NXP Semiconductors

TJA1042T/3 - 5Mbit/s CAN Transceiver, SOIC-8 | NXP

MPN: TJA1042T/3 ✗ End of Life
4.5V to 5.5V Vdss SAE J2284-1 through SAE J2284-5 Rds(on) 8-pin SOIC, 3.0 mm x 3.0 mm body Package
MOQ: 1 |

TJA1042T/3 Overview

The NXP Semiconductors TJA1042T/3 is a high-speed CAN transceiver with Standby mode, providing a physical-layer interface between a CAN protocol controller and a two-wire CAN bus. It supports CAN FD fast-phase communication at data rates up to 5 Mbit/s, operates from a 4.5V to 5.5V supply, and supports 3V to 5V microcontroller interfacing through its VIO interface. The device is packaged in an 8-pin SOIC.

A CAN transceiver is an interface IC that converts logic-level signals from a CAN controller into the dominant and recessive voltage states used on a differential CAN bus. It also converts bus levels into receive data for the controller. The TJA1042 belongs to the high-speed CAN transceiver category within the broader network-interface IC and automotive communication hierarchy.

The TJA1042T/3 provides differential transmit and receive capability, a low-power Standby mode, and bus wake-up capability. It can remain passive when unpowered, helping the connected CAN network enter a low-current state. The VIO interface allows direct connection to microcontrollers operating from 3V to 5V, while the main transceiver supply operates from 4.5V to 5.5V.

The TJA1042 implements the CAN physical layer defined by ISO 11898-2:2016 and the SAE J2284-1 through J2284-5 specifications identified in the NXP documentation. These standards establish the electrical behavior expected of high-speed CAN nodes, including bus signaling, termination, timing, and fault behavior.

Typical uses include automotive body and comfort modules, industrial CAN gateways, engine controllers, battery-management systems, and embedded control units that communicate over a two-wire CAN network. Its 5Mbit/s capability makes it appropriate for systems that combine conventional CAN traffic with the faster data phase of CAN FD.

Designers should connect the CANH and CANL pins to the protected bus network, provide the bus-side termination specified by the system architecture, and use a suitable common-mode choke or ESD protection where required. VIO should be connected to the microcontroller interface supply, while VCC must satisfy the 4.5V to 5.5V operating range.

This page combines the manufacturer specifications, package information, interface standards, drop-in candidates, and application guidance needed to evaluate the TJA1042T/3 as a high-speed CAN physical-layer interface for automotive and industrial control systems.

Drop-in alternatives for TJA1042T/3 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

Variants in this series

Same-series models that are drop-in compatible with TJA1042T/3 (same form factor and footprint) — differing in Package, Product Type, Bus Interface, Operating Temperature, CAN Protocol Support.

Texas Instruments
Package: 8-SOIC
Product Type: Fault-protected CAN transceiver
Bus Interface: Differential CANH and CANL
Texas Instruments
Package: SOIC (D), 8 pins
Operating Temperature: -55C to +125C
NXP Semiconductors
Package: 8-pin SOIC
Product Type: High-speed CAN bus transceiver
Bus Interface: CANH and CANL differential outputs
NXP Semiconductors
Product Type: High-speed CAN / CAN FD transceiver family
Operating Temperature: -40 °C to +150 °C (AEC-Q100 Grade 0)
Infineon
Package: PG-DSO-8
Product Type: CAN FD Transceiver
Operating Temperature: -40 C to +150 C

TJA1051T/3/1J

✅ Drop-In
NXP Semiconductors
📦 SOIC-8
High-speed CAN bus transceiver · Controller Area Network · 5 Mbit/s · 5.5 V maximum · 3 V to 5 V · Two-wire differential CAN bus · 1/1 half transceiver · 3 V to 5 V compatible

Contact for price

View Datasheet →

TCAN1042HD

✅ Drop-In
Texas Instruments
📦 SOIC-8
Fault-protected CAN transceiver · Classic CAN and CAN FD · 2 Mbps · 1 · 1 · 4.5 V to 5.5 V · -55°C to +125°C · 8-SOIC

Contact for price

View Datasheet →

TCAN1042VDRQ1

✅ Drop-In
Texas Instruments
📦 SOIC-8
CAN FD Transceiver · CAN, CAN FD (flexible data-rate) · 5 Mbps · 4.5 V to 5.5 V · Yes, VIO pin for 3.3V/5V logic · 1/1 · Half · CANH/CANL short to battery and ground

✗ Out of Stock

$0.33923 / Unit

View Datasheet →

TJA1042T/3 Specifications

Product Type High-speed CAN transceiver with Standby mode
Supported Protocol CAN and CAN FD fast phase
Maximum CAN Data Rate 5 Mbit/s
Main Supply Voltage Range 4.5V to 5.5V
VIO Supply Voltage Range 3V to 5V
Bus Interface Differential two-wire CAN bus
Transmit and Receive Capability Differential
Low-Power Mode Standby mode with CAN bus wake-up
Unpowered Behavior Passive behavior
CAN Physical-Layer Standard ISO 11898-2:2016
Automotive Interface Standards SAE J2284-1 through SAE J2284-5
Microcontroller Interface VIO interface for 3V to 5V microcontrollers
Package 8-pin SOIC, 3.0 mm x 3.0 mm body
Mounting Type Surface mount

TJA1042T/3 8-pin soic, 3.0 mm x 3.0 mm body Pin Configuration Guide

Pin configuration for TJA1042T/3 (8-pin soic, 3.0 mm x 3.0 mm body package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.

8-pin soic, 3.0 mm x 3.0 mm body package pinout diagram for TJA1042T/3

No detailed pinout data available for TJA1042T/3.

Refer to the datasheet for full pin configuration.

Typical Applications

TJA1042T/3 is suitable for 6 applications: Automotive Body Control Modules, Industrial CAN Gateways, Battery Management Systems, Engine and Powertrain Controllers, Embedded CAN Sensor Nodes, Test and Measurement Equipment.

🚗

Automotive Body Control Modules

The TJA1042T/3 fits body-control and comfort modules that exchange commands and sensor status over a two-wire CAN network. Its differential CAN interface supports CAN FD fast-phase rates up to 5Mbit/s, while the 4.5V-to-5.5V VCC range and separate 3V-to-5V VIO interface allow connection to controllers operating at different logic levels. The 8-pin SOIC package simplifies placement in compact automotive controller boards. Standby mode and CAN-bus wake-up are useful when the module must reduce current consumption without becoming isolated from the vehicle network. The /3 variant should be selected specifically when the controller interface uses VIO, because related TJA1042 variants may provide SPLIT on pin 5 instead.

🏭

Industrial CAN Gateways

The TJA1042T/3 is appropriate for industrial gateways that connect embedded controllers to two-wire CAN equipment. Its documented capability of 5Mbit/s in the CAN FD fast phase supports gateways handling high-volume status and control traffic while remaining compatible with conventional CAN nodes. The separate VIO supply permits direct interfacing with 3V or 5V microcontrollers, reducing level-shifting circuitry when the logic supply already matches. Low-power Standby operation and wake-up through the CAN bus support equipment that normally sleeps but must respond when another node initiates communication. PCB implementation still requires controlled bus routing, appropriate termination, protection appropriate to the installation environment, and validation of common-mode levels.

⚡

Battery Management Systems

The TJA1042T/3 can serve as the physical-layer interface between a battery-management controller and a vehicle or industrial CAN network. Differential transmit and receive operation provides noise-resistant communication for pack state, balancing commands, fault information, and system diagnostics. The device supports data rates up to 5Mbit/s in the CAN FD fast phase, which is useful when the controller uses segmented CAN FD frames. Its 3V-to-5V VIO interface can connect to suitable low-voltage controllers while the transceiver's main supply remains within 4.5V to 5.5V. Standby mode and CAN-bus wake-up help a management unit remain responsive while controlling quiescent consumption during inactive periods. The exact electrical and qualification requirements of the battery platform must be verified before production use.

🚗

Engine and Powertrain Controllers

The TJA1042T/3 is suitable for CAN-connected engine and powertrain control units requiring a robust physical-layer interface. Differential signaling supports communication over the two-wire CAN network, and operation up to 5Mbit/s accommodates CAN FD fast-phase traffic used for control data. The VIO interface lets the transceiver connect with a 3V-to-5V controller without imposing the controller's lower supply voltage on the main transceiver rail. Low-power Standby mode can reduce activity in appropriate operating states, while bus wake-up helps the controller recognize an addressed network request. Because these systems impose strict EMC, transient, fault-containment, and qualification requirements, engineers should validate the complete module against its automotive specification rather than relying on generic transceiver functionality.

🧩

Embedded CAN Sensor Nodes

The TJA1042T/3 can connect a compact sensor or actuator node to a CAN-based monitoring network. The 3V-to-5V VIO interface is useful for low-power microcontrollers, while the main transceiver supply remains independently constrained to 4.5V to 5.5V. At data rates up to 5Mbit/s, the interface can support CAN FD fast-phase messages carrying richer sensor payloads or diagnostic data. Standby mode and CAN-bus wake-up allow remote nodes to reduce consumption and still become active when bus activity occurs. Designers should minimize CANH and CANL trace separation changes, preserve the intended termination topology, and place protection close to the external connector so transient energy does not propagate into the controller.

🖥️

Test and Measurement Equipment

The TJA1042T/3 can provide a CAN interface for test equipment, diagnostic programmers, and communication analyzers that need to participate in an operating vehicle or industrial CAN network. Differential receive and transmit functions allow the instrument to exchange command, diagnostic, and logging traffic, while operation up to 5Mbit/s supports CAN FD fast-phase analysis. The VIO interface accommodates compatible controller logic levels and the separate main supply helps organize analog and digital power domains. Standby mode is useful in portable instruments that should reduce consumption between test sequences, and CAN-bus wake-up can provide network-directed activation. External protection and isolation requirements depend on the distance, environment, and ground-potential difference of the equipment under test.

What is the operating voltage of TJA1042T/3?
The TJA1042T/3 operates from 4.5V to 5.5V on its main VCC supply and supports a separate 3V to 5V VIO supply for direct connection to compatible microcontrollers. According to the NXP TJA1042 product data sheet, the VIO arrangement allows the transceiver to interface with 3V and 5V controller families while maintaining the required CAN-side supply range. Confirm both rails remain within their specified limits across temperature, transients, and power-sequencing conditions.
What data rate does TJA1042T/3 support?
The TJA1042T/3 supports CAN FD fast-phase communication at data rates up to 5 Mbit/s. The NXP TJA1042 product data sheet states that its ISO 11898-2:2016 and SAE J2284-1 through J2284-5 implementation enables reliable CAN FD fast-phase operation. This rate should be treated as a node-level capability and verified against the controller, clocking, wiring, termination, and electromagnetic-compatibility requirements of the complete network.
Where can I download the TJA1042T/3 datasheet PDF?
The official TJA1042T/3 datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1042.pdf. This manufacturer document describes the CAN physical-layer implementation, electrical characteristics, pin functions, operating modes, application information, and the differences among TJA1042 package and interface variants. Use the manufacturer's revision when making compliance, EMC, or PCB design decisions because index pages and third-party copies may represent different revisions.
Where can I find the TJA1042T/3 pinout?
The TJA1042T/3 pinout is documented in the NXP TJA1042 product data sheet at https://www.nxp.com/docs/en/data-sheet/TJA1042.pdf. The 8-pin SOIC variant uses the VIO-compatible /3 interface arrangement. Assign PCB nets directly from the manufacturer's pin-description table and package drawing, especially for VCC, VIO, CANH, CANL, RXD, TXD, STB, and ground. Verify the suffix-specific ordering code because related TJA1042 variants can place a different function on pin 5.
What is the difference between TJA1042T/3 and TJA1042T?
The principal functional difference is the interface supply arrangement on pin 5: TJA1042T/3 provides VIO for direct interfacing with 3V to 5V microcontrollers, while TJA1042T provides SPLIT for stabilizing the recessive bus level. NXP also identifies the standard TJA1042T as NRND. These are not automatically interchangeable on an existing PCB, so engineers should compare the exact pin functions, package drawing, supply requirements, and bus behavior before considering a substitution.
TJA1042T/3 vs TJA1051T/3 - which CAN transceiver should I choose?
Choose the TJA1042T/3 when the design specifically requires its documented Standby mode, CAN-bus wake-up capability, passive unpowered behavior, and 5Mbit/s CAN FD fast-phase operation. The TJA1051T/3 is also identified as a 5Mbit/s 8-pin SOIC high-speed CAN transceiver with a 3V interface option, so it is a close functional candidate. Final selection should verify standby or sleep behavior, wake-up requirements, pin-level compatibility, EMC performance, and lifecycle status against the target system.
Is TJA1042T/3 suitable for automotive CAN FD networks?
The TJA1042T/3 is suitable for high-speed CAN networks that use the CAN FD fast phase at rates up to 5Mbit/s, and its documentation identifies automotive applications and SAE J2284-1 through J2284-5 interface behavior. The component also supports low-power Standby operation and CAN-bus wake-up. Automotive qualification requirements, including AEC-Q100 status, should be confirmed with NXP for the exact ordering code and customer program before production release.
What can replace TJA1042T/3?
The closest documented alternatives are TJA1051T/3/1J, TCAN1042H, and TCAN1042, each of which must be checked for SOIC-8 footprint and pin-level compatibility before substitution. The TJA1051T/3/1J is a 5Mbit/s 8-pin SOIC CAN transceiver with a 3V interface option. TCAN1042 devices differ in undervoltage thresholds and VIO limits, while target TJA1042T/3 versions use VIO rather than the SPLIT function found on some related TJA1042 variants.
Is TJA1042T/3 the same as TJA1042T/3/1J?
TJA1042T/3/1J is the orderable form associated with the TJA1042T/3 device family, while TJA1042T/3 is the base designation used for technical comparison. The /1J identifier identifies the specific ordering and delivery format rather than creating a different transceiver function. Engineers should use the full manufacturer ordering code when placing a procurement request and verify the package, temperature range, tape-and-reel configuration, and lifecycle status in the NXP product information.
When should I choose TJA1042T/3 over TCAN1042H?
Choose the TJA1042T/3 when a design specifically depends on the documented NXP standby and bus-wake-up behavior, passive operation while unpowered, or its 3V-to-5V VIO interface. Choose TCAN1042H after validating its undervoltage thresholds and interface voltages against the existing design; published comparisons report a lower VCC undervoltage threshold for the TJA1042 family than for TCAN1042H, plus different minimum VIO levels. These differences can affect marginal power states and should not be ignored.
Where can I buy TJA1042T/3 online?
Use the Request a Quote form on this page to request TJA1042T/3 availability, current lead time, and the exact ordering suffix required for your production process. The form allows buyers to specify the SOIC-8 package, tape-and-reel format, quantity, and delivery destination without relying on a static price. Before releasing an order, confirm the current lifecycle status because the related TJA1042T family listing is marked NRND by NXP.
What is the price of TJA1042T/3?
The current commercial terms for TJA1042T/3 are available through the Request a Quote form on this page. The form captures quantity, package, and delivery requirements so the current offer can reflect the exact order configuration and market conditions. For production planning, request the full suffix and quantity break, then confirm lead time and any lifecycle constraints for the NXP TJA1042 family in the same communication.
What is the lead time for TJA1042T/3?
The current lead time for TJA1042T/3 should be requested through the Request a Quote form on this page, including the required quantity and package delivery format. Lead time can vary with order quantity, allocation status, and the lifecycle position of the exact NXP ordering code. Because the related TJA1042T product listing is marked NRND, obtain written supply confirmation before committing a new production design or approving a long-term purchasing plan.
Is TJA1042T/3 in stock?
Current TJA1042T/3 stock and delivery availability can be requested through the Request a Quote form on this page. Include the quantity, tape-and-reel or other delivery format, and target date so the supply response reflects the actual order requirement. NXP lists the related TJA1042T family as NRND, making lot availability and lifecycle confirmation especially important for scheduled automotive, industrial, or aftermarket production.
What are the key specifications of TJA1042T/3 that engineers should know?
The TJA1042T/3 is an 8-pin SOIC high-speed CAN transceiver with a 4.5V-to-5.5V main supply, a 3V-to-5V VIO interface, and CAN FD fast-phase operation up to 5Mbit/s. The NXP TJA1042 product data sheet also identifies ISO 11898-2:2016 behavior, SAE J2284-1 through J2284-5 compatibility, Standby mode, CAN-bus wake-up, and passive unpowered behavior. These parameters define its electrical, protocol, and low-power capabilities.
What is the best NXP equivalent for TJA1042T/3?
The TJA1051T/3/1J is the closest identified NXP-family candidate because it is an 8-pin SOIC high-speed CAN transceiver supporting 5Mbit/s operation and a 3V interface arrangement. However, it is not automatically a drop-in replacement: standby or sleep behavior, wake-up logic, supply thresholds, EMC qualifications, and exact pin functions must be compared. For an unmodified PCB, confirm pin compatibility and the complete electrical requirements rather than relying only on the shared package and speed.

Engineering reference data for TJA1042T/3 — comparison, design guidance, and compliance information.

Selection Guide

Choose the TJA1042T/3 when the design requires an 8-pin SOIC high-speed CAN transceiver with operation up to 5Mbit/s, a 3V-to-5V VIO interface, Standby mode, CAN-bus wake-up, and passive unpowered behavior. It is particularly appropriate for low-voltage microcontrollers that cannot use the SPLIT arrangement found on the standard TJA1042T. Consider TJA1051T/3/1J when its low-power behavior and lifecycle position better match the project, but validate every pin and operating state before substitution. TCAN1042H and TCAN1042 are close candidates for an SOIC-8 CAN design, although their reported VCC undervoltage and VIO thresholds differ from those of the TJA1042 family. For an existing PCB, package size alone is not sufficient: confirm pin 5, STB polarity, RXD and TXD behavior, supply sequencing, wake-up logic, and qualification requirements before approving any replacement.

Comparison with Alternatives

Parameter This Product TJA1051T/3/1J TCAN1042H TCAN1042
Manufacturer NXP Semiconductors NXP Semiconductors Texas Instruments Texas Instruments
Package SOIC-8 SOIC-8 SOIC-8 SOIC-8

Key Differentiators

  • Supports 3V-to-5V microcontroller interfacing through VIO (vs TJA1042T)
  • Documented low-power network behavior (vs TCAN1042H)
  • Lower reported undervoltage threshold (vs TCAN1042H)
  • 5Mbit/s CAN FD fast-phase operation with NXP low-power features (vs TJA1051T/3/1J)

Design Notes

Route CANH and CANL as a tightly coupled differential pair with continuous reference to a common ground plane, avoiding plane splits, test pads, and unnecessary stubs. Keep the transceiver close to the protection components and external connector to minimize trace area exposed to radiated and conducted disturbances. Follow the NXP package drawing and pin-description table when assigning the 8-pin SOIC nets, and do not substitute the SPLIT function of a non-/3 TJA1042 variant for the VIO function required by the /3 device.

Provide separate, stable VCC and VIO rails according to the device requirements: VCC must remain within 4.5V to 5.5V, while VIO supports 3V to 5V microcontroller interfacing. Place the VCC and VIO decoupling capacitors close to their corresponding pins and keep return-current paths short. Account for rail sequencing, startup transients, and the possibility that VIO or VCC may be removed before the CAN bus. The passive unpowered behavior helps bus integrity, but external protection and supply design still determine fault tolerance.

Do not treat a shared SOIC-8 footprint as proof that every related transceiver is interchangeable. The TJA1042T/3 uses the VIO interface arrangement, whereas the TJA1042T uses SPLIT on pin 5; related pin-function changes can make an apparently identical package electrically incompatible. Before substituting TCAN1042, TCAN1042H, or TJA1051T/3, compare TXD polarity, RXD behavior, STB polarity, supply thresholds, wake-up logic, and transceiver sleep states. Also verify the exact NXP ordering suffix and lifecycle position before committing the PCB to production.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

The NXP documentation identifies ISO 11898-2:2016 and SAE J2284-1 through SAE J2284-5 interface behavior, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not identified for the exact ordering code.

Data verified on: 2026-11-09 — data verified and curated by XAIPART's component engineering team

Related Searches

tja1042t 3 datasheet tja1042t 3 1j datasheet tja1042t datasheet tja1042t 1j nxp TJA1042T/3 datasheet pdf TJA1042T/3 pinout TJA1042T/3 equivalent TJA1042T/3 replacement TJA1042T/3 vs TJA1051T/3 TJA1042T/3 5Mbit CAN FD TJA1042T/3 SOIC-8 TJA1042T/3 automotive CAN TJA1042T/3 price TJA1042T/3 stock NXP TJA1042T/3

Related Components & Terms

NXP Semiconductors TJA1042T/3 TJA1042T/3/1J TJA1051T/3/1J TCAN1042H TCAN1042 CAN transceiver high-speed CAN CAN FD Controller Area Network physical-layer interface differential transceiver VIO interface SPLIT function Standby mode CAN bus wake-up passive unpowered behavior ISO 11898-2:2016 SAE J2284-1 SAE J2284-5 4.5V to 5.5V supply 3V to 5V microcontroller interface 5Mbit/s data rate SOIC-8 surface-mount package
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details