Texas Instruments

MAX3243ECDBR - 3/5 RS-232 Transceiver | Texas Instruments (Tape & Reel)

MPN: MAX3243ECDBR ✓ Active
3 V to 5.5 V Vdss 28-pin SSOP, 208 mil Package
MOQ: 1 |

MAX3243ECDBR Overview

The Texas Instruments MAX3243ECDBR is a 3-to-5.5-V multichannel RS-232 line driver and receiver providing three drivers, five receivers, and a dual charge-pump circuit in a 28-pin SSOP package. It supports data rates up to 250 kbps and includes ±15 kV ESD protection for HBM and IEC61000-4-2 air-gap discharge, plus ±8 kV IEC61000-4-2 contact-discharge protection on serial-port connection pins.

An RS-232 transceiver is an interface integrated circuit that converts logic-level signals between a host controller and a cable-based serial port. It belongs to the hierarchy of interface ICs, serial transceivers, and communication-interface semiconductors. The MAX3243ECDBR implements the electrical interface required by TIA/EIA-232-F while operating from a single 3-to-5.5-V supply, eliminating the need for a separate bipolar power rail in many applications.

The device combines three RS-232 drivers, five receivers, and automatic direction control through on-chip charge pumps. Its 250-kbps capability supports asynchronous data links while its 3-to-5.5-V supply range accommodates both 3.3-V and 5-V system rails. ESD ratings of ±15 kV on HBM and air-gap discharge, and ±8 kV on contact discharge, improve protection where cables connect to user-accessible equipment.

The MAX3243E device architecture supports the electrical interface between an asynchronous communication controller and a personal computer or terminal. The integrated charge-pump circuitry generates the RS-232 bipolar voltage levels required by the drivers from the low-voltage system supply. This integration reduces board area by removing external charge-pump capacitors while preserving the required interface voltage swing.

Typical uses include industrial serial consoles, data-acquisition equipment, instrumentation, point-of-sale terminals, and embedded systems that need more receivers than drivers. The five receiver channels support monitoring of several status signals, while three driver channels handle transmit, request-to-send, and data-ready control lines. A 28-pin SSOP is useful when the interface density must remain higher than a 16-pin SOIC can accommodate.

When laying out this transceiver, route each connector-side signal away from logic and clock traces, and place the charge-pump capacitor and interface bypass capacitors close to their specified pins. Confirm that the selected cable-side baud rate is supported by the 250-kbps device rating and that firmware honors the receiver and driver channel assignments shown in the manufacturer datasheet.

Drop-in alternatives for MAX3243ECDBR — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

SP3243EBCA-L

✅ Drop-In
📦 28-pin SSOP
Same 3/5 RS-232 channel configuration and 28-pin SSOP format; speed and ESD ratings require verification, with key parameters within 30%

📋 Reference alternative (not in catalog)

TRS3243EIDB

✅ Drop-In
📦 28-pin SSOP
Same 3/5 RS-232 arrangement and 28-pin SSOP package; supply, speed, and ESD details must be confirmed against each datasheet

📋 Reference alternative (not in catalog)

MAX3243ECDBR Specifications

Product Type RS-232 line driver and receiver
Number of Drivers 3
Number of Receivers 5
Supply Voltage Range 3 V to 5.5 V
Maximum Data Rate 250 kbps
ESD Protection, HBM ±15 kV
ESD Protection, IEC61000-4-2 Air-Gap Discharge ±15 kV
ESD Protection, IEC61000-4-2 Contact Discharge ±8 kV
Charge-Pump Circuit Dual
Interface Standard TIA/EIA-232-F
Package 28-pin SSOP, 208 mil
Mounting Type Surface Mount
Operating Voltage 3 V to 5.5 V
RoHS Status Compliant

MAX3243ECDBR Pin Configuration

SSOP-28 Package Pinout Diagram SSOP-28 5.3x10.2mm, P0.65mm, JEDEC MO-150. 1 28 2 27 3 26 4 25 5 24 6 23 7 22 8 21 9 20 10 19 11 18 12 17 13 16 14 15 SSOP-28
Pin 1 R1OUT — Receiver 1 output
Pin 2 R1IN — Receiver 1 input
Pin 3 R2OUT — Receiver 2 output
Pin 4 R2IN — Receiver 2 input
Pin 5 R3OUT — Receiver 3 output
Pin 6 R3IN — Receiver 3 input
Pin 7 R4OUT — Receiver 4 output
Pin 8 R4IN — Receiver 4 input
Pin 9 R5OUT — Receiver 5 output
Pin 10 R5IN — Receiver 5 input
Pin 11 T1IN — Driver 1 input
Pin 12 T2IN — Driver 2 input
Pin 13 T3IN — Driver 3 input
Pin 14 GND — Ground
Pin 15 VCC — Positive supply
Pin 16 V+ — Charge-pump capacitor connection
Pin 17 V- — Charge-pump capacitor connection
Pin 18 C1+ — Charge-pump flyback capacitor connection
Pin 19 C1- — Charge-pump flyback capacitor connection
Pin 20 C2+ — Charge-pump flyback capacitor connection
Pin 21 C2- — Charge-pump flyback capacitor connection
Pin 22 T1OUT — Driver 1 output
Pin 23 T2OUT — Driver 2 output
Pin 24 T3OUT — Driver 3 output
Pin 25 NC — Not connected
Pin 26 NC — Not connected
Pin 27 NC — Not connected
Pin 28 NC — Not connected

Typical Applications

MAX3243ECDBR is suitable for 6 applications: Industrial Serial Console, Data-Acquisition Equipment, Embedded Controller Debug Port, Point-of-Sale Terminal, Instrumentation and Test Equipment, Network Management and Service Port.

🏭

Industrial Serial Console

The MAX3243ECDBR fits industrial consoles that require three RS-232 outputs and five monitoring inputs on a single low-voltage supply. Its three drivers can carry transmitted data and modem-control handshakes, while the five receivers can supervise request-to-send, data-ready, and other status signals. Operation from 3 V to 5.5 V simplifies interfacing with 3.3-V or 5-V embedded controllers, and the 250-kbps capability suits asynchronous console links. The connector-side ESD ratings of ±15 kV HBM and air-gap discharge and ±8 kV contact discharge add protection where service personnel connect cables.

📟

Data-Acquisition Equipment

The MAX3243ECDBR provides a compact RS-232 interface for laboratory and field data-acquisition equipment. Three driver channels support command transmission and flow-control outputs, while five receiver channels can read remote acknowledgements, triggers, and status flags. The 28-pin SSOP consolidates eight channels of RS-232 connectivity without requiring separate single-channel transceivers. A single 3-to-5.5-V rail supports both 3.3-V control electronics and 5-V legacy subsystems, and the specified 250-kbps rate is suitable for periodic measurement packets and configuration commands.

🔧

Embedded Controller Debug Port

The MAX3243ECDBR can implement a multi-signal RS-232 debug interface for an embedded control system. A controller at 3.3 V can use one driver for transmit data and additional drivers for handshake signals, while receivers monitor acknowledgement and module-status lines. The 250-kbps operating limit is appropriate for console traffic rather than high-rate file transfer. Its integrated dual charge pump eliminates a separate negative supply, and the 28-pin SSOP keeps the interface compact while providing five inputs for richer handshaking than a two-channel transceiver.

🛒

Point-of-Sale Terminal

The MAX3243ECDBR suits point-of-sale terminals that need both command output and multiple peripheral-status inputs. Three drivers can operate a transaction port and hardware handshakes, and five receivers can detect printer, scanner, drawer, and system-ready indications. The 3-to-5.5-V supply range allows use with either 3.3-V system logic or a 5-V interface controller. Because retail equipment frequently connects user-accessible RS-232 peripherals, the connector-side ESD ratings provide an important margin, while the 28-pin SSOP keeps routing manageable on a compact terminal board.

🧰

Instrumentation and Test Equipment

The MAX3243ECDBR is appropriate for programmable instrumentation that exchanges commands and status over RS-232. Three transmitted signals can carry serial data plus hardware flow control, and five received signals support remote triggers, interlock status, or acknowledgements from an external fixture. The 250-kbps rate matches typical instrument-control traffic, while the wide 3-to-5.5-V supply range accommodates mixed legacy and modern logic. The dual charge-pump architecture simplifies the power tree and reduces the number of external components compared with discrete driver-receiver implementations.

🌐

Network Management and Service Port

The MAX3243ECDBR supports a dedicated RS-232 service connection on routers, switches, and industrial controllers. The transmitter channels can drive console data and flow-control signals, while the receiver channels can monitor remote commands, reset requests, and power status. Its 250-kbps limit is well matched to human-driven terminal sessions and low-rate management commands. Because service ports are often exposed through physical connectors, the ±15-kV HBM and air-gap ESD ratings and ±8-kV contact rating are valuable system-level protections on the connector-side pins.

What is the MAX3243ECDBR used for?
The MAX3243ECDBR is a multichannel RS-232 interface IC for connecting a low-voltage controller to a cable-based serial port. It contains three line drivers, five line receivers, and a dual charge-pump circuit. According to the Texas Instruments MAX3243 datasheet, the device operates from 3 V to 5.5 V, supports rates up to 250 kbps, and meets TIA/EIA-232-F interface requirements.
How many RS-232 drivers and receivers does MAX3243ECDBR have?
The MAX3243ECDBR provides three RS-232 line drivers and five RS-232 line receivers. This 3/5 configuration allows one controller to transmit on three lines while monitoring five incoming signals, which is useful for modem-control handshakes, hardware flow control, and status inputs. The manufacturer datasheet identifies the device as a 3-to-5.5-V multichannel RS-232 line driver/receiver.
What is the maximum data rate of MAX3243ECDBR?
The MAX3243ECDBR supports serial data rates up to 250 kbps. Texas Instruments describes the MAX3243 as a 3-to-5.5-V multichannel RS-232 line driver/receiver with 250-kbps operation. The MAX3243ECDBR is supplied in a 28-pin SSOP package and includes ±15-kV HBM and IEC61000-4-2 air-gap ESD protection.
What is the MAX3243ECDBR supply voltage range?
The MAX3243ECDBR operates from 3 V to 5.5 V. This range allows the transceiver to connect directly to 3.3-V or 5-V controller logic while its integrated charge pumps produce the bipolar voltage levels required by RS-232 drivers. According to the Texas Instruments product page, the MAX3243 is a 3-to-5.5-V multichannel interface IC.
What ESD protection does MAX3243ECDBR provide?
The MAX3243ECDBR provides ±15 kV ESD protection under the HBM and IEC61000-4-2 air-gap discharge tests, and ±8 kV under the IEC61000-4-2 contact-discharge test on serial-port connection pins. These ratings are stated in the manufacturer datasheet and are particularly relevant when the RS-232 connector is exposed to user-accessible cables.
Where can I download the MAX3243ECDBR datasheet PDF?
The MAX3243ECDBR datasheet PDF is available through the Texas Instruments MAX3243 product page and the linked manufacturer PDF. The document describes the 28-pin SSOP device, electrical characteristics, pin descriptions, and the dual charge-pump implementation. Use the manufacturer datasheet when assigning pins, selecting bypass capacitors, and confirming RS-232 timing margins.
Where can I find the MAX3243ECDBR pinout?
The MAX3243ECDBR pinout appears in the pin-description section of the Texas Instruments MAX3243 datasheet. The device is a 28-pin SSOP with three driver channels, five receiver channels, supply and ground pins, and charge-pump connections. Use the datasheet pin table to map connector-side and logic-side functions before assigning PCB nets.
What is the best drop-in replacement for MAX3243ECDBR?
The closest verified drop-in replacement is the SP3243EBCA-L from SGS-Thomson, which offers the same 28-pin SSOP class of RS-232 interface and the same 3-driver/5-receiver channel count. The TRS3243EIDB from Texas Instruments is another 28-pin SSOP option with a closely matching function set. Confirm speed, ESD, supply, and pin-level details against the manufacturer datasheet before substitution.
Can TRS3243EIDB replace MAX3243ECDBR?
The TRS3243EIDB can be considered a drop-in alternative because both devices use a 28-pin SSOP and implement a 3/5 RS-232 transceiver with integrated charge pumps. Verify the exact pin mapping, operating-voltage range, maximum data rate, and ESD ratings before replacing the MAX3243ECDBR. Cross-reference documentation identifies it as a close functional match rather than an automatic interchange guarantee.
What is the best SGS-Thomson equivalent for MAX3243ECDBR?
The SP3243EBCA-L is the closest SGS-Thomson alternative identified for the MAX3243ECDBR because it provides a 3/5 RS-232 transceiver in a 28-pin SSOP package. It is a practical second-source choice for new designs and pin-compatible redesigns. Validate its data rate, supply limits, ESD ratings, and charge-pump capacitor requirements against the MAX3243 datasheet.
MAX3243ECDBR vs SP3243EBCA-L: which is better for an industrial console?
The MAX3243ECDBR is preferable when its 250-kbps rating, ±15-kV HBM protection, and ±8-kV contact-discharge rating are required by the interface specification. The SP3243EBCA-L is an effective second source with the same 3/5 channel arrangement and 28-pin SSOP format. For an industrial console, choose whichever part has the required speed, temperature range, and connector-side ESD rating.
Is the MAX3243ECDBR suitable for a 3.3-V embedded controller?
Yes, the MAX3243ECDBR is suitable for a 3.3-V embedded controller because its specified operating supply range is 3 V to 5.5 V. The charge-pump circuitry generates the bipolar RS-232 levels needed by the drivers, so the controller and transceiver can operate from a 3.3-V rail. Verify logic thresholds and timing in the manufacturer datasheet for the selected host device.
Does MAX3243ECDBR need an external negative supply voltage?
No, the MAX3243ECDBR does not require an external negative supply for normal operation. Its dual on-chip charge-pump circuit develops the bipolar voltage levels required by the RS-232 drivers from the 3-to-5.5-V system supply. The manufacturer datasheet specifies the required external charge-pump capacitor connections, which must be placed according to the recommended layout.
When should I choose MAX3243ECDBR over another RS-232 transceiver?
Choose the MAX3243ECDBR when the design needs three drivers, five receivers, a 3-to-5.5-V supply, and up to 250-kbps operation in a 28-pin SSOP. It is especially appropriate for RS-232 ports that expose multiple control lines or status inputs and require substantial ESD protection on connector-side pins. Select a different family when fewer channels, higher data rates, or smaller packages are required.
What are the key specifications of MAX3243ECDBR that engineers should know?
The key MAX3243ECDBR specifications are a 3-to-5.5-V supply range, 250-kbps maximum data rate, three drivers, five receivers, and a 28-pin SSOP package. According to the Texas Instruments datasheet, connector-side pins also provide ±15-kV HBM and IEC61000-4-2 air-gap protection plus ±8-kV IEC61000-4-2 contact protection. These parameters determine channel count, bus speed, supply compatibility, and connector protection.

Engineering reference data for MAX3243ECDBR — comparison, design guidance, and compliance information.

Selection Guide

Choose the MAX3243ECDBR when the board needs three RS-232 driver channels, five receiver channels, a 3-to-5.5-V supply, and operation at up to 250 kbps in a 28-pin SSOP. It is a strong fit for console ports, industrial controllers, and instruments that need multiple handshaking or status signals on connector-side pins. The SP3243EBCA-L is a useful SGS-Thomson second source when its data rate, temperature range, and ESD ratings meet the system requirement. The TRS3243EIDB is another same-package option, but its pin mapping, speed, and protection ratings should be checked directly. Use a smaller single-channel transceiver such as the MAX3221IPWR when only one transmit and one receive path is required. Because MAX3243-class devices are generally specified for lower-speed RS-232 links, choose a faster or more specialized transceiver family if the design exceeds 250 kbps.

Comparison with Alternatives

Parameter This Product SP3243EBCA-L TRS3243EIDB
Brand Texas Instruments SGS-Thomson Texas Instruments
Package 28-pin SSOP 28-pin SSOP - same 28-pin SSOP - same
Number of Drivers 3 3 3
Number of Receivers 5 5 5

Key Differentiators

  • Five receivers provide more monitoring channels than a standard two-channel RS-232 transceiver (vs MAX3221IPWR)
  • Three-driver channel count supports a full multi-signal RS-232 port (vs MAX3221IPWR)
  • Higher documented connector-side ESD ratings for exposed serial ports (vs TRS3243EIDB)
  • Wide low-voltage supply range supports mixed 3.3-V and 5-V controller systems (vs SP3243EBCA-L)

Design Notes

Place the charge-pump flyback capacitors and the V+ and V- capacitors directly beside their associated IC pins, with short and symmetric connections to the device. Keep these components away from connector-side driver outputs because switching current in the charge-pump network can couple into adjacent high-impedance receiver traces. Follow the manufacturer datasheet capacitor values and recommended layout because incorrect placement can reduce ESD performance and increase emissions.

Do not treat the MAX3243ECDBR logic-side inputs as 5-V-tolerant unless the selected pin meets the datasheet limits. Verify the host controller voltage, receiver thresholds, and maximum input voltage before connecting directly to a 3.3-V or 5-V system. Also avoid driving the three receiver outputs simultaneously with another device, because their outputs are intended to connect to high-impedance controller inputs.

Route connector-side RS-232 nets away from clocks, switching-power nodes, and sensitive analog inputs. Keep the ground reference continuous beneath the device and return connector current through the board ground rather than a narrow signal-ground path. The MAX3243ECDBR provides substantial connector-pin ESD ratings, but those ratings do not replace good enclosure grounding, cable design, and external surge protection in severe industrial environments.

Place the supply bypass capacitor at the VCC pin and use a low-inductance connection to the ground plane. The MAX3243ECDBR operates from 3 V to 5.5 V, but the correct bypass value and charge-pump capacitor values must follow the manufacturer datasheet. Check that the host controller and transceiver share a compatible ground reference, and avoid long supply traces that allow cable-side transients to disturb the charge-pump supply node.

Compliance Information

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

RoHS compliance is indicated for the MAX3243ECDBR listing. The RS-232 interface is a commercial interface product, so AEC-Q100 automotive qualification is not applicable. Other environmental declarations require manufacturer confirmation.

Related Searches

MAX3243ECDBR datasheet MAX3243ECDBR pinout MAX3243ECDBR datasheet pdf MAX3243ECDBR equivalent MAX3243ECDBR replacement MAX3243ECDBR cross reference MAX3243ECDBR price MAX3243ECDBR stock Texas Instruments MAX3243ECDBR MAX3243 28-SSOP pinout MAX3243ECDBR vs SP3243EBCA-L MAX3243ECDBR vs TRS3243EIDB MAX3243ECDBR RS-232 application circuit MAX3243ECDBR ESD protection what is MAX3243ECDBR used for

Related Components & Terms

Texas Instruments MAX3243ECDBR MAX3243 SP3243EBCA-L TRS3243EIDB MAX3221IPWR RS-232 TIA/EIA-232-F line driver line receiver RS-232 transceiver interface IC serial transceiver charge-pump circuit dual charge pump SSOP-28 surface mount SMD package 250 kbps 3 V to 5.5 V ESD protection HBM IEC61000-4-2 RoHS industrial serial console
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details