product page and the direct manufacturer-datasheet link on this page. The document describes the four drivers, five receivers, dual charge pump, external capacitor connections, electrical characteristics, and ordering information. Use the manufacturer pin-description and typical-application sections when assigning PCB tracks and selecting external components.
Where can I find the MAX211IDBRG4 pinout?
The MAX211IDBRG4 pinout is defined in the pin-description section of the Texas Instruments MAX211 datasheet. The device uses a 28-pin SSOP with gull-wing leads. Use the numbered pin-description table when assigning driver outputs, receiver inputs and outputs, charge-pump capacitors, supply rails, enable control, and ground connections. The package drawing on this page identifies the 28-pin SSOP form factor, but individual signal names should be taken directly from the manufacturer document.
What is the best drop-in replacement for MAX211IDBRG4?
MAX213EEAI+ is the verified drop-in alternative for MAX211IDBRG4. The cross-reference information identifies it as a 28-pin SSOP RS-232 interface with consistent main performance characteristics and terminals, allowing replacement without changing the package or pin arrangement. Both devices operate at 5 V and support 120 kbit/s communication. Final substitution should still be checked against enable behavior, shutdown current, capacitance values, and production qualification requirements.
Can MAX213EEAI+ replace MAX211IDBRG4?
Yes, MAX213EEAI+ can replace MAX211IDBRG4 as a pin-compatible 28-pin SSOP RS-232 interface. The verified cross-reference describes the devices as having consistent terminal configurations and functional performance, including 5 V operation and 120 kbit/s RS-232 signaling. Engineers should nevertheless compare the manufacturer datasheets for receiver thresholds, charge-pump capacitor recommendations, enable timing, and shutdown current before approving a design change.
What can replace MAX211IDBRG4 in an RS-232 interface?
MAX213EEAI+ can replace MAX211IDBRG4 in a conventional RS-232 interface because it uses the same 28-pin SSOP format and is documented as completely replaceable in the verified cross-reference. The match covers the key 5 V, 120 kbit/s, four-driver, and five-receiver function. A production design should still verify enable polarity, charge-pump capacitor values, shutdown behavior, and the exact manufacturer ordering code before substitution.
Is MAX211IDBRG4 the same as MAX213EEAI+?
No, MAX211IDBRG4 and MAX213EEAI+ are different manufacturer part numbers, but they are documented as a pin-compatible replacement pair in the 28-pin SSOP format. Their principal RS-232 functions align at 5 V and 120 kbit/s with four drivers and five receivers. They should not be treated as identical in every secondary parameter, so review enable timing, shutdown current, capacitance recommendations, and qualification documents before substitution.
When should I choose MAX211IDBRG4 over MAX213EEAI+?
Choose MAX211IDBRG4 when the design is already qualified around the Texas Instruments MAX211 family, its documented 5 V operation, four drivers, five receivers, 120 kbit/s performance, and established charge-pump implementation. Choose MAX213EEAI+ when it provides a verified pin-compatible sourcing path and the secondary electrical characteristics meet the system requirements. Existing PCB layouts can generally be reused for either device after reviewing the relevant datasheet differences.
Is MAX211IDBRG4 suitable for industrial RS-232 equipment?
The MAX211IDBRG4 is suitable for many industrial RS-232 designs because it has an industrial operating-temperature range of −40°C to +85°C, four drivers, five receivers, and 120 kbit/s operation. Its ±15 kV human-body-model ESD protection adds useful robustness at a connector interface. Final suitability also depends on the enclosure, grounding strategy, cable exposure, electromagnetic environment, and production qualification requirements of the complete equipment.
Where can I buy MAX211IDBRG4 and check its current availability?
Use the Request a Quote form on this page to ask about MAX211IDBRG4 availability, current pricing, lot conditions, and lead time. The form provides the appropriate direct response for this order-on-request product without embedding prices that may change between visits. For technical validation, use the official Texas Instruments MAX211 product page and datasheet, then confirm the exact 28-pin SSOP ordering code before placing an order.
What is the lead time for MAX211IDBRG4?
The current lead time for MAX211IDBRG4 should be requested through the Request a Quote form on this page. Lead time can vary with the exact package suffix, quantity, lot availability, and manufacturing schedule. The manufacturer product page provides the ordering and quality information needed to identify the device correctly, while the quote form is the appropriate route for a current, quantity-specific delivery commitment.

Engineering reference data for MAX211IDBRG4 — comparison, design guidance, and compliance information.

Selection Guide

Choose MAX211IDBRG4 when a system needs a compact, single-supply RS-232 interface with four transmit channels, five receive channels, 120 kbit/s operation, and connection-pin ESD protection rated at ±15 kV using the human-body model. Its 28-pin SSOP package and four external charge-pump capacitors make it suitable for industrial, instrumentation, legacy peripheral, and embedded console designs. Choose MAX213EEAI+ when procurement needs a documented pin-compatible alternative in the same 28-pin SSOP format. Before substituting that part, compare enable timing, receiver thresholds, shutdown current, external capacitor recommendations, ESD ratings, and qualification requirements in the respective manufacturer datasheets. Neither option should be selected solely from package appearance: the existing board layout, connector mapping, operating temperature, and system grounding strategy must remain compatible with the final device revision.

Comparison with Alternatives

Parameter This Product MAX213EEAI+
Package 28-pin SSOP 28-pin SSOP
Brand Texas Instruments Maxim Integrated
Device Type Multichannel RS-232 line driver/receiver Multichannel RS-232 line driver/receiver
Supply Voltage 5 V 5 V
Maximum Data Rate 120 kbit/s 120 kbit/s
Number of Drivers 4 4
Number of Receivers 5 5

Key Differentiators

  • Matched four-driver and five-receiver configuration (vs MAX213EEAI+)
  • Single 5 V operating supply (vs MAX213EEAI+)
  • Connector-side ESD protection (vs MAX213EEAI+)

Design Notes

Place the four charge-pump capacitors close to their designated MAX211 pins and keep each capacitor connection short. These components carry repetitive charge-transfer current, so long loops can increase radiated emissions and susceptibility to noise. Route the charge-pump section away from sensitive receiver inputs and follow the manufacturer layout example. Use a continuous ground plane where practical, and connect the exposed environment through a controlled chassis and signal-ground strategy.

Assign every RS-232 driver output and receiver input according to the pin-description table in the manufacturer datasheet. Keep connector-side traces short, provide a nearby chassis entry point where applicable, and avoid routing sensitive receiver inputs beneath digital clocks or switching nodes. The five receiver channels should have independent return paths to minimize common-impedance coupling. Validate the final connector pinout, signal polarity, and multidrop restrictions before fabrication.

Do not treat the ±15 kV human-body-model ESD rating as protection for every installation method. The rating applies to the specified device pins and test model, not the complete connector or enclosure. External protection may still be needed for long field cables, outdoor equipment, or severe industrial environments. Also verify the enable state, charge-pump capacitor values, and external capacitor type and voltage rating against the manufacturer guidance before production release.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The MAX211 family is identified as an industrial-temperature RS-232 interface meeting TIA/EIA-232-F and ITU V.28. Specific material-compliance declarations are not stated and therefore remain unknown.

Data verified on: 2026-11-09 — data verified and curated by XAIPART's component engineering team

Related Searches

MAX211IDBRG4 datasheet MAX211IDBRG4 pinout MAX211IDBRG4 datasheet pdf MAX211IDBRG4 equivalent MAX211IDBRG4 replacement MAX211IDBRG4 cross reference MAX211IDBRG4 vs MAX213EEAI+ MAX211IDBRG4 120kbps interface MAX211IDBRG4 28-SSOP pinout MAX211IDBRG4 application circuit MAX211IDBRG4 price MAX211IDBRG4 stock Texas Instruments MAX211IDBRG4 what is MAX211IDBRG4

Related Components & Terms

Texas Instruments MAX211IDBRG4 MAX213EEAI+ Maxim Integrated RS-232 TIA/EIA-232-F ITU V.28 RS-232 transceiver line driver line receiver interface IC semiconductor dual charge pump 120 kbit/s 5 V ±15 kV ESD protection Human-Body Model 28-pin SSOP SSOP family surface mount industrial temperature grade asynchronous serial communication legacy peripheral industrial data acquisition
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details