MC33901WEF - 1Mbps High-Speed CAN Transceiver | NXP
MPN: MC33901WEF ✗ End of LifeMC33901WEF Overview
A CAN transceiver is an interface circuit within the Controller Area Network hardware hierarchy. It converts logic-level signals from a CAN protocol controller into the differential voltage levels carried by the CAN bus, and converts received bus signals back into logic levels for the controller. The MC33901WEF family is designed for high-speed CAN networks requiring compact implementation, reliable bus signaling and protection against electrical transients.
The MC33901WEF provides a maximum specified CAN data rate of 1.0 Mbit/s. Its 8-pin SOIC package supports compact PCB placement, while the market-standard pin arrangement helps simplify replacement and board-layout planning. The component is listed with 5 V operation, normal and standby operating modes, automotive temperature grading and AEC-Q100 qualification. Manufacturer information also describes excellent EMC and ESD performance without requiring external filter components.
The SMARTMOS implementation is intended to provide efficient CAN physical-layer operation in industrial, automotive and embedded networking systems. Because the transceiver is the interface between digital controller logic and the physical bus, correct supply decoupling, termination and signal-integrity layout are essential. The SOIC package should be placed close to the CAN connector and the bus differential pair, with protection components positioned where they can divert surge and ESD energy without disrupting the signal path.
Typical applications include automotive CAN networks, industrial automation equipment, robotics, building controls, embedded motor-control systems and other distributed electronic systems that require a physical CAN interface. In these systems, the MC33901WEF allows the host MCU or dedicated CAN controller to communicate over the two-wire differential bus while keeping the physical-layer implementation compact.
Designers should verify the complete transceiver operating temperature range, supply tolerances, loop-delay limits, bus fault handling and pin-level behavior against the current manufacturer datasheet before release. The CAN bus must also use the correct 120-ohm termination arrangement, and unused or unused-mode pins should follow the datasheet requirements rather than being left open by assumption. The package and exposed electrical requirements should be checked against the PCB footprint and assembly process.
This page combines the manufacturer’s MC33901 family information, exact MPN listings, package details, replacement discussion and practical integration guidance. It is intended to help engineers identify the correct CAN transceiver, understand its physical-layer role and plan a compatible replacement before committing the 8-pin SOIC footprint to a PCB.
Drop-in alternatives for MC33901WEF — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MC33901WEF (same form factor and footprint) — differing in Package, Product Type, Maximum Data Rate, RoHS Status, Mounting Type.
MC34901WEF
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
TJA1042T/3/1J
✅ Drop-InContact for price
View Datasheet →TJA1040T/CM
✅ Drop-InContact for price
View Datasheet →TLE6250PG
✅ Drop-InContact for price
View Datasheet →SN65HVD230DR
✅ Drop-InContact for price
View Datasheet →MC33901WEF Specifications
| Product Type | High-speed CAN transceiver |
| Maximum CAN Data Rate | 1.0 Mbit/s |
| Supply Voltage | 5 V |
| Operating Mode | Normal and standby modes |
| Package | 8-pin SOIC |
| Pin Count | 8 pins |
| Mounting Type | Gull-wing surface mount |
| Package Code | SOP |
| Package Shape | Rectangular |
| Temperature Grade | Automotive |
| Automotive Qualification | AEC-Q100 |
| Bus Type | Controller Area Network, dual-wire differential bus |
| Bus Structure | Two-wire CAN bus |
| Technology | SMARTMOS |
| EMC Performance | Excellent EMC performance; external filter components not required |
| ESD Performance | Excellent ESD performance; external filter components not required |
| Host Interface | CAN protocol controller interface |
| Transceiver Configuration | 1/1 transceiver |
MC33901WEF Pin Configuration
| Pin 1 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 2 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 3 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 4 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 5 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 6 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 7 | NC — Not connected; use the manufacturer pin-description table for final assignment |
| Pin 8 | NC — Not connected; use the manufacturer pin-description table for final assignment |
Typical Applications
MC33901WEF is suitable for 6 applications: Automotive CAN Networks, Industrial Automation Equipment, Robotics and Motion Control, Building Control Networks, Embedded CAN Communication Modules, Power and Motor Management Systems.
Automotive CAN Networks
The MC33901WEF fits automotive CAN nodes because it is listed with an automotive temperature grade, AEC-Q100 qualification and operation up to 1.0 Mbit/s. It sits between a CAN protocol controller and the vehicle’s two-wire differential bus, translating controller logic into bus signaling and returning received bus states to the controller. The 8-pin SOIC footprint supports compact controller-area PCB placement. For an automotive program, engineers should still verify the exact temperature range, transient immunity and traceability requirements, especially because the device lifecycle status is obsolete.
Recommended
Industrial Automation Equipment
MC33901WEF is suitable for industrial controllers, remote I/O modules and factory automation equipment that use a high-speed CAN backbone. Its 1.0 Mbit/s capability provides sufficient bandwidth for distributed commands, diagnostics and sensor data, while the 8-pin SOIC package limits board area. Place the transceiver near the bus connector, maintain a continuous differential pair and install the bus termination according to the network topology. Industrial replacement designs should compare standby and fault-mode behavior with an approved equivalent before updating the PCB.
Recommended
Robotics and Motion Control
The MC33901WEF can connect a robot controller to motor drives, sensors and remote actuators over a deterministic CAN network. At rates up to 1.0 Mbit/s, the physical-layer device supports communication-heavy embedded systems without requiring a larger transceiver package. The two-wire CAN topology reduces signal count, and the SOIC package simplifies assembly beside the controller. Keep the CANH and CANL route geometry symmetrical, avoid ground-plane discontinuities beneath the pair and confirm that each branch uses the correct termination arrangement.
Recommended
Building Control Networks
MC33901WEF can serve as the physical-layer interface in HVAC controllers, lighting controllers, access-control nodes and other building automation equipment using CAN. The device provides a compact 8-pin SOIC solution with operation up to 1.0 Mbit/s for command and diagnostic traffic. Its physical-layer role keeps CAN controller logic isolated from the external differential bus. For low-cost maintenance replacements, engineers should qualify the exact alternative for pin behavior, supply tolerance, bus-fault recovery and environmental requirements rather than relying only on the shared CAN transceiver function.
Recommended
Embedded CAN Communication Modules
MC33901WEF is appropriate for compact embedded modules that expose a CAN bus to a host MCU or communication processor. Its 1.0 Mbit/s rate supports real-time command exchange, status reporting and diagnostic functions, while the market-standard 8-pin SOIC arrangement simplifies board integration. Place input and ground connections directly beside the transceiver, keep the differential bus pair away from switching nodes and provide local supply bypassing. An equivalent may simplify obsolescence management, but its standby, loop-delay and protection characteristics must match the module’s communication timing and fault-recovery requirements.
Recommended
Power and Motor Management Systems
MC33901WEF can provide the CAN physical interface in inverter controllers, power-conversion modules and compact motor-management units. The 1.0 Mbit/s transceiver enables status, command and protection information to travel over the two-wire bus between a controller and power electronics. Its small SOIC package helps preserve board area, while normal and standby modes support system power management. Use the transceiver data sheet to confirm mode-control polarity and fault behavior; MC33901WEF is obsolete, so a managed redesign should evaluate a supported equivalent and revalidate protection performance.
Recommended
Recommended Products Summary
Engineering reference data for MC33901WEF — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MC34901WEF | TJA1042T/3 | TJA1040 | TLE6250 | SN65HVD230 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | Infineon Technologies | Texas Instruments |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver |
| Bus Structure | Two-wire differential CAN bus | Two-wire differential CAN bus | Two-wire differential CAN bus | Two-wire differential CAN bus | Two-wire differential CAN bus | Two-wire differential CAN bus |
Key Differentiators
- Automotive-grade qualification (vs SN65HVD230)
- Documented EMC and ESD positioning (vs TLE6250)
- Obsolescence-management replacement support (vs MC34901WEF)
Design Notes
Route CANH and CANL as a closely coupled differential pair with continuous reference to a solid ground plane. Keep the pair short from the transceiver to the connector or protection component, minimize stubs and avoid crossing switching-node copper. The NXP family documentation states that external filter components are unnecessary, but the pair still requires controlled geometry to preserve differential signal integrity.
Do not assume that every high-speed CAN transceiver is a drop-in replacement merely because it uses an 8-pin SOIC. Compare pin assignments, standby-control polarity, TXD and RXD logic levels, bus-fault behavior, loop delay and ESD capability against the MC33901WEF data sheet. TJA1042T/3 is explicitly supported in NXP community replacement discussion; other candidates require project-specific validation.
Place the transceiver supply bypass capacitor close to the device supply and ground pins, and keep the return path short to the surrounding ground plane. Separate the CAN routing from noisy power-converter paths where practical. The MC33901WEF is a 5 V device, so validate supply tolerance and sequencing against the host controller to prevent unintended TXD or standby states during power transitions.
MC33901WEF is identified as obsolete. For maintenance production, request exact-MPN availability and traceability through the Request a Quote form. For new designs, qualify a current alternative and rerun bus timing, EMC, ESD, fault-recovery and system-level power-cycle tests. Do not mix an obsolete device into a new PCB without confirming whether its original qualification records remain usable for the end application.
Compliance Information
AEC-Q100 qualification and automotive temperature grading are identified in distributor product information. Other compliance fields are unknown because explicit declarations were not included in the available manufacturer page snippets.